NEC 1800 - Manual
NEC 1800 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Installing the 500-sheet 2nd Cassette; NEC
- Page 3 – DA
- Page 4 – Accessing the Printer Controller Board; Introduction; Cut Here
- Page 5 – Installing the LocalTalk and Serial Interface Card
A Phillips-head screwdriver is required for installing the NEC SuperScript 1800 PostScript
®
Level 2 Upgrade Kit.
Accessing the Printer Controller Board
Installing the PostScript Level 2 SIMM
This upgrade kit comes with one PostScript
®
Level 2 compatibility SIMM.
This product is not manufactured or distributed by Adobe Systems, Inc., the owners of the registered trademark PostScript
®
.
1. Turn off the printer.
2.
Pull-out 500-sheet Cassette
(A)
.
3. Disconnect all cables from printer.
4. Position the printer so right-side can be accessed.
5. Remove screws from side-panel then open back-
panel
(B)
.
6. Pull tab to release side-panel
(C)
.
7. Slide side-panel towards back
(D)
.
8. Rotate side-panel away from printer (assure wire-snaps
on the parallel port are not in way), then lift away
(E)
.
9. Loosen top screw of controller board cover, remove
remaining 4 screws, then remove cover
(F)
.
1. Position the printer so you have access to the
controller board.
2.
Figure
(A)
shows the controller board and the
location of the PostScript SIMM slot. The PostScript
SIMM must be installed into the first slot.
3. Locate notch on the SIMM
(B)
.
4. Position the SIMM into the slot so that the notch is at
the bottom
(C)
.
5. Snap the SIMM into position
(D)
.
6. Use previous procedure as guide to replace printer side-
panel, 500-sheet Cassette, and printer cables.
7. For computers running Microsoft Windows, install a
PostScript printer driver as described by Chapter 3,
“Installing the Software,” of the SuperScript 1800 User ’s
Guide. For Macintosh computers, use the Mac OS Help
system for choosing a PostScript printer.
A
B
C
D
E
F
B
A
D
C
Install the PostScript SIMM into the first slot.
Notch
NEC
P
ART
N
O
. 808-878303-011A
S
UPER
S
CRIPT
1800
P
OST
S
CRIPT
®
L
EVEL
2 C
OMPATIBILITY
U
PGRADE
K
IT
I
NSTRUCTIONS
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Use this instruction sheet for installing the optional NEC SuperScript 1800 500-sheet 2nd Cassette (Tray 3). The cassette can hold 500 sheets of medium weight paper or 40 envelopes. Do not load transparencies or label sheets in the 500-sheet 2nd Cassette. For a complete list of usable media sizes se...
A Phillips-head screwdriver is required for installing the NEC SuperScript 1800 IrDA and Serial Interface Upgrade Kit. Accessing the Printer Controller Board Installing the IrDA Interface Card and Adapter 1. Turn off the printer. 2. Pull-out 500-sheet Cassette (A) . 3. Disconnect all cables from pri...
Tools Required Accessing the Printer Controller Board Turn off the printer.Pull-out the Tray 2 (A).Disconnect all cables from printer.Position the printer so the right-side can be accessed.Remove screws from side-panel, then open back panel (B). 1.2.3.4.5. Rotate side-panel away from the printer (as...
