Paradyne 5620 - Manuals - manualsarea.com

Page 2 - Package Checklist; What Does the Hotwire 5620 RTU Do?

2 Package Checklist Verify that your package contains the following: - Model 5620 Remote Termination Unit (RTU) - DSL interface cable with RJ11 connectors - Power cord with power transformer Refer to Cables & Connectors, page 14, for standard pin numbers. Be sure to register your warranty at www...

Page 3 - DSL Access with a Hotwire 5038 Distributed POTS Splitter

3 97-15346-02 Punchdown Block or NID DSL Jack RTU New Wiring Connections Existing Wiring (POTS) Customer Premises (CP) DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) Demarcation Point Local Loop Hub CP POTS Splitter DSL – Digital Subscriber Line POTS – Plain Old Telephone Service...

Page 4 - DSL Access without a POTS Splitter; Network

4 DSL Access without a POTS Splitter When the Hotwire 5620 RTU is installed without a POTS splitter, a second telephonewiring pair is needed for DSL access. 97-15345-02 Punchdown Block or NID DSL Jack RTU Customer Premises (CP) POTS DSL Ethernet Crossover Cable Ethernet Cable or Central Office (CO) ...

Page 5 - Installing the DSL Access Wiring; Procedure; Important Safety; Bridge Clip; Punchdown Block; Demarcation Point

5 Installing the DSL Access Wiring The local loop terminates at the punchdown block or NID. Wiring must be connectedfrom the customer premises side of the punchdown block or the NID to an RJ11 jack.Typically, the punchdown block is installed in commercial locations and the NID isinstalled in residen...

Page 7 - RJ11 Wall Jack; or; Wiring can be run from the

97-15300a RJ11 Wall Jack or 7 The Hotwire 5620 RTU connects to the local loop via wiring from the demarcation pointto an RJ11 wall jack. The DSL twisted-pair wiring from the local loop terminates at anew or existing wall jack. It may be necessary to install a standard single RJ11 jack orreplace a si...

Page 8 - Installing the Hotwire 5620 RTU; Hotwire RTU; Customer

8 Installing the Hotwire 5620 RTU Place the Hotwire 5620 RTU on a flat surface with clearance for the rear connectors. Procedure 1. Use the supplied RJ11 6-pin cable for the DSL connection. Insert one end of the cable into the jack labeled DSL. Insert the other end into the wall jack labeled DSL. 97...

Page 11 - Optional RTU Wall Placement

11 Optional RTU Wall Placement The Hotwire 5620 RTU is designed for tabletop placement. The RTU can also bemounted on a wall. To mount an RTU, you will need: - Three slotted-head #6 self-threading screws with molly bolts - Drill and 3/16 ″ drill bit for the molly bolts - Screwdriver A template with ...

Page 12 - RTU Hardware Template; To Bottom

12 RTU Hardware Template Front(LEDs) 98-16171 5.43" 7.55" To Bottom Hole

Page 13 - Status LEDs; LED; ON; Troubleshooting; LED Symptom

13 Status LEDs All of the LEDs turn on and off during the power-on self-test. After a successfulself-test, the LEDs should appear as indicated in BOLD in the Condition column below. LED Condition Status PWR ON RTU has power. ALM OFF ON No active alarms. An alarm condition exists. TST OFF ON No activ...

Page 14 - Increasing the Number of End-User Systems; This section is reference information.; Function

98-15304-01 6-Pin RJ11 Plug DSLCable Pin #1 Pin #6 14 LED Symptom Action DSL and EthernetLEDs are on andthere is no datatransmission. The DSL link and the Ethernet link have been established butthere is no data transmission. If the problem continues, contactthe NSP. Ethernet LED is off. Verify that ...

Page 16 - Model 5620 RTU Technical Specifications; Item

16 Model 5620 RTU Technical Specifications Item Specification * Height x Width x Depth 1.43 ″ x 6.00 ″ x 8.75 ″ (3.64 cm x 15.24 cm x 22.23 cm) Weight 1 lb. 1 oz. (0.48 kg) Power Class 2 Transformer normalservice input voltage range Input: 100 Vac (+10%), 50 Hz; 120 Vac (+10%), 60 Hz; or230 Vac (+10...

Page 17 - Important Safety Instructions

17 ! Important Safety Instructions 1. Read and follow all warning notices and instructions marked on the product or included in the manual. 2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these slots a...

Page 18 - Declaration of Conformity; Hotwire; Japan; Notices; CE Marking

18 Declaration of Conformity This Declaration of Conformity is made by Paradyne Corporation pursuant to Parts 2and 15 of the Federal Communications Commission’s Rules. This complianceinformation statement pertains to the following products: Trade Name: Hotwire Model Number: 5620-A3-200 This device c...

Page 19 - Canada EMI Warnings; To Users of Digital Apparatus in Canada:; Notice to Users of the Canadian Telephone Network; If your equipment is in need of repair, refer to

19 Directive 89/336/EEC – Council Directive of 3 May 1989 on the approximation ofthe laws of the member states relating to Electro-Magnetic Compatibility (EMC), asamended by Directive 93/68/EEC. Canada EMI Warnings ! WARNING: To Users of Digital Apparatus in Canada: This Class B digital apparatus me...

Page 20 - Warranty; Document Feedback

20 Warranty, Sales, Service, and Training Information Contact your local sales representative, service representative, or distributor directly forany help needed. For additional information concerning warranty, sales, service, repair,installation, documentation, training, distributor locations, or P...