Page 2 - Index
Index Warning 1 Contents 2 Quick Start 3-7 Controls 8-9 Recommended Use 10-11 Specifications 12 Features 13 Troubleshooting 14 References 15 Limited Warranty 16 TCO ’99 17-18 Avertissement 20 Contenu 21 Mise en marche rapide 22-26 Commandes 27-28 Usage recommandé 29-30 Fiche technique 31 Fonctions 3...
Page 3 - WARNING; Canadian Department of Communications Compliance Statement
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE PRONGS CAN BE FULLY INSERTED. REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER S...
Page 4 - Contents; Your new NEC Technologies MultiSync; You can register your product online at
Contents 2 Your new NEC Technologies MultiSync ® LCD monitor box* should contain the following: • MultiSync LCD 1525S ™ monitor with tilt/swivel base • Power Cord (# 70810786)• AC Adapter (#A2425S01) (located in base) • Video Signal Cable• USB Cable• User’s Manual * Remember to save your original bo...
Page 5 - Quick Start; To attach the MultiSync
Quick Start To attach the MultiSync ® LCD monitor to your system, follow these instructions: 1. Turn off the power to your computer.2. For the PC: Connect the 15-pin mini D-SUB of the appropriate signal cable to the connector of the display card in your system (Figure A.1) . Tighten all screws. For ...
Page 8 - CAUTION
6 Quick Start cont. Tilt Grasp both sides of the monitor screen with your hands and adjust the tilt as desired (Figure TS.1). Remove Monitor Stand for Mounting To prepare the monitor for alternate mounting purposes: 1. Remove the back cover and the cable cover (Figure R.1) . Figure R.1 Figure R.2 No...
Page 9 - Remove AC Adapter from Monitor Stand
7 Quick Start cont. Remove AC Adapter from Monitor Stand To remove the AC Adapter 1. Remove the back panel and remove cable cover (Figure AC.1). 2. Disconnect all cables. 3. Place monitor face down on a non-abrasive surface (Figure AC.2). 4. Remove the 4 screws on the bottom of the stand and lift bo...
Page 10 - Brightness and Contrast; Controls
8 INPUT SELECT If no OSM menu is displayed, video input and USB upstream can be changed by pressing the PROCEED button. : Changes only video: Changes video and USB OSM ™ (On-Screen-Manager) Controls To acess OSM press any of control buttons ( , , , ). The OSM controls on the front of the monitor fun...
Page 12 - Safety Precautions and Maintenance; Recommended Use
10 Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE MULTISYNC ® LCD COLOR MONITOR: • DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or othe...
Page 13 - Recommended Use cont.
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for warm-up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level. Your eye...
Page 14 - Specifications
Specifications 12 Monitor MultiSync ® LCD 1525S ™ Notes Specifications Monitor LCD Module Diagonal: 15.4 inch Active matrix; thin film transistor (TFT) Viewable Image Size: 15.4 inch liquid crystal display (LCD); 0.2385 mm dot Native Resolution (Pixel Count): 1280 x 1024 pitch; 200cd/m 2 white lumin...
Page 15 - Features
13 Features NuCycle ™ Plastic: A special silicone compound for PC resin, being extremely flame retardant, safe and environmentally friendly. Dual Inputs: Offers dual inputs, allowing you to connect the monitor to two systems. You can easily switch between computers with a touch of a button on the fr...
Page 16 - Troubleshooting
14 Troubleshooting No picture • The signal cable should be completely connected to the display card/computer. • The display card should be completely seated in its slot. • Power Switch and computer power switch should be in the ON position. • Check to make sure that a supported mode has been selecte...
Page 17 - References
15 References • BBS (978) 742-8706 NEC Technologies’ Remote Bulletin Board System is an electronic service accessible with your system and a modem. Communication parameters are: 300/1200/2400/9600/14.4k/28.8k/33.6k bps, no parity, 8-data bits, 1 stop bit • Customer Service/ Technical Support (800) 6...
Page 18 - Limited Warranty
16 Limited Warranty NEC Technologies, Inc. (hereinafter “NECTECH”), warrants this Product to be free fromdefects in material and workmanship and, subject to the conditions set forth below, agreesto repair or replace (at NECTECH’s sole option) any part of the enclosed unit which provesdefective for a...
Page 20 - CFCs
18 TCO’99 cont. accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur.TCO’99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound chlorine...
Page 22 - AVERTISSEMENT
20 AFIN D’ÉVITER TOUT RISQUE D’INCENDIE OU D’ÉLECTROCUTION, NE PAS EXPOSER CET APPAREIL À LA PLUIE OU À L’HUMIDITÉ. NE PAS UTILISER LA FICHE D’ALIMENTATION POLARISÉE AVEC UNE PRISE DE CORDON DE RALLONGE OU AUTRE PRISE SAUF SI LES BROCHES PEUVENT ÊTRE ENTIÈREMENT INTRODUITES. NE PAS OUVRIR LE BOÎTIER...
Page 23 - La boîte* de votre nouveau moniteur NEC Technologies MultiSync; Contenu; Votre produit peut être enregistré sur Internet à l’adresse
La boîte* de votre nouveau moniteur NEC Technologies MultiSync ® contient : • Moniteur MultiSync LCD 1525S avec socle inclinable/rotatif • Cordon d'alimentation (N ° 70810786) • Adaptateur CA (N ° A2425S01) • Câble d’interface vidéo• Câble d’USB• Manuel de l’utilisateur 21 * Ne pas oublier de conser...
