Page 2 - Before Start; About the Basic Manual; How to use the remote controller
Before Start 2 About the Basic Manual This unit works as an AV controller when connected with a separately sold multichannel power amplifier.The Basic Manual leads you through the initial procedure to enjoy various sources with the AV controller, describing how to make settings and connections, and ...
Page 3 - Connections; Connecting the TV and players; Important; : The power cord must be connected only after all; HDMI cable connection; For how to make settings, see the Advanced Manual.; TV
Step 1: Connections 3 1 Connecting the TV and players Important : The power cord must be connected only after all other connections are completed. HDMI cable connection The unit has many HDMI jacks on its rear panel and each of them corresponds to an input selector button of the same name on the fro...
Page 4 - Connecting Components without HDMI
4 Step 1: Connections the section 6 "Using the multi-zone function" of "Step 3: Playing Back". The unit supports the HDMI Through function that allows transmission from players to the TV even if the unit is in standby. You have to modify the settings to enable the input selection lin...
Page 5 - Connecting speakers; G H; Surround back speakers; GH; Wide speakers; IJ; Using Dolby Enabled Speakers
Step 1: Connections 5 2 Connecting speakers Speaker layout # $ % & ' 7 8 9 G H I J F " To enjoy the Dolby Atmos listening mode, Height 1 speakers, Surround back speakers or Wide speakers need to be installed. " # Front speakers $ Center speaker % & Surround speakers ' Subwoofer 7 8 S...
Page 6 - Combination patterns for Height speakers 1 and 2; Front High; Height speakers 2 cannot be used.; Notes for speaker connection
6 Step 1: Connections Ceiling speakers, etc. are used for maximizing effects in Dolby Atmos or Dolby Surround listening mode. Install Top Front speakers midway between the position just above the listening position and the position just above the front speakers. Install Top Middle speakers just abov...
Page 7 - Connection to the PRE OUT RCA jack
7 Step 1: Connections Connecting a subwoofer with built-in power amplifier The maximum four units of two systems of subwoofer with built-in power amplifier can be connected to this unit. Use the SW1/2 PRE OUT RCA jack or SUBWOOFER 1/2 PRE OUT XLR jack according to the input jack of your subwoofer. Y...
Page 8 - Other connections; Headphones connection; %QPPGEVUVGTGQJGCFRJQPGUYKVJCUVCPFCTFRNWI|KPEJ
8 Step 1: Connections 3 Other connections AM/FM antenna connections Connect the antennas to listen to AM/FM broadcast. When listening to the broadcast for the first time, adjust the antenna position and orientation to get the best reception. AM loop antenna (supplied) Indoor FM antenna (supplied) Fi...
Page 9 - Setting Up; Turning the power on; Firmware update notification; Making the Initial Setup with the Setup Wizard; Read before starting the procedure; st Step : AccuEQ Room Calibration; Place the speaker setup microphone.
9 Step 2: Setting Up Important : When the unit is turned on for the first time, the setup wizard of the section 2 will automatically be launched. If you use the setup wizard to make the initial setup, connect a TV to the HDMI OUT MAIN or SUB jack of the unit via HDMI connection. 1 Turning the power ...
Page 10 - Connect the microphone to the SETUP MIC jack of the unit.; Follow the guidance displayed on the TV screen.; to select the type of subwoofer.; About THX playback; nd Step : Source Connection
10 Step 2: Setting Up 2. After placing the microphone at the measurement position, select "Do it Now" with the cursors and press ENTER. 3. Connect the microphone to the SETUP MIC jack of the unit. SETUP MIC jack Speaker setup microphone 4. Follow the guidance displayed on the TV screen. Accu...
Page 11 - th Step : Network Connection; Make the following preparations.; Select and set the authentication method.; : Enter the password of the access point to; Push Button; : Use the automatic setting button of the; PIN code; : Select this method when the automatic setting; Establish connection.; When the access point is not displayed; WEP method; Exiting the setup wizard
11 Step 2: Setting Up "Yes" with the cursors and press ENTER on the remote controller. Follow the guidance to select the desired REMOTE MODE button and in the keyboard screen, enter the first three characters of the brand name of the device you are going to program (e.g., "ONK" for O...
Page 12 - Playing Back; Playing the player and TV; Remote controller parts name
Step 3: Playing Back 12 1 Playing the player and TV PLAYLIST PLAYLIST SETUP RETURN T V REMOTE MODE / INPUT SELECTOR HOME PREV CH MENU GUIDE TOP MENU RECEIVER SOURCE ZONE 3 2 RED REMOTE MODE SLEEP VOL INPUT ENTER ALBUM CH DISC Q GAME TUNER TV/CD BD/ DVD P C AUX PHONO STB / DVR CBL / SAT MUTING MODE R...
