Orion 2150XTR - Manual
Orion 2150XTR – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Speaker Plug
Wiring Diagram
2
3
4
1
5
1. -15 Volts
2. Left Input
3. Ground
4. Right Input
5. +15 Volts
DIN Plug Diagram
Technical Brief
:
How to properly set a 2 channel XTR or HCCA
amp with X-over (removable top plate).
Included amps: 250XTR, 275XTR, 2150XTR,
225HCCA, 250HCCA.
80hz High pass
120hz High pass
160hz High pass
200hz High pass
80hz Low pass
120hz Low pass
160hz Low pass
200hz Low pass
SLF-1 Crossover Card Set Up Chart
For questions on this or any other Orion Products, call Technical Support at 1-480-705-5600.
AMP
250XTR
275XTR
2150XTR
225HCCA
POWER
50 X 2
75 x 2
150 x 2
25 x 2
50 x 2
2ohm
2ohm
2ohm
0.5ohm
1ohm
35 amp
60 amp
30 amp
60 amp
Fuse Size
30 amp
Dimensions
11" x 8.5" x 2.25"
12" x 8.5" x 2.25"
12" x 8.5" x 2.25"
18" x 8.5" x 2.25"
18" x 8.5" x 2.25"
S/N
100dB
100dB
100dB
100dB
100dB
0.02%
0.02%
0.02%
THD
0.02%
0.02%
6hz to 30Khz
+/- 0.5dB
Frequency
Response
6hz to 30Khz
+/- 0.5dB
6hz to 30Khz
+/- 0.5dB
6hz to 30Khz
+/- 0.5dB
6hz to 30Khz
+/- 0.5dB
250HCCA
Lowest Recommend
Impedance in Stereo
GAIN
L + R RCA
INPUT
L + R RCA
AUX OUT
DIN
INPUT
Power on LED
ON
1
2
ON
1
2
ON
1
2
2 Bypass cards
= no crossover
(1) SLF-1 + (1) Bypass
= 12dB Slope
(2) SLF-1 Cards
= 24dB Slope
Configuration of Crossover and Bypass Cards
ON
1
2
ON
1
2
ON
1
2
ON
1
2
Jumper configuration #1
Stereo Output.
Jumper configuration #2
Mono Output.
Add these jumpers to
Configuration 1 or 2 for
Full Range from Aux Out.
Configuration for Input Jumpers
Crossover
:
The XTR/HCCA amp includes a SLF-1 crossover
module. The card is adjustable for High pass or
Low pass (see diagram). See diagram below for
installation instructions. If the SLF-1 card is not
used, a Bypass card must be put in it's place or
the amp will not pass signal.
Jumper Configuration:
The configuration of jumpers at the left of the
crossover cards determines the output of the
amp. See the diagram below for set-up
instructions. Configuration #1 is for stereo
operation and Configuration #2 is for mono
operation. To activate the AUXOUT, install the
jumper as shown in configuration # 3. This will
pass full range signal out.
Input Voltage:
The Gain of the XTR/HCCA
amplifier will accept up to 5v of input signal.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
