Peerless 151-071M - Manual

Peerless 151-071M – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – Seed Box Agitator Option; See; Figure 2
Page 3 – Installation Instructions; Drive Assembly; Figure 3
Page 4 – Figure 4; Install 16 tooth splined; Figure 5; Route chains as follows:
Page 5 – Figure 6; P600 Drive w/Small Seeds Option; • Place 17 tooth sprocket (5) near left drill
Page 6 – Figure 7; Figure 8
Page 7 – Agitator Paddle Installation

Loading the manual

Great Plains Mfg., Inc.

Used with:

Installation Instructions

151-071M

6 Foot Drill

Seed Box Agitator Option

• 605NT

• 3P605NT

• 3P600

General Information

Assembly Instructions

When you see this symbol, the subsequent instructions and
warnings are serious - follow without exception. Your life and
the lives of others depend on it!

Agitator Shaft
See

Figure 1

Seed Box Cover Removal

18726

Figure 1:

Remove covers (1) from inside both ends of
seed box by removing bolt (2), lock washer (3)
and hex nut (4).

4/26/2000

Before You Start

Beginning on page 8 are detailed listings of parts
included in the agitator option packages. Use the
proper list to inventory parts received.

Definitions
Right-hand and left-hand as used in this manual
are determined by facing the direction the ma-
chine will travel while in use unless otherwise
stated.

These instructions explain how to install the agita-
tor option. The agitator stirs the seed directly
above the metering cups. It is intended to cut
down on the "bridging" of light fluffy seeds.

These instructions apply to:

118-748A

3P600 Agitator w/Drive - 7-1/2"

118-749A

3P600 Agitator w/o Drive - 7-1/2"

118-750A

3P605NT & 605NT Agitator

w/Drive

118-751A

3P605NT & 605NT Agitator w/o
Drive

118-788A

3P600 Agitator w/Drive - 6"

118-789A

3P600 Agitator w/o Drive - 6"

Manual Update

Refer to the 6 foot drill operator’s manual for de-
tailed information on safely operating, adjusting,
troubleshooting and maintaining the agitator op-
tion. Refer to the parts manual for part
identification.

Drill Manual Part Numbers

151-061M

605NT & 3P605NT Operator’s

Manual

151-061P

605NT & 3P605NT Parts Manual

118-794M

3P600 Operator’s Manual

118-794P

3P600 Parts Manual

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Seed Box Agitator Option; See; Figure 2

151-071M 3/31/2004 Great Plains Mfg., Inc. Seed Box Agitator Option 2 5. Slide lock collars (8 and 10) against bearing and flanges (7 and 11) and tighten set screws. See Figure 2 Agitator shaft Installation 18727 Figure 2: 2. Slide agitator shaft (5) into seed box from left side of drill. 3. As shaf...

Page 3 - Installation Instructions; Drive Assembly; Figure 3

3/31/2004 151-071M Great Plains Mfg., Inc. 3 Installation Instructions Drive Assembly 605NT and 3P605NT DriveNOTE: If your drill is equipped with a native grass option, a majority of the agitator drive is already installed. Go to page 4 for chain routing. See Figure 3 605NT & 3P605NT Drive Assem...

Page 4 - Figure 4; Install 16 tooth splined; Figure 5; Route chains as follows:

151-071M 3/31/2004 Great Plains Mfg., Inc. Seed Box Agitator Option 4 5. Refer to Figure 4. Figure 4 Gearbox Sprocket 18728 Install 16 tooth splined sprocket (11) to gearbox as shown, and fas-ten with snap ring (12). See Figure 5 18730 Agitator Chain Routing with Native Grass Agitator Chain Routing ...