Page 2 - About this User’s Manual; Chapter 1. Introduction; Online Upgrade
1 About this User’s Manual This User’s Manual gives users basic steps on installation and operation. Please read this manual chapter by chapter. Chapter 1. Introduction Introduce the IP Telephony Gateway to users in terms of feature, appearance, and application. Chapter 2. Startup Help user complete...
Page 3 - Table of Content
2 Table of Content 1. .. Introduction .............................................................................................. 4 1.1 Key Features ................................................................................................ 4 1.2 Physical Description ...........................
Page 6 - Physical Description; LED Indicators; LED
5 1.2 Physical Description SP5008A: SP5008A Front Panel SP5058A SP5058A Front Panel SP5018A SP5018A Front Panel LED Indicators LED Status Description POWER On / Green The Power is on READY Blink / Green Booting up for self test Blink / Green Gateway reg. fails PROXY Constant / Green Gateway reg. suc...
Page 7 - RESET; Factory default button. Press and hold for 5 seconds to reset; WAN
6 1*. SP5008A: FXS = T1 - T8 SP5018A: FXS = T1 - T4, FXO = L1 - L4 SP5058A: FXO = L1 - L8 SP5008A SP5008A Rear Panel SP5058A SP5058A Rear Panel SP5018A SP5018A Rear Panel --------------------------------------------------------------------------------------------------- RESET Factory default button....
Page 8 - Login into the System; root
7 2. Startup 2.1 Login into the System First of all, connect your computer to MICRONET SP5008A / SP5018A / SP5058A’s LAN port by using DHCP. The IP address assign to your computer should be 192.168.123.x by default. Once you can get the IP address from MICRONET SP5008A / SP5018A / SP5058A, you can s...
Page 10 - Network Configuration; access with PCs. Go to; address of the WAN port.
9 2.2 Network Configuration By default, the gateway is in NAT mode (router mode) and can share Internet access with PCs. Go to [ Network Configuration / WAN Setting ] , and configure WAN setting according to actual condition. In default IP type of DHCP client, it requests necessary IP information fr...
Page 11 - WAN Setting; Item
10 WAN Setting Item Description Static IP DHCP PPPoE Connected mode Select the connection method for the WAN port of the SP5008A/SP5018A/SP5058A, you can choose the following: z Static IP z DHCP z PPPoE V V V Current IP Address Show current IP address V V V DNS server mode Select the DNS behavior, y...
Page 12 - the; “Apply”
11 Item Description Static IP DHCP PPPoE Default gateway Specify the IP address of the default gateway. V Remote access restriction Restricts/Blocks users connecting to the WAN port’s IP remotely, you can Enable/Disable this option. V V V PPPoE userID Specify the username of the PPPoE account V PPPo...
Page 13 - Reboot; ” button to apply the changes.; “Reboot”; button to apply the changes.; before use PC to connect to LAN port.
12 2. Press the “ Reboot ” button to apply the changes. 2.2.2 DHCP 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes. ----------------------------------------------------------------------------------------------------- No...
Page 17 - General configuration; instructions explained below.; PABX Connection; To enable PABX behavior or not.; SIP Setting; It is used (Yes) when you only have 1 SIP account and
16 2.3 General configuration To make VoIP calls, you will need a SIP account provided by the SIP Proxy you are registered with. To configure the relevant SIP settings, please refer to the instructions explained below. 2.3.1 PABX Mode (SP5018A only) This quick setting is used for MICRONET SP5018A to ...
Page 18 - Primary FXS SIP settings; When you have multiple SIP accounts for each FXS line,; FXO Dialing Prefix; When the prefix is set here, the call will be route to FXO
17 3.3.2.1 Primary FXS SIP settings When you have multiple SIP accounts for each FXS line, please set Representative Number Only to No. Then refer to 3.3.2.1 for the detail FXO Dialing Prefix When the prefix is set here, the call will be route to FXO instead of VOIP.
Page 19 - Appendix A
18 2.3.2 SIP Setting Primary proxy/P2P IP Specify the data of primary proxy : Enable/Disable, IP address, Port#, Domain Name, Expire time and MWI TTL. The P2P mode will be explained in paragraph Appendix A Secondary proxy Specify the data of secondary proxy: Enable/Disable, IP address, Port#, Domain...
Page 20 - address and Port fields. Press the; button to save changes.
