Page 3 - Warnings; POWER
Warnings WARNING : To prevent fire or shock hazard, do not expose the set to rain or moisture. Do not rubor strike the Active Matrix LCD with anything hard as this may scratch, mar, ordamage the Active Matrix LCD permanently.The appliance is not intended for use by young children or infirm persons w...
Page 5 - Contents
22 5 Contents Warnings 3~4 Contents 5 Supplied Accessories 6 Controls 7~9 Controller of panel 7 Remote controller 8~9 Basic Operation 10 Turning the TV On and Off 10 Programme selection 10 Volume adjustment 10 Q.View 10 Sound mute function 10 On screen Language selection 10 On Screen Menus and Displ...
Page 6 - Supplied Accessories
6 Supplied Accessories L Make Sure the following accessories are provided with Product. 1. AC Cord 2. Remote controller 4. Owner’s manual 5. PC IN cable 6. PC Audio IN cable 3. Batteries (type AAA) 23 inch 23 " TFT LCD TV NLT-23WQ User's Manual
Page 7 - Controls
22 7 Controls 1. PC DIGITAL IN (DVI-D)2. PC ANALOG IN (D-SUB)3. A/V OUTConnect these outputs to the Audio/Video inputs of external equipment. 4. A/V IN1Connect the Audio/Video outputs of external equipment to these inputs.5. COMPONENT2/DTV2 6. COMPONENT1/DTV17. S-VIDEO INConnect the output of the S ...
Page 8 - Remote controller; xy
22 Controls All the functions can be controlled with the remote controller. Some functions canalso be adjusted with the buttons on the side panel of the set. Remote controller Before you use the remote controller, please install the batteries. 1. POWER Turns the TV on from standby or off to standby ...
Page 9 - Battery installation; Ïq; TELETEXT buttons
22 9 Controls → → Battery installation u Inserting batteries 1. Remove the battery cover by pulling it upward in the direction shown by the arrow. 2. Insert the batteries with correct polarity ( "+" to "+", and "-" to "-" ). 3. Replace the battery compartment cover. *...
Page 10 - Basic Operation
22 Turning the TV On and Off Standby Setup: The AC power cord must be set up andconnected to have the TV in standby mode ready to be turnedon. Press the ON/OFF button on the front panel of the TV to gointo standby mode. 1. If the TV is in standby mode, press the POWER button on the remote controller...
Page 11 - On Screen Menus and Displays
22 11 On Screen Menus and Displays 1. Press the MENU button to display main menu. 2. Press the PR xy button to select menus-Picture, Sound, Special, Setup. 3. Adjust each menu with the Ïq button. 4. Press the MENU button to return to preceding menu. 5. Press the TV/AV button to finish adjusting menu...
Page 12 - Setting up TV Programme
Setting up TV Programme Once you have preset the programmes, you will be able touse the PR xy or NUMBER buttons to scan the programmes you programmed.Programmes can be tuned using automatic or manualmodes. Auto Programme All programmes that can be received are stored by thismethod. It is recommended...
Page 15 - Picture Control; Auto Picture Control; Dynamic; Manual Picture Control
22 15 Picture Control You can adjust picture Contrast, Brightness, Colour, Sharpness and Tint(only inNTSC mode) to the levels you prefer. Auto Picture Control *The Picture options - Dynamic, Standard, Mild and Gameare programmed for good picture reproductionat the factory and cannot be changed. PSM ...
Page 16 - Sound Control
Sound Control You can select your preferred sound setting; Flat, Music, Movie or Speech. You can also adjust the soundfrequency of equalizer, balance. If you switch AVL to on,the set automatically keeps on an equal volume level evenif you change programmes. 1. Press the MENU button.2. Select the Sou...
Page 17 - Auto Sound Control; Flat
Sound Control 22 17 Auto Sound Control * The sound Flat, Music, Movie and Speech are programmed for good sound reproduction at the factory and cannot be changed. SSM (Sound Status Memory) 1. Press the SSM button. 2. Press the SSM button repeatedly to select. Each press of the button changes the scre...
Page 18 - Other functions; Clock; Blue Back
18 Other functions You can control other functions; Clock, Blue Back, AutoSleep, Childlock and ARC menu. Clock Setting the clock is necessary in order to use the various timer features of the TV. You can set automatic TV On or Off time. 1. Press the MENU button.2. Press the PR xy button to select th...
