Paradyne 5620 - Manual
Paradyne 5620 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Package Checklist; What Does the Hotwire 5620 RTU Do?
- Page 3 – DSL Access with a Hotwire 5038 Distributed POTS Splitter
- Page 4 – DSL Access without a POTS Splitter; Network
- Page 5 – Installing the DSL Access Wiring; Procedure; Important Safety; Bridge Clip; Punchdown Block; Demarcation Point
- Page 7 – RJ11 Wall Jack; or; Wiring can be run from the
- Page 8 – Installing the Hotwire 5620 RTU; Hotwire RTU; Customer
- Page 11 – Optional RTU Wall Placement
- Page 12 – RTU Hardware Template; To Bottom
- Page 13 – Status LEDs; LED; ON; Troubleshooting; LED Symptom
- Page 14 – Increasing the Number of End-User Systems; This section is reference information.; Function
- Page 16 – Model 5620 RTU Technical Specifications; Item
- Page 17 – Important Safety Instructions
- Page 18 – Declaration of Conformity; Hotwire; Japan; Notices; CE Marking
- Page 19 – Canada EMI Warnings; To Users of Digital Apparatus in Canada:; Notice to Users of the Canadian Telephone Network; If your equipment is in need of repair, refer to
- Page 20 – Warranty; Document Feedback
TM
1
Hotwire
5620 RTU Customer Premises
Installation Instructions
Document Number 5620-A2-GN11-10
June 1999
Before You Begin
The Hotwire
5620 RTU (Remote Termination Unit) interoperates with the Hotwire 8510
DSL Card in the DSLAM (Digital Subscriber Line Access Multiplexer) system.
An optional POTS (Plain Old Telephone Service) splitter is available for the Hotwire
5620 RTU. When a POTS splitter is installed, the telephone and 5620 RADSL (Rate
Adaptive Digital Subscriber Line) RTU can function at the same time over the same pair
of copper wires. In order to confirm the RTU installation, the POTS splitter should be
installed first.
To install a POTS splitter, refer to the appropriate POTS splitter document:
Document Number
Document Title
5030-A2-GN10
Hotwire 5030 POTS Splitter Customer Premises
Installation Instructions
5038-A2-GN10
Hotwire 5038 Distributed POTS Splitter Customer
Premises Installation Instructions
Contact your sales or service representative to order additional product documentation.
Paradyne documents are available on the World Wide Web at www.paradyne.com.
Select
Library
→
Technical Manuals.
Wiring and Cables Needed
The following wiring and standard connectors are used with this product:
New or existing unshielded twisted-pair wiring (CAT3 or better). The CAT3 wiring
must meet EIA/TIA-568 specifications with 24 AWG (.5 mm) or 26 AWG (.4 mm).
Standard RJ11 wall jack.
Standard Ethernet 8-pin, non-keyed modular plug for a PC or workstation. An
Ethernet straight-through or crossover cable is used. Refer to
Installing the Hotwire
5620 RTU, page 8, for Ethernet cable details.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Package Checklist Verify that your package contains the following: - Model 5620 Remote Termination Unit (RTU) - DSL interface cable with RJ11 connectors - Power cord with power transformer Refer to Cables & Connectors, page 14, for standard pin numbers. Be sure to register your warranty at www...
3 97-15346-02 Punchdown Block or NID DSL Jack RTU New Wiring Connections Existing Wiring (POTS) Customer Premises (CP) DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) Demarcation Point Local Loop Hub CP POTS Splitter DSL – Digital Subscriber Line POTS – Plain Old Telephone Service...
4 DSL Access without a POTS Splitter When the Hotwire 5620 RTU is installed without a POTS splitter, a second telephonewiring pair is needed for DSL access. 97-15345-02 Punchdown Block or NID DSL Jack RTU Customer Premises (CP) POTS DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) ...
