Peerless 3P605NT - Manual
Peerless 3P605NT – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Seed Box Agitator Option; See; Figure 2
- Page 3 – Installation Instructions; Drive Assembly; Figure 3
- Page 4 – Figure 4; Install 16 tooth splined; Figure 5; Route chains as follows:
- Page 5 – Figure 6; P600 Drive w/Small Seeds Option; • Place 17 tooth sprocket (5) near left drill
- Page 6 – Figure 7; Figure 8
- Page 7 – Agitator Paddle Installation
© Copyright 2000 Printed
Great Plains Mfg., Inc.
Used with:
Installation Instructions
151-071M
6 Foot Drill
Seed Box Agitator Option
• 605NT
• 3P605NT
• 3P600
General Information
Assembly Instructions
When you see this symbol, the subsequent instructions and
warnings are serious - follow without exception. Your life and
the lives of others depend on it!
!!
Agitator Shaft
See
Figure 1
Seed Box Cover Removal
18726
1.
Remove covers (1) from inside both ends of
seed box by removing bolt (2), lock washer (3)
and hex nut (4).
4/26/2000
Before You Start
Beginning on page 8 are detailed listings of parts
included in the agitator option packages. Use the
proper list to inventory parts received.
Definitions
Right-hand and left-hand as used in this manual
are determined by facing the direction the ma-
chine will travel while in use unless otherwise
stated.
These instructions explain how to install the agita-
tor option. The agitator stirs the seed directly
above the metering cups. It is intended to cut
down on the "bridging" of light fluffy seeds.
These instructions apply to:
118-748A
3P600 Agitator w/Drive - 7-1/2"
118-749A
3P600 Agitator w/o Drive - 7-1/2"
118-750A
3P605NT & 605NT Agitator
w/Drive
118-751A
3P605NT & 605NT Agitator w/o
Drive
118-788A
3P600 Agitator w/Drive - 6"
118-789A
3P600 Agitator w/o Drive - 6"
Manual Update
Refer to the 6 foot drill operator’s manual for de-
tailed information on safely operating, adjusting,
troubleshooting and maintaining the agitator op-
tion. Refer to the parts manual for part
identification.
Drill Manual Part Numbers
151-061M
605NT & 3P605NT Operator’s
Manual
151-061P
605NT & 3P605NT Parts Manual
118-794M
3P600 Operator’s Manual
118-794P
3P600 Parts Manual
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
151-071M 3/31/2004 Great Plains Mfg., Inc. Seed Box Agitator Option 2 5. Slide lock collars (8 and 10) against bearing and flanges (7 and 11) and tighten set screws. See Figure 2 Agitator shaft Installation 18727 Figure 2: 2. Slide agitator shaft (5) into seed box from left side of drill. 3. As shaf...
3/31/2004 151-071M Great Plains Mfg., Inc. 3 Installation Instructions Drive Assembly 605NT and 3P605NT DriveNOTE: If your drill is equipped with a native grass option, a majority of the agitator drive is already installed. Go to page 4 for chain routing. See Figure 3 605NT & 3P605NT Drive Assem...
151-071M 3/31/2004 Great Plains Mfg., Inc. Seed Box Agitator Option 4 5. Refer to Figure 4. Figure 4 Gearbox Sprocket 18728 Install 16 tooth splined sprocket (11) to gearbox as shown, and fas-ten with snap ring (12). See Figure 5 18730 Agitator Chain Routing with Native Grass Agitator Chain Routing ...
