Page 2 - Warnings; POWER
Warnings WARNING : To prevent fire or shock hazard, do not expose the set to rain or moisture. Do not rubor strike the Active Matrix LCD with anything hard as this may scratch, mar, ordamage the Active Matrix LCD permanently.The appliance is not intended for use by young children or infirm persons w...
Page 3 - Service
22 3 Warnings Service Never remove the back cover of the TV, this can expose you to high voltage andother hazards. If the TV does not operate properly, unplug it and call your nearestNEC Service Centre.Connect the antenna cable to the connection marked Ant. (on the rear). For bestreception, use an o...
Page 4 - Contents
Contents Warnings 2~3 Contents 4 Supplied Accessories 5 Controls 6~8 Controller of panel 6 Remote controller 7~8 Basic Operation 9 Turning the TV On and Off 9 Programme selection 9 Volume adjustment 9 Q.View 9 Sound mute function 9 On screen Language selection 9 On Screen Menus and Displays 10 Setti...
Page 5 - Supplied Accessories
22 5 Supplied Accessories L Make Sure the following accessories are provided with Product. 2. Remote controller 4. Owner’s manual 5. PC IN cable 6. PC Audio IN cable 3. Batteries (type AAA) 1. AC Cord 32 inch 32 " TFT LCD TV NLT-32W
Page 6 - Controls
6 Controls 1. PC DIGITAL IN (DVI-I)2. H/P (Headphone out) Connect a headphone to this socket. 3. PC AUDIO IN Connect the audio cable from the PC to the PC AUDIO IN of the set. 4. PC ANALOG IN (D-SUB)5. COMPONENT IN6. DTV IN7. AV-IN8. AV-OUT9. S-VIDEO IN Connect the output of the S -VIDEO on the VCR ...
Page 7 - Remote controller; xy
22 7 Controls All the functions can be controlled with the remote controller. Some functions canalso be adjusted with the buttons on the side panel of the set. Remote controller Before you use the remote controller, please install the batteries. 1. POWER Turns the TV on from standby or off to standb...
Page 8 - Battery installation; Ïq; TELETEXT buttons
22 8 Controls → → Battery installation u Inserting batteries 1. Remove the battery cover by pulling it upward in the direction shown by the arrow. 2. Insert the batteries with correct polarity ( "+" to "+", and "-" to "-" ). 3. Replace the battery compartment cover. *...
Page 9 - Basic Operation
22 9 Turning the TV On and Off Standby Setup: The AC power cord must be set up andconnected to have the TV in standby mode ready to be turnedon. Press the ON/OFF button on the side panel of the TV to go into standby mode. 1. If the TV is in standby mode, press the POWER button on the remote controll...
Page 10 - On Screen Menus and Displays
22 10 On Screen Menus and Displays 1. Press the MENU button to display main menu. 2. Press the PR xy button to select menus-Picture, Sound, Special, Setup. 3. Adjust each menu with the VOL Ïq button. 4. Press the MENU button to return to preceding menu. 5. Press the TV/AV button to finish adjusting ...
Page 11 - Setting up TV Programme
22 11 Setting up TV Programme Once you have preset the programmes, you will be able touse the PR xy or NUMBER buttons to scan the programmes you programmed.Programmes can be tuned using automatic or manualmodes. Auto Programme All programmes that can be received are stored by thismethod. It is recom...
Page 14 - Picture Control; Auto Picture Control; Dynamic; Manual Picture Control
Note. In PC mode, PSM function isn’t available. 14 Picture Control You can adjust picture Contrast , Brightness , Colour , Sharpness and Tint (only in NTSC mode) to the levels you prefer. Auto Picture Control *The Picture options - Dynamic, Standard, Mild and Gameare programmed for good picture repr...
Page 15 - Sound Control
22 15 Sound Control You can select your preferred sound setting; Flat , Music , Movie or Speech . You can also adjust the sound frequency of equalizer, balance. If you switch AVL to on, the set automatically keeps on an equal volume level evenif you change programmes. 1. Press the MENU button. 2. Se...
Page 16 - Auto Sound Control; Flat
Sound Control 16 Auto Sound Control * The sound Flat , Music , Movie and Speech are programmed for good sound reproduction at the factory and cannot be changed. SSM (Sound Status Memory) 1. Press the SSM button. 2. Press the SSM button repeatedly to select. Each press of the button changes the scree...
Page 17 - Other functions; Clock
22 17 Other functions You can control other functions; Clock , Blue Back , Auto Sleep , Childlock , Radio and ARC menu. Clock Setting the clock is necessary in order to use the various timer features of the TV. You can set automatic TV On or Off time. 1. Press the MENU button. 2. Press the PR xy but...
