Miller Remote Operator Interface - Manual

Page 2 - To locate your nearest; Thank you; From Miller to You

Miller Electric manufactures a full lineof welders and welding related equipment.For information on other quality Millerproducts, contact your local Miller distributor to receive the latest fullline catalog or individual specification sheets. To locate your nearest distributor or service agency call...

Page 3 - TABLE OF CONTENTS

TABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 5 - ELECTRIC SHOCK can kill.; FUMES AND GASES can be hazardous.

OM-217 834 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _3/05 Y Warning: Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adj...

Page 6 - WELDING can cause fire or explosion.

OM-217 834 Page 2 Arc rays from the welding process produce intense visible and invisible (ultraviolet and infrared) rays that can burn eyes and skin. Sparks fly off from the weld. ARC RAYS can burn eyes and skin. D Wear an approved welding helmet fitted with a proper shade of fil- ter lenses to pro...

Page 7 - ARC WELDING can cause interference.

OM-217 834 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over, or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly s...

Page 9 - Symboles utilisés; Dangers relatifs au soudage à l’arc; UNE DÉCHARGE ÉLECTRIQUE peut

OM-217 834 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION fre_som _3/05 Y Avertissement : se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes. 2-1. Symboles utilisés Symbole graphique d’avertissement ! Attention ! Cette pro- cédure com...

Page 11 - LE RAYONNEMENT HAUTE; Proposition californienne 65 Avertissements

OM-217 834 Page 7 2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance Risque D’INCENDIE OU D’EXPLO- SION. D Ne pas placer l’appareil sur, au-dessus ou à proximité de surfaces inflammables. D Ne pas installer l’appareil à proximité de produits inflammable...

Page 12 - Principales normes de sécurité; Information EMF

OM-217 834 Page 8 2-5. Principales normes de sécurité Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site In- ternet : www.global.ihs.com). Recommended Safe Practices for the Preparation for Welding and Cut- ting of...

Page 13 - SECTION 4

OM-217 834 Page 9 SECTION 3 − INTRODUCTION 3-1. Specifications Type of Input Power Welding Power Source Type Wire Feed Speed Range Wire Diameter Range Welding Circuit Rating Overall Dimensions Weight 40 Volts DC 10 Amperes Axcess Series Standard: 40 To 1400 ipm (1.0 To 35.6 mpm) .035 To 1/16 in (0.8...

Page 15 - -3. Remote Operator Interface And Wire Drive Installation

OM-217 834 Page 11 Ref. 803 697-E Typical Swingarc installation shown; however, various installations are possible depending on the application.1 Remote Operator Interface 2 Swingarc Swivel Assembly 3 Boom 4 AA40G Wire Drive Assembly 5 Trigger Cable 4-3. Remote Operator Interface And Wire Drive Inst...

Page 16 - Process

OM-217 834 Page 12 4-5. Rear Panel Connections Ref. 803 503-A 1 9-Pin Network Receptacle 2 Motor Control/Shielding Gas Valve Receptacle 3 Rating Label Location 1 2 3 4-6. 9-Pin Network Receptacle Information 9 Pin Pin Information A Capacitor C1 to ground B Shield G F C Volt sense H G E F D Can low I...

Page 21 - Program

OM-217 834 Page 17 5-4. Program Push Button 1 3 Program 2 1 Program Display The number of the active program is displayed.2 Program Push Button 3 Program Push Button LED The LED lights to indicate that programs can be changed using the Adjust knob.Momentarily press button to illuminate LED. To chang...

Page 23 - Adjust

OM-217 834 Page 19 5-7. Feeder Set Up Push Button 1 Feeder Set Up Push Button LED 2 Feeder Set Up Push Button • Press button to choose Sequence. Feeder Set Up push-button LED will illuminate. 3 Sequence LED • When the Feeder Set Up button is pressed once, the Sequence LED will illuminate and the upp...

Page 24 - Wire Description

OM-217 834 Page 20 5-9. Process Set Up Push Button • Press the Process Set Up push button the first time will illuminate the button LED and the Process LED. The upper and lower displays will be used for Accu-pulse and only the lower display for MIG, Pulse and RMD (optional) to show the current proce...

Page 31 - Notes

Page 39 - (Equipment with a serial number preface of “LG” or newer)

Warranty Questions? Call 1-800-4-A-MILLER for your local Miller distributor. miller_warr 2006 − 01 Your distributor also gives you ... Service You always get the fast, reliable response you need. Most replacement parts can be in your hands in 24 hours. Support Need fast answers to the tough welding ...

Page 40 - Please complete and retain with your personal records.; Contact a DISTRIBUTOR or SERVICE AGENCY near you.; For Service

PRINTED IN USA © 2006 Miller Electric Mfg. Co. 2006 − 01 Miller Electric Mfg. Co. An Illinois Tool Works Company 1635 West Spencer Street Appleton, WI 54914 USA International Headquarters − USA USA Phone: 920-735-4505 Auto-Attended USA & Canada FAX: 920-735-4134 International FAX: 920-735-4125 E...

Miller Remote Operator Interface - Manual

Table of Contents:

Summary

Other Miller Models