Paradyne EAM2000-12 - Manual
Paradyne EAM2000-12 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – E1 RJ21 Connector Port Pinout; OVERVIEW; Accessing EAM2000-12 data in a newly installed IP DSLAM; MUM installed in your IP DSLAM.; NOTE
- Page 3 – superuser / Password; Accessing EAM2000-12 data in a previously installed IP DSLAM; illuminated, indicating the connection has been established.; Default Settings; Management Password Administration Defaults*
- Page 4 – Management System Configuration Defaults; Data Storage
- Page 5 – Alternate Mark Inversion; Timing; Loop; The transmit clock source will originate from the remote E1 modem.
- Page 6 – ADDITIONAL INFORMATION; LED Indicators
- Page 7 – Regulatory Compliance; This Class A product complies with European Norm EN55022.
210-0000036 rev03
EAM2000-12
12-Port E1 Access Multiplexer
INSTALLATION
1. Unpack and inspect the EAM2000-12.
If there is visible damage, do not attempt to connect the device; contact Customer Support at 1-
877-638-2638 (001-603-427-0600 for international customers) or [email protected].
2. Install the EAM2000-12 in an IP DSLAM chassis.
All Access Multiplexer Modules for Net to Net Technologies' IP DSLAMs are hot swappable;
installing or removing an Access Module while the chassis is powered up does not affect the
operational status of other Access Modules within the chassis. The IPD12000 is a fourteen slot
chassis; slots 1-12 are reserved for Access Modules (such as the EAM2000-12) and slots 13-14
are reserved for Multiplexer Uplink Modules (such as the MUM200-2). Access Modules may be
placed in any order in slots 1-12. The IPD4000 is a five slot chassis; slots 1-4 are reserved for
Access Modules and slot 5 is reserved for a Multiplexer Uplink Module.
a. Align the EAM2000-12 with the slot module guides of the chosen slot for installation (slot
1-12 on the IPD12000 or slot 1-4 on the IPD4000).
b. Slide the EAM2000-12 firmly into the chassis. DO NOT USE EXCESS FORCE.
c. Secure the EAM2000-12 by tightening the fastening screws on the module faceplate.
d. Verify that the PWR (Power) LED on the EAM2000-12 faceplate is illuminated.
Interface
Module User Guide
CAUTION
Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions
when handling this equipment.
NOTE
There must be a Multiplexer Uplink Module installed in the IP DSLAM chassis in order for Access Modules to
operate.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
210-0000036 rev03 3. Connect the E1 Line(s). Plug the E1 cable into the RJ21 connector for the chosen slot on the back of the IP DSLAM. The EAM2000-12 will connect with remote E1 modems at distances up to 6,000 feet before requiring an E1 repeater. For each port being connected to a remote E1 modem,...
210-0000036 rev03 ! 192.168.254.252 if the MUM is in slot 13 (IPD12000) or slot 5 (IPD4000) ! 192.168.254.253 if the MUM is in slot 14 (IPD12000) e. Log in with a default username and password (both of which are case sensitive). Please note that General Users have "read only" access; for NMS...
210-0000036 rev03 Management System Configuration Defaults EAM2000-12 Circuit Defaults Data Storage Configuration backup is inherent in the EAM2000-12. Upon initial power up of the IP DSLAM, the default parameters of the EAM2000-12 will remain in place unless changed through NMS. Once changed, new c...
