Msd 8235 Inductive Blaster SC Coil Installation- User Manual
Msd 8235 Inductive Blaster SC Coil Installation– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Figure 2 Assemble the Coil and Driver.; ASSEMBLE THE COIL AND DRIVER; Primary Wires: The two primary wires, Red and
- Page 3 – Figure 4 Wiring the Coil and Driver with an MSD CD Ignition Control.; TECH NOTES; WIRING AN MSD IGNITION CONTROL
- Page 4 – Limited Warranty; or consequential damages.; Service; When returning MSD components for warranty service,; Proof of Purchase must be supplied for verification. After; All returns must have a Return Material Authorization (RMA) number; issued to them before; M S D
MSD Blaster SC Coil
PN 8235
IMPORTANT: Read the instructions before attempting the installation.
Parts Included:
1 - Blaster SC Coil, PN 8235
1 - Parts Bag and Mounting Hardware
1 - MSD 90° Boot and Terminal
WARNING: During installation, disconnect the battery cables. When disconnecting the battery,
always remove the Negative cable first and install it last.
WARNING: The Blaster SC Coil and Coil Driver produce very high voltage and current. Use
caution during installation and while working near the Coil assembly.
The MSD Blaster SC Coil is designed to be used with the SC Coil Driver, PN 6305, and Pro-Billet
Honda Distributor, PN 8488. An MSD SCI, 6-Series and 7-Series Ignition Control may also be used.
The Blaster SC Coil cannot be used with factory ignition systems as a stand alone coil.
COIL LOCATION AND MOUNTING
1. Find a suitable mounting location for the Coil
and Driver assembly. It can be mounted in any
position as long as it is away from direct engine
heat sources. Also make sure that the Coil Driver
wiring harness reaches the distributor.
2. Ensure that there is enough room to clear the Coil
and the Coil Driver when they are assembled.
3. Use the Coil as a template and mark the mounting
holes. Figure 1 also provides a template to assist
in the mounting.
4. Use a 3/16" drill bit to make the mounting
holes.
Figure 1 Coil Mounting Template.
Components Required:
1 - SC Coil Driver, PN 6305
1 - Pro-Billet Honda Distributor, PN 8488
M S D
• W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 INSTALLATION INSTRUCTIONS M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Figure 2 Assemble the Coil and Driver. Figure 3 Wiring the Coil and Driver to the Distributor. ASSEMBLE THE COIL AND DRIVER 1. Position the ...
INSTALLATION INSTRUCTIONS 3 M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 Figure 4 Wiring the Coil and Driver with an MSD CD Ignition Control. TECH NOTES ____________________________________________________________...
Limited Warranty M SD warrants this product to be free from defects in material and workmanship under its intended normal use*, when properly installed and purchased from an authorized MSD dealer, for a period of one year from the date of the original purchase. This warranty is void for any products...
