Navman LA000578A - Manual
Navman LA000578A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 4 – platform for evaluation purposes.; Equipment supplied; This kit should contain the items illustrated in Figure 2-1.; Jupiter 30 GPS development unit; usage under various conditions
- Page 6 – Software and documentation CD; SiRFflash), and other information on how to use GPS receivers.; Equipment required; Technical configuration; functionality of the Jupiter 30 GPS development unit.
- Page 7 – Configuration DIP switch; ON; Configuration DIP switch.; Switch; Serial BOOT; Table 3-1 DIP switch settings
- Page 8 – even with the main power switch in the off position.; Dip; the preamp function.; DIP switch 8 – Antenna preamp power enable; the active antenna supplied with the kit.; Figure 3-5 Internal layout of the development unit
- Page 9 – Figure 3-3 Function LEDs on front panel; This LED indicates presence of primary DC power to the module.; Clock out connector; Pin number; not used; Table 3-2 Pin functions of the clock out connector
- Page 10 – Figure 3-6 Jupiter 30 adapter board
- Page 11 – Figure 3-4 Pin layout of the clock out connector; Manufacturer; Molex; Table 3-3 Mating connector part description; Internal configuration; Pins; the Jupiter 30 module.; Table 3-4 Pin functionality
- Page 12 – signals available on the test points are shown in Table 3-5.; Test point; TXA; Table 3-5 Signals available on the test points; in conjunction with the development unit. These are as follows:
- Page 13 – Jupiter 30 module on adapter board; Table 3-6 lists the pin configurations for the J1 and J2 connectors.; Jupiter function; VDD; Operating instructions; Initial connection and operation; Install the supplied SiRFdemo on your PC:
- Page 14 – development unit’s Serial Port 1.; Positioning the GPS antenna
- Page 15 – Operating the GPS Analyser software; must be enabled in the NMEA protocol for this software to be used.; To enable the receiver output; the Baud rate to 9600 Baud.; Figure 4-1 Development unit test equipment
- Page 16 – To set the receiver output to SiRF binary; from the drop down menu.; Acronyms used in this document; One Pulse Per Second
LA000578A © 2006 Navman New Zealand. All rights reserved.
Proprietary information and specifications subject to change without notice.
Jupiter 30
20-channel GPS receiver
module
Development kit Guide
(AA003029 series)
Related products
Jupiter 30 (standard) AA003025-G
Related documents
• Jupiter 30 Data sheet LA000576
• Jupiter 30 Product brief LA000575
• SiRF Binary Protocol reference manual
MN000314
• NMEA reference manual MN000315
• SiRFDemo and SiRFflash
user guide
MN000316
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
4 LA000578A © 2006 Navman New Zealand. All rights reserved. Proprietary information and specifications subject to change without notice. 1.0 Introduction This document provides detailed guidelines for the operation and configuration of the Jupiter 30 GPS Module Development Kit. The AA003029 series o...
6 LA000578A © 2006 Navman New Zealand. All rights reserved. Proprietary information and specifications subject to change without notice. 6. Software and documentation CD The CD contains the Jupiter 30 GPS receiver data sheet, PC Analysis software (SiRFDemo and SiRFflash), and other information on ho...
7 LA000578A © 2006 Navman New Zealand. All rights reserved. Proprietary information and specifications subject to change without notice. 3.1.7 Serial port 2 This is the auxiliary serial port, and primarily used for the reception of RTCM SC-104 DGPS (Differential GPS) correction messages. 3.1.9 Anten...
