NEC 5800/320Fd - Manual - manualsarea.com

Page 2 - Notice

Notice The information contained in this document is subject to change without notice. UNLESS EXPRESSLY SET FORTH IN A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED REPRESENTATIVE OF NEC, NEC MAKES NO WARRANTY OR REPRESENTATION OF ANY KIND WITH RESPECT TO THE INFORMATION CONTAINED HEREIN, INCLUDING WARR...

Page 3 - Contents

-iii- Contents Introduction 1 Packaged Cabinet 1 Before Unpacking the Cabinet 3 Moving the Cabinet to the Installation Site 6 Unpacking and Checking the Cabinet 7 Tools Needed to Unpack the Cabinet 8 Removing the Packing Materials 8 Removing the Cabinet from the Pallet 15 Checking the Cabinet and Sy...

Page 5 - Introduction; Cabinets; W A R N I N G; N O T E; Packaged Cabinet; Figure 1

-1- Introduction Read Me First: Unpacking Express5800/320 F d Cabinets describes how to move cabinets that contain these systems to an installation site and how to unpack them. Warnings, cautions, and notes in this document convey the following special information: W A R N I N G ! A warning indicate...

Page 7 - Before Unpacking the Cabinet; C A U T I O N; Contact the vendor from

-3- Before Unpacking the Cabinet 1. Check the packing list to verify that you have received the correct shipment. 2. Verify that the Tip-N-Tell and Shockwatch handling indicators on the outside of the shipping container have not been activated. C A U T I O N ! If you received the wrong shipment or a...

Page 8 - Figure 2. Dimensions of a Packaged 38U Cabinet

-4- Figure 2. Dimensions of a Packaged 38U Cabinet 80 in. (2m) 41 in. (104.14 cm) 53 in. (134.62 cm) 5 in. (12.7 cm) 38U Cabinet hsys033

Page 10 - Moving the Cabinet to the Installation Site

-6- If the corridor and door dimensions are large enough to accommodate the unpacked cabinet still tied to its pallet, use a pallet jack to move it from the delivery site to the installation site, as described in “Moving the Cabinet to the Installation Site” on page 6 . If the corridor and door dime...

Page 11 - “Stabilizing the Systems”; Figure 4; Unpacking and Checking the Cabinet; To unpack the cabinet

-7- present, see the section “Stabilizing the Systems” on page 19 for stabilization guidelines. When shipped, the system cabinet is tied to the pallet beneath it. The pallet has a clearance for a pallet jack to move the unit. When moving a system cabinet, follow these guidelines: 1. Verify that the ...

Page 12 - Tools Needed to Unpack the Cabinet; Use the following tools to unpack the cabinet:; Removing the Packing Materials

-8- Tools Needed to Unpack the Cabinet Use the following tools to unpack the cabinet: • Metal shears to cut pallet straps • Pair of scissors or utility knife • One 3/8-inch drive ratchet with a 9/16-inch socket Removing the Packing Materials W A R N I N G ! To avoid personal injury or damage to the ...

Page 14 - “Stabilizing the Systems” on page 19

-10- Figure 6. Removing the Packing Material 6. Remove the plastic wrap encasing the cabinet. C A U T I O N ! If condensation exists inside the plastic wrap, you must provide a stabilization period for the systems. “Stabilizing the Systems” on page 19 hsys036

Page 19 - Removing the Cabinet from the Pallet

-15- Figure 11. Sliding Back the Wooden Restraint Blocks 14. Move the lever bar to the opposite side of the cabinet. Repeat the process of tilting the cabinet and sliding back the two wooden restraint blocks on the opposite side of the cabinet. Removing the Cabinet from the Pallet 1. Position the pa...

Page 21 - Figure 13. Moving the Cabinet Down the Pallet Ramp; Checking the Cabinet and Systems; Corporation of America

-17- Figure 13. Moving the Cabinet Down the Pallet Ramp 3. Check the cabinet and systems for damage, as the next section describes. Checking the Cabinet and Systems Check the cabinet, systems, and optional components for damage: 1. Open the rear door of the cabinet. From the bottom of the cabinet, r...

Page 22 - Serial Number

-18- Verifying the Express5800/320 F d Serial Number Find the equipment label to check the Express5800/320 F d serial number. To find the equipment label, open the rear door of the cabinet. The equipment label is attached to the rear of each system.Check that the Express5800/320 F d serial number (n...

Page 23 - Stabilizing the Systems; Table 1

-19- Stabilizing the Systems If temperature and humidity changes have been extreme during transit, the cabinet and systems might develop condensation. Therefore, before you install and power on the systems, you must inspect them and the cabinet for condensation and, if necessary, stabilize the syste...

Page 24 - : Site Planning Guide; Disposing of Shipping Materials; To install a system, see the; System Documentation; The; Fd; are found on the

-20- 4. Continue the installation, and continue to inspect for signs of condensation. If condensation appears, allow additional stabilization periods until there are no signs of condensation. C A U T I O N ! Before you power on the systems, verify that the installation site environment meets the req...

Page 25 - Getting Help; Online support from NEC Technical Support.; NEC Technical Support Web site; Online product support for Microsoft; Microsoft Help and

-21- To gain access to the documents on the World Wide Web, point your browser to: http://support.necam.com/servers/ Getting Help If you have a technical question about Express5800/320 F d hardware or software, try these online resources first: • Online support from NEC Technical Support. You can fi...

NEC 5800/320Fd - Manual

Table of Contents:

Summary

Other NEC Models