Msd 6214 Midget DIS-2 Programmable Race Ignition Insta- User Manual
Msd 6214 Midget DIS-2 Programmable Race Ignition Insta– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – operate momentarily with a supply voltage as low as 9 Volts.; Note: The negative battery terminal must be grounded; 2 volt square wave signal with a 30° duty cycle.; Solid Core spark plug wires cannot be used.; PROGRAMMING OPTIONS
- Page 3 – HAND HELD PROGRAMMER, PN 7550; PROGRAMMING FEATURES; RUN TIMING RETARD CURVE; Figure 1
- Page 4 – Note: There is an offset of 4° from the input signals
- Page 5 – TRIGGER WHEEL FABRICATION; MOUNTING THE TRIGGER PICKUPS; Figure 2 Mounting the Magnet in the Trigger Wheel.
- Page 6 – WIRING AND INSTALLATION; MOUNTING; Figure 4 Installing the
- Page 7 – specified to go to ground, it should be connected to the; battery negative terminal, engine; SETTING STATIC TIMING; pickup should be connected to the Violet and Green wiring harness.; Figure 5 Wiring the MSD Programmable Midget Ignition System.
- Page 8 – INSTALLATION; SAVES AND TRANSFERS
- Page 9 – MONITOR; DEFAULT SETTINGS; REV LIMITER OPTIONS; Display; Figure 6 RPM and Retard Monitor.
- Page 10 – ALTERNATE TIMING CURVE
- Page 11 – ALERTS; The Alerts will provide a flash code to the LED on the outside of; Data Editor Window; MENU TREE; Menus; PN 6214 Flow Chat with Hand Held Monitor; as displayed on the 7550 Terminal
- Page 12 – TROUBLESHOOTING; LED; idle speeds when everything is functioning properly.; MISSES AND INTERMITTENT PROBLEMS; grounded to the engine block.
- Page 13 – CHECKING FOR SPARK; Figure 7 False Triggering Channel
- Page 14 – Tech Notes
- Page 16 – Limited Warranty; Service; Proof of Purchase must be supplied for verification. After; issued to them before; M S D; Revised; TECH NOTES
GENERAL INFORMATION
DIGITAL OPERATION
The Programmable Midget Ignition uses a high speed RISC microcontroller to control the
ignition’s output while constantly analyzing the various inputs such as supply voltage, trigger
signals and rpm. The high speed controller can make extremely quick compensations to the
timing and rpm limits while maintaining accurate timing signals to within +/- 0.1° and +/- 10
rpm. The circuits and controller of the Ignition have been thoroughly debounced and sup-
pressed to create protection against Electro Magnetic Interference (EMI).
Note: This Ignition can be removed from power and still retain its programmed settings.
CAPACITIVE DISCHARGE
The Midget Ignition features a capacitive discharge ignition design. The majority of stock
and aftermarket ignition systems are inductive ignitions. In an inductive ignition, the coil must
store energy and step up the supplied voltage to maximum strength between each firing. At
higher rpm, since there is less time to charge the coil to full capacity, the secondary voltage falls
short of reaching its maximum energy level which results in a loss of power or a top end miss.
The Midget Ignition features a capacitor which is quickly charged to 490 - 505 volts and
stores this energy until the ignition is triggered. With the CD design, the voltage sent to the
coil is always at maximum power even at high rpm.
Programmable Midget Racing Ignition Control
PN 6214
1 - Midget Ignition
1 - Magnet .250" x .200"
1 - Aluminum Magnet Rivet
1 - Pro-Data+ Disk
1 - Wire Harness
2 - Ring Terminal (#6 Red)
2 - Ring Terminal (#1/4 Yellow)
1 - ON/OFF Toggle Switch
2 - PN 8159 Pickup
2 - 9-Pin Harness (6', 10')
4 - Vibration Mounts
WARNING: During installation, disconnect the battery cables. When disconnecting the battery
always remove the Negative cable first and install it last.
Note: Solid Core spark plug wires cannot be used with the Midget Ignition.
The MSD Programmable Midget Ignition is a distributorless ignition system (DIS). It provides
powerful capacitive discharge sparks for complete combustion while providing a variety of
rpm and timing tuning programs. It consists of an Ignition Control, 2-Channel Coil Pack, and
incorporates a waste spark firing design. This means that two cylinders are fired at the same
time, one on the compression stroke and the other on the exhaust stroke. Two magnetic
pickups are used for trigger inputs and two outputs go to the supplied coil pack. The com-
ponents offer a direct plug-in wiring harness with sealed, locking Deutsch Connectors. A 12
volt battery is required.
The MSD Programmable Midget Ignition Control requires a crank trigger system. MSD sup-
plies two Non-Magnetic Pickups, but due to the variety of engines and applications, a crank
trigger wheel is not offered. Information is supplied on fabricating a crank trigger wheel.
Note: The Midget Ignition must be used on engines equipped with a battery.
M S D
• W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 INSTALLATION INSTRUCTIONS M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 MULTIPLE SPARKS The Midget Ignition produces full power multiple sparks for each firing of a plug. The number of multiple sparks that occur de...
INSTALLATION INSTRUCTIONS 3 M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 HAND HELD PROGRAMMER, PN 7550 The Hand Held Programmer (Fig. 1) allows you to select and program the different features of the Programmable Mi...
4 INSTALLATION INSTRUCTIONS M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4 REV LIMITER An overrev rpm limit can be programmed in 100 rpm increments from 2,000 to 15,000 rpm. The limiter has a default setting of 9,500 ...
