Mitsubishi HC6000- User Manual
Mitsubishi HC6000– User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – How to set the value
- Page 3 – ) Password lock commands; gures 1 to 4 added to the end of the data code. When; ) Reading command diagram
- Page 4 – ) Menu setting commands
- Page 5 – Use the ASCII or HEX code as shown below to set the value.
1
LCD Projector
HC6000
Controlling the projector using a personal computer
This projector can be controlled by connecting a personal computer with RS-232C terminal.
PC-controllable functions:
• Turning the power ON or OFF
• Changing input signals
• Inputting commands by pressing the buttons on the control panel and remote control
• Menu setting
Connection
HDMI IN-2
HDMI IN-1
SERIAL
TRIGGER
COMPUTER IN/
COMPONENT
VIDEO IN
VIDEO IN
S-VIDEO
IN
PR/
CR
PB/
CB
COMPONENT
VIDEO IN
AC IN
RS-232C cable
SERIAL
D-SUB 9-pin
D-SUB 9-pin
To RS-232C
terminal
Important:
• Make sure that your computer and projector are turned off before connection.
• Boot up the computer
fi
rst, and then plug the power cord of the projector.
(If you do not follow this instruction, the Com port may not function.)
• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.
1) Interface
PROTOCOL
RS-232C
BAUD RATE
9600 [bps]
DATA LENGTH
8 [bits]
PARITY BIT
NONE
STOP BIT
1 [bit]
FLOW CONTROL
NONE
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable, the reverse type cable should be used.
2) Control command diagram
The command consists of the address code, function code, data code, and end code. The length of the command
varies among the functions.
Address code
Function code
Data code
End code
HEX
30h 30h
Function
Data
0Dh
ASCII
‘0’ ‘0’
Function
Data
[Address code]
30h 30h (In ASCII code, ‘0’ ‘0’)
fi
xed.
[Function code]
A code of each
fi
xed control move.
[Data code]
A code of each
fi
xed control data (number) and not always indicated.
[End code]
0Dh (In ASCII code, ‘ ’)
fi
xed.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 3) Control sequence (1) Send the command from the personal computer to the projector.(2) The projector will send a return command after it receives an end code. If the command is not received correctly, the projector will not send the return command. (3) The personal computer checks the command an...
3 6) Remote commands (Not executable in stand-by mode. When the remote commands are sent while the splash screen is being displayed, the splash screen is only canceled.) Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes. Button’s name ...
4 ASCII HEX Function Data (Receive) Function Data (Receive) INPUT S-VIDEO vI v2 76h 49h 76h 32h POWER ON/OFF INPOSSIBLE vPK 0 76h 50h 4Bh 30h POWER ON/OFF POSSIBLE vPK 1 76h 50h 4Bh 31h NO SIGNAL SUPPLIED vSM 0 76h 53h 4Dh 30h SIGNAL SUPPLIED vSM 1 76h 53h 4Dh 31h LAMP OPERATING TIME(on the LOW mode...