Page 24 - Mise en marche rapide
Pour raccorder le moniteur MultiSync ® LCD au système, suivez les directives ciaprès : 1. Mettez l’ordinateur hors tension. 2. PC : Branchez le mini-connecteur D-SUB à 15 broches du câble vidéo approprié dans le connecteur de la carte vidéo de votre ordinateur (Figure A.1). Serrez toutes les vis. Ma...
Page 27 - Incliner et pivoter
25 Incliner et pivoter Placez les mains de chaque côte du moniteur et réglez l’inclinaison et la position souhaitées (Figure TS.1). Enlever le support du moniteur pour lemontage Pour préparer le moniteur à différents types de montage : 1. Retirez le couvercle arrière et le couvercle du câble (Figure...
Page 28 - Enlever l’adaptateur CA le support du moniteur
26 Enlever l’adaptateur CA le support du moniteur Pour enlever l’adaptateur CA : 1. Retirez le courvercle arrière et le courvercle du câble (Figure AC.1). 2. Déconnectez tous les câbles. 3. Placez le moniteur la face vers le bas sur une surface non abrasive (Figure AC.2). 4. Retirez les 4 vis au bas...
Page 29 - Commandes; Entrée Choisie; Commandes OSM Display Screen (Gestionnaire à l’écron); Commandes de luminosité/contraste; Réglage automatique
27 Commandes Entrée Choisie Si aucun menu d’OSM MC n’est affiché, l’entrée et l’USB visuels en amont peuvent être changés en appuyant sur le bouton de PROCEED. Changements visuels vidéoUSB de changements soulement Commandes OSM Display Screen (Gestionnaire à l’écron) Pour accéder au menu OSM, appuye...
Page 30 - Réglage image; Système de contrôle des couleurs AccuColor; Information
Réglage image H.Size : Régle la dimension horizontale de l’image en augmentant ou en diminuant le format horizontal. FIN : Améliore la mise au point, la netteté et la stabilité de l’image en augmentant ou en di,imuant la valeur Fin. Réglage automatique : Ajuste automatiquement le réglage du format H...
Page 31 - Usage recommandé; Consignes de sécurité et d’entretien
Usage recommandé 29 Consignes de sécurité et d’entretien POUR UN FONCTIONNEMENT OPTIMAL, PRIÈRE DE NOTER CE QUI SUIT POUR LE RÉGLAGE ET L'UTILISATION DU MONITEUR COULEUR MULTISYNC ® LCD : • NE PAS OUVRIR LE MONITEUR. Aucune pièce intérieure ne nécessite l'intervention de l'utilisateur, et l'ouvertur...
Page 33 - Fiche technique
31 Fiche technique Caractér. techniques Moniteur Remarques du moniteur MultiSync ® LCD 1525S MC Module LCD Diagonale : 15,4 pouces Matrice active; transistor à film fin (TFT); Surface utile : 15,4 pouces affichage àcristaux liquides (LCD); pas Résolution (nombre de pixels) : 1 280 x 1 024 0,2385 mm;...
Page 34 - Fonctions
32 Fonctions NuCycle MC Plastique : Un composé spécial de la silicone pour la résine PC, qui est extrémement résístant à flamme, aussi bien que sécuritaire et pour l’environnement. Entrées Duelles : Le moniteur offre les entrées duelles, vous permettant de relier le moniteur à deux systèmes. Vous po...
Page 35 - Dépannage
33 Dépannage Pas d'image • Le câble vidéo doit être bien connecté à la carte d'affichage et à l’ordinateur. • La carte d'affichage doit être insérée à fond dans son logement. • Les interrupteurs d’alimentation du moniteur et de l’ordinateur doivent être sur la position MARCHE. • Vérifiez qu’un mode ...
Page 37 - Garantie limitée
35 Garantie limitée NEC Technologies, Inc. (ci-après «NECTECH») garantit que ce produit est exempt de vice defabrication et de main-d’oeuvre et, selon les conditions énoncées ci-dessous, accepte de réparerou remplacer, à sa discrétion, toute pièce de l'appareil concerné qui s'avérerait défectueuse e...
Page 38 - Pourquoi des ordinateurs «éco-étiquetés»?; Exigences environnementales
36 TCO’99 Félicitations! Vous avez acheté un produit qui répond à la directive TCO’99. En choisissant ce produit conçu pour une utilisation professionnelle, vous contribuez aussi à la réduction des effets nuisibles sur l’environnement et aussi au développement continu de produits électroniques respe...
Page 41 - DÉCLARATION DE CONFORMITÉ; Série LCD NEC
AVIS DE PROPRIÉTÉ EXCLUSIVE ET DE DÉGAGEMENT DE RESPONSABILITÉ Les informations contenues dans ce document, y compris tous les designs et matériel s'y rapportant, sont la propriété de NEC Technologies et/ou ses concédants. NEC Technologies se réserve les droits de fabrication brevetée, les droits d’...
Page 42 - NEC LCD Series; DECLARATION OF CONFORMITY
Part No. 78134761 Printed in Japan NEC LCD Series PROPRIETARY NOTICE AND LIABILITY DISCLAIMER The information disclosed in this document, including all designs and related materials, is the valuable property of NEC Technologies and/or its licensors, as appropriate, reserve all patent, copyright and ...