Page 13 - Listening modes; Listening to AM/FM Radio; lj
13 Step 3: Playing Back Listening modes You can select a listening mode from various options such as Dolby Digital, Dolby Atmos and DTS. Select the desired mode by switching and listening actual sound in different modes. The selectable listening modes depend on the format of the input signals. MOVIE...
Page 14 - Pairing
14 Step 3: Playing Back r The SCMS-T content protection method is supported. A Bluetooth-enabled device compatible with the SCMS-T content protection method can be played. r Note that connection is not always guaranteed with all Bluetooth-enabled devices. Pairing Pairing is necessary when using the ...
Page 15 - Using Quick Setup menu
15 Step 3: Playing Back 5 Using Quick Setup menu In the Quick Setup menu, you can set frequently used functions including input selection and volume adjustment. 1. Press Q SETUP on the remote controller. The Quick Setup menu is displayed on the connected TV's screen. CBL/SAT Input Audio Video Inform...
Page 16 - Using the multi-zone function; Types of source you can enjoy in a separate room; Outputting Video/Audio to a Separate Room; Change the setting; : Press RECEIVER and then HOME; b. Connecting a TV in a separate room using
16 Step 3: Playing Back 6 Using the multi-zone function The function allows you to connect the unit with a TV or audio equipment placed in a separate room so that you can enjoy audio and video of the connected equipment even if you are staying in a different room. It is possible to perform playback ...
Page 17 - Listening to Music in a Separate Room; To control on the main unit; WHOLE HOUSE MODE
17 Step 3: Playing Back Listening to Music in a Separate Room c. Connecting an integrated amplifier in a separate room It is possible to play 2 ch source in a separate room while 11.2 ch source is being played in the main room. Connect the PRE/LINE OUT ZONE2 jacks or PRE/LINE OUT ZONE3 jacks of th...
Page 18 - Front Panel; Q R S T
18 Front Panel 1 z ON/STANDBY button : Turns the unit on or into standby mode. 2 PURE AUDIO button and indicator : Switches to the PURE AUDIO mode. 3 Remote control sensor : Receives signals from the remote controller. 4 BLUETOOTH indicator : Flashes while pairing with a Bluetooth-enabled device is ...
Page 19 - Display; fe
19 P DIMMER button (North American model) : Switches the brightness of the display. RT/PTY/TP button (European and Asian models) : Can be used when receiving the station transmitting text information. Q MEMORY button : Registers or deletes a station. R TUNING MODE button : Switches the tuning mode. ...
Page 20 - Rear Panel
20 Rear Panel 1 DIGITAL IN COAXIAL/OPTICAL jacks : Digital audio signals are input. 2 RI REMOTE CONTROL jack : An Onkyo product with RI jack can be connected and synchronized with this unit. 3 ETHERNET port : Used for LAN connection 4 Wireless antenna : Used for Wi-Fi connection or when using a Blue...
Page 21 - Troubleshooting; Before starting the procedure; Not all listening modes use all speakers.; How to reset; How to reset the remote controller
21 Troubleshooting Before starting the procedure Problems may be solved by simply turning the power on/off or disconnecting/connecting the power cord, which is easier than working on the connection, setting and operating procedure. Try the simple measures on both the unit and the connected device. I...
Page 22 - Specifications; r1VJGTU
Specifications 22 Amplifier Section THD+N (Total Harmonic Distortion+Noise) 0.08% (20 Hz - 20 kHz, half power) Input Sensitivity and Impedance (Unbalance) O8Mŝ.+0' O8Mŝ2*101// Rated RCA Output Level and Impedance O8ŝ24'176 Maximum RCA Output Level and Impedance 8ŝ24'176 Rated XLR Output Level and Im...
Page 23 - License and Trademark Information; DISCLAIMER
23 License and Trademark Information Manufactured under license from Dolby Laboratories. Dolby, Dolby Atmos, Dolby Surround, Surround EX and the double-D symbol are trademarks of Dolby Laboratories. For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. D...
Page 24 - Precautions; Declaration of Conformity
Kitahama Chuo Bldg, 2-2-22 Kitahama, Chuo-ku, OSAKA 541-0041, JAPANhttp://www.onkyo.com/ 18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.For Dealer, Service, Order and all other Business Inquiries:Tel: 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/ For Product Support Team Only:1-800-229...
