Omega DPF500 Series - Manual

Page 2 - One Omega Drive, River Bend Technology Centre; OMEGAnet

Servicing North America: U.S.A.: One Omega Drive, P.O. Box 4047 ISO 9001 Certified Stamford, CT 06907-0047TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: [email protected] Canada: 976 BergarLaval (Quebec) H7L 5A1, CanadaTEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: [email protected] For immediate technic...

Page 6 - Chapter 2 Installation; SAVE; Rear View; Battery; Connector

2 Chapter 2 Installation 2.1 Battery Installation: All DPF500 models are shipped without the battery(ies) installed. This preserves battery life when the unit is not in service. When using external DPF5-BP, mount within 12" and plug connector into 3 position square posts (see Fig 1). Polarity is...

Page 7 - Panel

3 DPF503 DPF502 DPF501 DPF5-BP Accessory 2.3 Dimensions Dimensions are in inches (mm) Dimensions are in inches (mm) Dimensions are in inches (mm) Dimensions are in inches (mm) 4.92 (125) 4.33 (110) 4.33 (110) #8 Screw Mounting holes molded directly under cover screws. Max. screw head .29" (Typ. ...

Page 8 - used so long as proper polarity is observed.; Caution; eration of the analog output and/or excessive current fl ow.; Typical Applications / Wiring Diagrams; MAG INPUT / DC POWERED

4 Several typical applications of the DPF500 are shown below. Please observe that the various pulse inputs and power options may be intermixed in many ways to solve common applications. The isolated pulse output may be freely used so long as proper polarity is observed. Caution : When 4-20 mA loop o...

Page 9 - puted based upon the K-Factor for that measurement sample.; Chapter 4 Programming

5 Chapter 3 20 Point Linearization (-LIN option) 3.1 20 Point Linearization Operation (-LIN option) A 20 point linearization table is used to construct a curve describing the relationship of K-Factor and input frequency. The measured input frequency is used to access the table. A linear interpolatio...

Page 10 - Explanation of Display Prompts

6 4.1 Explanation of Display Prompts (continued) fr# : (frequency for point #) This prompt will only appear when 20 point selected. It sets the frequency for each of the 20 points (#). Press the ↑ key to increment each digit. Press the ← key to step to the next digit to the left. Press the E key to ...

Page 11 - Record this number for later use!

7 4.1 Explanation of Display Prompts (continued) oUt HI : (out high) Sets the high setting for the 4-20 mA analog output. Key in the high rate value at which the unit will output 20 mA. Press the ↑ key to increment each digit. Press the ← key to step to the next digit to the left. Press the E key to...

Page 12 - Programming Flowchart; RATE; Continue On; YES; SET pnts; M key; linear; FAC

8 4.2 Programming Flowchart RATE RA RA TOTAL CLR ToT FDEC 12345678 M RUN MODE CLEAR TOTAL OT OT FACTORDECIMAL FAC 100 FACTOR 0000 ent Code ENTER CODE If panellock ON If panellock OFF If codecorrect If codeincorrect FAC 20poInt FACTORTYPE 20poInt lInear lInear selected E M E E M E M E M 20poInt selec...

Page 13 - This will only display on units with Analog Output.; TDEC; Continued From Previous Page; yes

9 4.2 Programming Flowchart (continued) Press the key to step the totalizer decimal to the desired location. Press the E key to enter the displayed decimal location. Press the M key to skip and keep the existing location Press the key to step to the desired totalizer descriptor. Press the E key to e...

Page 14 - Chapter 5 Operation; Once properly wired, the operation of the DPF500 is automatic.

10 Chapter 5 Operation 5.1 General A suitable pulse producing device or ﬂ ow meter is wired to one of the three pulse inputs provided on the DPF500. Only one of these inputs is used in a given application. There are no connections to the two unused pulse inputs. Isolated magnetic pickups may be conn...

Page 15 - If the unit is equipped with the analog output option,

11 Chapter 6 Error Messages / Analog Output Calibration 6.1 Error Messages The DPF500 is provided with extensive self checking which assists the user in the location of setup entry errors and in reporting malfunctions or unusual operating conditions. When an error occurs, the display will ﬂ ash. Pre...

Page 16 - Chapter 7 Specifi cations

12 Chapter 7 Speciﬁ cations ENVIRONMENTAL: OPERATING TEMPERATURE -4°F (-20°C) to + 158°F (70°C) Extended Temp: -22°F (-30°C) to + 158°F (70°C) HUMIDITY 0 - 90% Noncondensing MOUNTING STYLES: 1 - Panel Mount - NEMA 4X Front 2 - Wall Mount - NEMA 4X Enclosure (keypad mounted behind clear cover) 3 - Ex...

Page 17 - RETURN REQUESTS/INQUIRIES; WARRANTY; OMEGA is a registered trademark of OMEGA ENGINEERING, INC.

WARRANTY/ DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for aperiod of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping...

Page 18 - Shop online at omega.com

M 1896 / 07 05 Where Do I Find Everything I Need for Process Measurement and Control? OMEGA…Of Course! Shop online at omega.com TEMPERATURE Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies Wire: Thermocouple, RTD & Thermistor Calibrators & Ice Point References R...

Omega DPF500 Series - Manual

Table of Contents:

Summary

Other Omega Models