NAD C3050BLUOS - User Manual

Page 2 - ENGLISH; IMPORTANT SAFETY INSTRUCTIONS

ENGLISH 2 • Read instructions - All the safety and operating instructions should be read before the product is operated. • Retain instructions - The safety and operating instructions should be retained for future reference. • Heed Warnings - All warnings on the product and in the operating instructi...

Page 4 - INTRODUCTION; TABLE OF CONTENTS

ENGLISH INTRODUCTION TABLE OF CONTENTS 4 IMPORTANT SAFETY INSTRUCTIONS INTRODUCTION WHAT’S IN THE BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5FACTORY RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 5 - WHAT’S IN THE BOX; SAVE THE PACKAGING; FACTORY RESET; IMPORTANT; GETTING STARTED

ENGLISH WHAT’S IN THE BOX Packed with your C 3050 you will find: • Two detachable mains power cord • SR 10 remote control with 2 AA batteries • Bluetooth antenna • Quick Setup Guide SAVE THE PACKAGING Please save the box and the packaging that came with your C 3050. Should you move or need to transp...

Page 6 - NAD VU METER; Conditions for Power button to activate; AUTO STANDBY; ENABLE/DISABLE AUTO STANDBY MODE; – PHONO Source LED indicator flashes twice.; Disabled; - PHONO Source LED indicator flashes once.; IDENTIFICATION OF CONTROLS; FRONT PANEL

ENGLISH 6 1 NAD VU METER • The C 3050 is equipped with a pair of Power meters that monitors the Input Signal or Speaker Output levels. • Both Power meters are calibrated in Watts and dB (decibel) that corresponds to an 8-ohm load. • Refer also to item about VU METER in the IDENTIFICATION OF CONTROLS...

Page 7 - DEEP STANDBY MODE; DESCRIPTION; BLUETOOTH AS A SOURCE

ENGLISH 7 IDENTIFICATION OF CONTROLS FRONT PANEL DEEP STANDBY MODE At Deep Standby mode, the C 3050 switches to standby mode at lowest power consumption (less than 0.5W ). SET C 3050 TO DEEP STANDBY MODEa At operating mode, press and hold the front panel POWER button until the Power LED indicator fl...

Page 8 - REAR PANEL; • Ensure that the audio setting/format of eARC-connected devices to; CEC POWER; Enabled; Ensure that the C 3050 is plugged-in to a grounded AC wall outlet.

ENGLISH 8 ATTENTION! Please make sure that the C 3050 is powered off or unplugged from the mains power source before making any connections. It is also advisable to power down or unplug all associated components while making or breaking any signal or AC power connections. IDENTIFICATION OF CONTROLS ...

Page 9 - 0 AC MAINS INPUT; MDC2 UPGRADE SLOTS

ENGLISH 9 • The PRE OUT output signal will be affected by the C 3050’s volume and tone control settings. • Always turn OFF the C 3050 and associated external power amplifiers before connecting or disconnecting anything to the PRE OUT sockets. 8 SUBW • Connect SUBW to the low level input of correspon...

Page 10 - IMPORTANT NOTES; or functional for the particular device.; AMP; SR 10 REMOTE CONTROL

ENGLISH 10 The SR 10 remote control handset handles the key functions of the C 3050. It can also control up to 4 devices. The SR 10 can operate up to a distance of 23 ft (7m). Alkaline batteries are recommended for maximum operating life. Two AA batteries must be fitted in the battery compartment at...

Page 11 - CD; Ensure that your applicable NAD product is set to BluOS source.

ENGLISH 11 IDENTIFICATION OF CONTROLS SR 10 REMOTE CONTROL CD PLAYER CONTROL (applicable to NAD CD Players): Select CD among the DEVICE SELECTOR buttons to gain access to the following applicable control buttons. Check the owner’s manual of your applicable NAD CD Player for control button compatibil...

Page 12 - AUX; USING THE SR 10 REMOTE CONTROL LIBRARY; TABLE OF LIBRARY CODES APPLICABLE TO SR 10 REMOTE CONTROL; Default library for “AMP” page; RESET SR 10 TO ITS FACTORY DEFAULT SETTINGS

ENGLISH IDENTIFICATION OF CONTROLS SR 10 REMOTE CONTROL AUX PLAYER CONTROL (applicable to NAD Tuners): Select AUX among the DEVICE SELECTOR buttons to gain access to the following applicable control buttons. The AUX device is defaulted to NAD Tuner device remote control codes. SOURCE [ D/F ]: Step u...

Page 13 - PREAMPLIFIER SECTION; REFERENCE; SPECIFICATIONS

ENGLISH 13 All specs are measured according to IHF 202 CEA 490-AR-2008 standard. THD is measured using AP AUX 0025 passive filter and AES 17 active filter. PREAMPLIFIER SECTION LINE INPUT, PRE-OUT THD (20 Hz – 20 kHz) <0.005 % at 2V out Signal-to-Noise Ratio >95 dB (IHF; A-weighted, ref. 500 m...

Page 14 - GENERAL SPECIFICATIONS

ENGLISH 14 GENERAL SPECIFICATIONS MAIN IN, SPEAKER OUT Continuous output power into 8 ohms and 4 ohms 100W (ref. 20 Hz-20 kHz at rated THD, both channels driven) THD (20 Hz – 20 kHz) <0.03% (250 mW to 100 W, 8 ohms and 4 ohms) Signal-to-Noise Ratio >95dB (A-weighted, 500 mV input, ref. 1 W out...

NAD C3050BLUOS - User Manual

Table of Contents:

Summary

Other NAD Amplifiers Models