Page 18 - Auto Sleep
Other functions Auto Sleep If you select Auto Sleep On the set will automatically switch itself to standby mode approximately ten minutes after a TV Channel stops broadcasting.1. Press the MENU button. 2. Select the Special menu, then press VOL Ïq . 3. Press the PR xy button to select Auto Sleep . 4...
Page 19 - Radio Control
19 Radio Control This function is possible only when the set is in Radio mode.(Radio mode is displayedwhen the Setting for special menu is radio On.) 1. Use TV/AV button on remote controller to select Radio mode . 2. Press the MENU button to set Radio Setup menu. 3. Press the VOL Ïq button repeatedl...
Page 20 - Calling the programme list; Displaying programme list; Paging through a programme list
20 Other functions Calling the programme list You can check the programmes stored in the memory by displaying the programme LIST. Displaying programme list 1. Press the LIST button to display the Programme list menu. The programme list appears on the screen.One programme list contains ten programmes...
Page 21 - TELETEXT; TEXT; TOP text
22 21 TELETEXT TEXT On/Off Press the TEXT/MIX button to switch to TELETEXT. The initial page or last selected page appears on the screen. The first page number indicates your selection, while the second shows the current page displayed. 1. Press TEXT/MIX button once, displays the Teletext pages. If ...
Page 22 - Special TELETEXT functions; Functions
TELETEXT Special TELETEXT functions Changes Teletext mode Only Teletext mode, text mode superimposed on theTV picture, TV mode Selects double height text.Press this button to enlarge the top half of the page.Press this button again to enlarge the bottom half ofthe page.Press this button again to ret...
Page 23 - DTV Input; External Equipment Connection
23 Antenna connection 1. Connect RF out on the VCR to the Antenna input on the rear of the TV. 2. Connect the antenna cable to the antenna in jack on the VCR. 3. Use the TV/AV button to select TV mode.4. Press the PLAY button on the VCR. COMPONENT INPUT 1. device to the COMPONENT on the TV.2. Use th...
Page 24 - Headphone jack
22 External Equipment Connection A/V INPUT 1. Connect the A/V out jacks on of the VCR to A/V-In jacks on the TV. 2. Press the TV/AV button to select VIDEO mode. 3. Press the PLAY button on the VCR. The VCR playback picture appears on the screen. Note : If you have a mono VCR, connect the audio cable...
Page 25 - Connecting the PC as a monitor; Picture adjustment
22 25 Connecting the PC as a monitor This function is possible only when the set is in PC mode.Use the TV/AV button on remote controller. Picture adjustment You can adjust picture Contrast , Brightness , Temperature , Clock , Phase and ARC as you prefer. 1. Press the TV/AV button to select the PC mo...
Page 26 - Sound adjustment
Connecting the PC as a monitor Sound adjustment 1. Press the MENU button. 2. Select the Sound menu, then press VOL Ïq . 3. Press the PR xy button to select the desired sound item; Equalizer, Balance, AVL, Surround or Sound Mode . 4. Press the VOL Ïq button to make desired adjustment. 5. Press the VO...
Page 27 - Auto; Reset
27 Connecting the PC as a monitor Auto This function is for the automatic adjustment of the screen position, clock andclock phase. The displayed image will disappear for a few seconds while theAuto-configuration is in process. Note: Some signal from some graphics boards may not function properly. If...
Page 29 - Product Specifications; Model
22 29 Product Specifications Model NLT-32W Main body Horizontal size 960(960) mm Thickness 109(222) mm (With stand) Height 513(565.5) mm Weight 17.6(19.3) kg Television system PAL-BG, I, DK / SECAM-BG, DK, / NTSC-M Television programme VHF: 0~12 UHF :21~69 Cable : S1~S41 LCD Panel 32" WIDE TFT L...
Page 30 - Troubleshooting; Check item
Troubleshooting No picture on screen and no soundfrom speakers No picture/No picture from AVterminal Picture is displayed, but no soundfrom the speakers. Picture is too light There are stripes on the screen orcolors fade. Picture is too dark. Remote control does not work. The picture is not sharp.Th...
Page 31 - NEC Service Centres; New South Wales
22 31 NEC Australia Pty. Ltd. ABN 86 001 217 527 Home Electronics Group NEC Service Centres New South Wales Sydney 184 Milperra Rd, Revesby 2212 131-632 Newcastle 120 Parry Street, Newcastle West 2302 131-632 Victoria Melbourne Unit1/6, Garden Road, Clayton, 3168 131-632 Queensland Brisbane Unit 4/3...