19 Register or Unregister to SIP Proxy Account Input the SIP Proxy registration account ID. Number Input the phone number. Password Input the password of IP Proxy registration account ID. Display name Specify the Display name of the phone number Forward Specify the Representative forwarding type to ...
Page 21 - Web Administration; General configuration; Session Refresh Request
20 3. Web Administration 3.1 General configuration 3.1.1 SIP Advanced Setting Local SIP port (1~65535) Specify the local SIP port’s number. Local RTP port (1~65535) Specify the local RTP port’s number. Session Expire (Sec) Specify the session expire time that will be used to negotiate with the remot...
Page 23 - Specify the Modem by pass payload type (range is; Modem relay payload type; Specify the Modem relay payload type (range is
22 3.1.2 Payload Type Setting RFC2833 payload type Specify the RFC2833 payload type (range is 96~128, however 100, 102~105 is reserved by other payload types). T.38 FAX payload type Specify the FAX payload type (range is 96~128, however 100, 102~105 is reserved by other payload types) T.38 Redundanc...
Page 29 - Speed Dial; Speed Dial Editor; then press the Add or Del button to add or delete record
28 3.1.5 Speed Dial Setting Speed Dial Speed Dial Editor Specify the speed Dial Number/Telephone Number/Name, then press the Add or Del button to add or delete record
Page 30 - Peer to Peer call; You can use speed dial to do the peer to peer call as follows:; Specify the speed Dial Number/Telephone
29 Peer to Peer call You can use speed dial to do the peer to peer call as follows: Speed Dial Editor (In P2P application) Specify the speed Dial Number/Telephone Number/Name, then press the Add or Del button to add or delete record The format of “Telephone Number” is “#@ip address: port”, for examp...
Page 32 - The default symbol is C.; Press the
31 The default symbol is C. 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes.
Page 37 - Advanced Configuration; prack
36 3.2 Advanced Configuration 3.2.1 System setting prack PRACK is defined in RFC 3262: Reliability of Provisional Responses in SIP. You can accommodate your softswitch (Proxy Server) to Enable or Disable this feature. ROH (FXS only) Receiver-Off-Hook (ROH) Tone A ROH tone is sent to the subscriber t...
Page 40 - ping ip to keep alive network; Specify the IP for pinging to make sure the
39 The default setting is “Disable”, if you are not using this particular special application mentioned above, please do not enable this function. ping ip to keep alive network Specify the IP for pinging to make sure the network keeps alive. ping timer(sec) Specify the interval of ping timer(sec) 1....
Page 41 - SNTP mode; Select the SNTP mode : On or Off; SNTP server address; Specify the SNTP server address for time synchronization.; Time setting; /second when you select the SNTP mode with “Off”.
40 3.2.2 SNTP Setting SNTP mode Select the SNTP mode : On or Off SNTP server address Specify the SNTP server address for time synchronization. Time Zone -GMT Select the Time Zone of your location Time setting You can specify the time with year/month/date /hour/minute /second when you select the SNTP...
Page 44 - You can set this option for each of the 8 lines.; button (at the bottom) after you finish to save
43 You can set this option for each of the 8 lines. 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” button to apply the changes.
Page 46 - Disconnect tone 2; Specify the pattern of the disconnect tone for disconnect
45 NOTE: If the disconnect tone only has single frequency, please set it to low frequency. If the disconnect tone only has single cadence, please set it to Tone 1. Disconnect tone 2 Specify the pattern of the disconnect tone for disconnect tone 2 (second set), you can adjust the high frequency, low ...
Page 50 - FXO Dial Prefix; For outgoing call, the default will be made to VOIP.
49 FXO Dial Prefix For outgoing call, the default will be made to VOIP. However, if you set the FXO prefix here, the call will be route to FXO instead of VOIP. It can be applied to FXO model only. 1. Press the “Apply” button (at the bottom) after you finish to save changes. 2. Press the “Reboot” but...
Page 53 - Provision server Mode; Enable/Disable provision function; Provision server IP address; Specify the Provision Server’s IP address.; Provision server port; Specify the Provision server port; Provision cycle time; Specify a scheduled time in a day
52 3.3 Management 3.3.1 Provision Server Note: If you need this requirement, Please contact MICRONET for availabilities. Provision server Mode Enable/Disable provision function Provision server IP address Specify the Provision Server’s IP address. Provision server port Specify the Provision server p...
