Navman LA000507 - Manual
Navman LA000507 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Technical configuration
- Page 4 – Equipment supplied; This kit should contain the items illustrated in Figure 2-1.; Jupiter 20 GPS Development Unit; usage under various conditions; Serial interface cable
- Page 5 – and evaluation for both NMEA and SiRF Binary formats.; Equipment required
- Page 6 – functionality of the Jupiter 20 GPS Development Unit.; Figure 3-1 Front and back panels of the Jupiter 20 development unit; and satellite ephemerides.; with these serial ports.
- Page 7 – Configuration DIP switch; ON; Configuration DIP switch.; Switch; Serial BOOT; Table 3-1 DIP switch settings
- Page 8 – DIP switch 5 – RTC backup power enable; even with the main power switch in the OFFposition.; DIP switch 8 – Antenna preamp power enable; the active antenna supplied with the kit.; Figure 3-3 Function LEDs on front panel; This LED indicates presence of primary DC power to the module.
- Page 9 – Clock out connector; Pin number; not used; Table 3-2 Pin functions of the clock out connector; Manufacturer; Molex; Table 3-3 Mating connector part description; Internal configuration; illustrates the internal layout of the Development Unit board.; Figure 3-5 Internal layout of the Development Unit
- Page 10 – Table 3-4 Pin functionality; signals available on the test points are shown in Table 3-5.; Test point; Table 3-5 Signals available on the test points; in conjunction with the Development Unit. These are as follows:
- Page 11 – Jupiter 20 module on adapter board; Figure 3-6 Jupiter 20 adapter board; Table 3-6 lists the pin configurations for the J1 and J2 connectors.; Jupiter function; GND
- Page 12 – Operating instructions; Initial connection and operation; Development Unit’s Serial Port 1.; Positioning the GPS antenna
- Page 13 – Figure 4-1 Development Unit test equipment; Operating the GPS Analyser software; must be enabled in the NMEA protocol for this software to be used.; To enable the receiver output; the Baud rate to 9600 Baud.
- Page 14 – the following characteristics:; To set the receiver output to SiRF binary; from the drop down menu.; DR connector pin configuration
- Page 15 – factor; Table 5-1 Gyro input specifications; Acronyms used in this document; National Marine Electronics Association
LA000510C © 2006 Navman NZ Ltd. All rights reserved. Proprietary information and specifications subject to change without notice.
Related products
• Jupiter 20 (standard)
TU20-D411-001
• Jupiter 20 S (high sensitivity)
TU20-D411-101
• Jupiter 20 D (dead reckoning)
TU20-D421-201
Related documents
• Jupiter 20 Product brief LA000509
• Jupiter 20 Data sheet LA000507
• Jupiter 20 DR Application note LA000433
• Jupiter 30 / 20 Integrator’s manual LA000577
• SiRF Binary Protocol reference manual
MN000314
• NMEA reference manual MN000315
• SiRFDemo and SiRFflash user guides
Jupiter 20
GPS receiver module
Development kit guide
Applies only to older models:
TU10-D007-400
TU10-D007-401
TU10-D007-402
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
LA000510C © 2006 Navman NZ Ltd. All rights reserved. Proprietary information and specifications subject to change without notice . Contents1.0 Introduction ....................................................................................................... 42.0 Equipment.............................
(1) (2) (3) (4) (5) (6) software and documentation Serial Port 1 Antenna DR Clock Out Serial Port 2 - + DC Power 9-16Volts 4 LA000510C © 2006 Navman NZ Ltd. All rights reserved. Proprietary information and specifications subject to change without notice. 1.0 Introduction The TU10-D007-400 series of ...
5 LA000510C © 2006 Navman NZ Ltd. All rights reserved. Proprietary information and specifications subject to change without notice. 5. Power adapter for 12 VDC vehicle operation For mobile operation, an automotive adapter intended for use in 12 VDC vehicles is provided. 6. Software and documentation...
