Omega PCI-DIO96 - Manual - manualsarea.com

Page 4 - INTRODUCTION; Block Diagram

1 INTRODUCTION The PCI-DIO96 is a 96-bit line digital I/O board. The board provides the 96 bits infour 24-bit groups. Each group provides an 8-bit port A and port B, as well as an8-bit port C that can be split into independent 4-bit port C-HI and a 4-bit port C-LO.See Figure 1-1 below. On power up a...

Page 5 - INSTALLATION; CABLES AND SCREW TERMINAL BOARDS

2 INSTALLATION The PCI-DIO96 boards are completely plug-and-play. There are no switches orjumpers on the board. All board addresses are set by your computer’s plug-and-playsoftware. InstaCal is the installation, calibration and test software supplied with your dataacquisition / IO hardware. Refer to...

Page 6 - CONNECTOR DIAGRAM

3.2 CONNECTOR DIAGRAM The PCI-DIO96 I/O connector is a 100-pin type connector accessible from the rear ofthe PC at the expansion backplate See Figure 3-1 below for the board pin out. Figure 3-1. PCI-DIO96 100-Pin Connector Pin Out 3 Port A7 B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 ...

Page 9 - SIGNAL CONNECTION CONSIDERATIONS; IMPORTANT NOTE

3.3 SIGNAL CONNECTION CONSIDERATIONS All the digital inputs on the PCI-DIO96 are 8255 CMOS TTL. The PCI-DIO96output signals are 8255 CMOS. OMEGA Engineering Inc. offers a wide variety of digital signal conditioningproducts that provide an ideal interface between high voltage and/or high currentsigna...

Page 11 - SOFTWARE; UNIVERSAL LIBRARY

4 SOFTWARE We highly recommend that users take advantage of our Universal Library package'seasy-to-use programming interfaces. However, if you are an experiencedprogrammer, and wish to read and write directly to the board, we have provided adetailed register map in the next chapter. 4.1 UNIVERSAL LI...

Page 12 - REGISTER MAPS; Digital I/O registers; Operations; INTCSR Configure

5 REGISTER MAPS The PCI Controller, a PLX-9052, has four configuration, control, and status registers(Table 5-1). They are described in the following section. Table 5-1. I/O Region Register Operations 8-bit byte Digital I/O registers BADR3 N/A N/A BADR2 32-bit double word PCI I/O-mapped config. regi...

Page 19 - 255 Interrupt Source Configure

COUNTER CONFIGURATIONBADR3 + 13 hexREAD/WRITE D0 D1 D2 D3 D4 D5 D6 D7 0 1 2 3 4 5 6 7 This register is used to set the operating modes of each of the 82C54’s counters.Configure the counters by writing mode information to the Configure register,followed by the count information written to the specifi...

Page 20 - Counter Interrupt Source Configure; CTRIR

5.4.7 Counter Interrupt Source Configure BADR3 + 15 hexREAD/WRITE CTR1 CTRIR INTEN X X X X X 0 1 2 3 4 5 6 7 INTEN Enables or disabled interrupts. 1 = enabled, 0 = disabled CTRIR Enables or disables the counters as an interrupt source. 1 = counters maygenerate interrupts. 0 = counters cannot generat...

Page 21 - SPECIFICATIONS; Power Consumption; Counter 3 - Not used

6 SPECIFICATIONS Power Consumption 150 mA max +5V Digital Input / Output User installed. Dual footprint allows pull-up or pull-down configuration Pull-Up/Pull-Down Resistors Input mode (high impedance) Power-up / reset state 0.8 volts max, − 0.5 volts absolute min Input Low 2.0 volts min, 5.5 volts ...

Page 23 - ELECTRONICS AND INTERFACING

7 ELECTRONICS AND INTERFACING This brief introduction to the electronics most often needed by digital I/O board userscovers a few key concepts. IMPORTANT NOTE WHENEVER AN 82C55 IS POWERED-ON OR RESET, ALLPINS ARE SET TO HIGH-IMPEDANCE INPUT. FOLLOWINGSTANDARD TTL FUNCTIONALITY, THESE INPUTS WILLTYPI...

Page 24 - UNCONNECTED INPUTS FLOAT; TTL TO SOLID STATE RELAYS

If the board is in output mode, the board has enough power to override thepull-up/down resistor's high signal and drive the line to 0 volts. If the output circuitasserts a high signal, the pull-up resistor guaranties that the line goes to +5 V. Of course, a pull-down resistor accomplishes the same t...

Page 25 - The formula for voltage attenuation is: Figure 7-2. Voltage Divider

The most convenient way to use solid state relays and a PCI-DIO96 board is to use aSolid State Relay Rack. An SSR Rack is a circuit board with input buffer amplifiersthat are powerful enough to switch the SSRs. The buffer amplifiers and SSRs aresocketed. The standard buffer amplifiers are inverting ...

Page 27 - For Your Notes

Page 30 - EC Declaration of Conformity; Description

EC Declaration of Conformity Description Part Number Digital I/O board PCI-DIO96 to which this declaration relates, meets the essential requirements, is in conformitywith, and CE marking has been applied according to the relevant EC Directives listedbelow using the relevant section of the following ...

Omega PCI-DIO96 - Manual

Table of Contents:

Summary

Other Omega Models