Page 19 - Auto Sleep; Childlock
Other functions 19 Auto Sleep If you select Auto Sleep On the set will automatically switch itself to standby mode approximately ten minutes after a TV Channel stops broadcasting.1. Press the MENU button.2. Select the Special menu.3. Press the PR xy button to select Auto Sleep. 4. Press the Ïq butto...
Page 20 - Calling the programme list; Displaying programme list; Paging through a programme list
20 Other functions Calling the programme list You can check the programmes stored in the memory by displaying the programme LIST. Displaying programme list 1. Press the LIST button to display the Programme list menu. The programme list appears on the screen.One programme list contains ten programmes...
Page 21 - TELETEXT; TOP text
22 21 TELETEXT TEXT On/Off Press the TEXT/MIX button to switch to TELETEXT. The initial page or last selected page appears on the screen. The first page number indicates your selection, while the second shows the current page displayed. 1. Press TEXT/MIX button once, displays the Teletext pages. If ...
Page 22 - Special TELETEXT functions; Functions
TELETEXT Special TELETEXT functions Changes Teletext mode.Only Teletext mode, text mode superimposed on theTV picture, TV mode. Selects double height text.Press this button to enlarge the top half of the page.Press this button again to enlarge the bottom half ofthe page.Press this button again to re...
Page 23 - Antenna connection; External Equipment Connection
23 Antenna connection 1. Connect RF out on the VCR to the Antenna input on the rear of the TV. 2. Connect the antenna cable to the antenna in jack on the VCR. 3. Press the TV/AV button to select Antenna Input source. 4. Press the PLAY button on the VCR. COMPONENT1/DTV1 or COMPONENT2/DTV2 INPUT 1. Co...
Page 24 - Headphone jack
22 External Equipment Connection Headphone jack Insert the headphone plug to the headphone jack on the TV. You can listen to thesound through the headphone; no sound from the speaker on the TV. To adjust theheadphone volume, press the Ïq button. If you press the MUTE button, the sound from the headp...
Page 25 - Connecting the PC as a monitor
22 25 Connecting the PC as a monitor DVI (Digital Visual Interface) INPUT 1. Connect the DVI of PC to the DVI input on the TV.2. Select PC-Digital mode by pressing the TV/AV button repeatedly. (When DVI source is connected, TV/AV mode converts PC to DVI mode.) Note:a. If the set is cold, there may b...
Page 26 - Picture adjustment
26 Connecting the PC as a monitor This function is possible only when the set is in PC mode.Use the TV/AV button on remote controller. Picture adjustment You can adjust picture Contrast, Brightness,Temperature, Clock, Phase and ARC as you prefer. 1. Press the TV/AV button to select the PC mode.2. Pr...
Page 27 - Sound adjustment
Connecting the PC as a monitor Sound adjustment 1. Press the MENU button.2. Select the Sound menu, then press the VOL q button. 3. Press the PR xy button to select the desired sound item; Equalizer, Balance, AVL, Surround or Sound Mode. 4. Press the Ïq button to make desired adjustment. 5. Press the...
Page 28 - Position Adjustment
28 Connecting the PC as a monitor Position Adjustment This function is to adjust picture to left/right and up/down as you prefer. 1. Press the MENU button.2. Select the H/V Position menu.3. Press the PR xy button to select the desired position item. 4. Press the Ïq button to adjust horizontal positi...
Page 29 - Product Specification; Model
22 29 Product Specification Model NLT-23WQ Main body Horizontal size 600 mm Thickness 91.4(190) mm (With stand) Height 436.6(449) mm Weight 9.22 kg Power requirements 100-240Va.c. 50/60Hz Television system PAL-BG, I, DK / SECAM-BG, DK, / NTSC-M Television programme VHF: 0~12 UHF :21~69 Cable : S1~S4...
Page 30 - Troubleshooting; Check item
Troubleshooting No picture on screen and no soundfrom speakers No picture/No picture from AVterminal Picture is displayed, but no soundfrom the speakers. Picture is too light There are stripes on the screen orcolors fade. Picture is too dark. Remote control does not work. The picture is not sharp.Th...
Page 31 - NEC Service Centres; New South Wales
22 31 NEC Australia Pty. Ltd. ABN 86 001 217 527 DISPLAY AND HOME GROUP NEC Service Centres New South Wales Sydney 184 Milperra Rd, Revesby 2212 131-632 Newcastle 120 Parry Street, Newcastle West 2302 131-632 Victoria Melbourne Unit1/6, Garden Road, Clayton, 3168 131-632 Queensland Brisbane Unit 4/3...
Page 32 - NEC Australia Pty Ltd