Page 54 - Export File; Click the “Export” button to export “user.cfg” data; Import File; Specify the file path and file name to Import the configure
53 3.3.2 Save-Reload setting Export File Click the “Export” button to export “user.cfg” data Import File Specify the file path and file name to Import the configure data. Press the “Reboot” button to apply the changes.
Page 56 - Updating the firmware by FTP; Select FTP mode in the drop down list.
55 Updating the firmware by FTP 1. Select FTP mode in the drop down list. 2. Key in the IP address, login name, password of your FTP server and specify the correct filename of the firmware. 3. Press the Start button (next to the Target file name text box) to execute the upgrade process. 4. Please wa...
Page 57 - Updating the firmware by TFTP; is stored. Now, leave the TFTP program running and switch back to the
56 Updating the firmware by TFTP 1. First, download the TFTP program from our website. Unzip the TFTP to a directory that you desire in your hard drive and execute the TFTP program. Make sure that the TFTP program points to the directory of where your firmware is stored. Now, leave the TFTP program ...
Page 59 - changed when this feature is executed.
58 3.3.4 Reset to Default Users can restore back to factory default settings using this feature. The password of the account and the network configurations are the things that will not be changed when this feature is executed.
Page 61 - Boot version; Displays the current boot version loaded on the MICRONET; Post version; Displays the current post version loaded on the MICRONET; Application version; Displays the current application version loaded on the
60 3.3.6 Version Info. Boot version Displays the current boot version loaded on the MICRONET SP5008A / SP5018A / SP5058A. Post version Displays the current post version loaded on the MICRONET SP5008A / SP5018A / SP5058A. Application version Displays the current application version loaded on the MICR...
Page 62 - Displays the corresponding port number.; Status; Displays the status of the port.; Port Type; Displays the registration status of the corresponding port
61 3.3.7 Port Status Item Displays the corresponding port number. Status Displays the status of the port. Port Type Displays the port type (FXS,FXO)of the corresponding port number. Register Proxy Displays the registration status of the corresponding port number. if the port Register success it will...
Page 64 - Rebooting the system
63 3.4 Rebooting the system Executing this function will reboot the whole system, when configuration changes are made to the device, it needs to be rebooted for the changes to take effect (see figure below).
Page 65 - Operation; same PABX in two or more branches.; General Configuration / SIP Setting; Primary proxy/P2P IP; Specify the destination (Side B) IP Address of; Call number configuration
64 4. Operation 4.1 Peer to Peer mode (FXO to FXS) In this application, the distance of PABX extension is not limited. You can use the same PABX in two or more branches. Configuration: 1. Side A (FXO): IP address: 10.1.1.2, number is 2000 to 2008 2. Side B (FXS): IP address: 10.1.1.3, number is 1000...
Page 66 - General Configuration / Line Setting; Please refer to the figure shown above,; Enable; and; Disable all the register.; password and display name.
65 Side A : (SP5058A : IP address 10.1.1.2) General Configuration / Line Setting Line 1~Line 8 (Side A -- FXO) Please refer to the figure shown above, Enable all the line and Disable all the register. Specify the relevant data: Account, number, password and display name. 1. Press the “Apply” button ...
Page 67 - General Configuration—SIP Setting; Specify the destination (Side A) IP Address of
66 Side B: (MICRONET SP5008A : IP address 10.1.1.3) General Configuration—SIP Setting Primary proxy/P2P IP (Side B) Specify the destination (Side A) IP Address of Peer to Peer mode, and specify the port# with 5076 Call number configuration Representative number (Side B) Enable the representative lin...
Page 68 - Disable all the register and call; password and display name
67 Side B: (MICRONET SP5008A: IP address 10.1.1.3) General Configuration / Line Setting Line 1~Line 8 (Side B) Please refer to the figure shown above, Enable all the line and Disable all the register and call waiting. Specify the relevant data: Account, number, password and display name 1. Press the...
Page 73 - Specification; Security
72 5. Specification Model SP5008A Standard SIPv2 (RFC 3261): Primary and Secondary Proxy, Primary and Secondary Outbound Proxy POTS Interface 8 FXS Ethernet Port z 1 x RJ-45 WAN port of 10/100M z 4 x RJ-45 LAN ports of 10/100M Voice z Codec: G.711a/mu-law, G.723.1 (6.3K), G.729, G.729.A z VAD, CNG, ...
