Miller 350 - Manual

Miller 350

Miller 350 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
Page: / 51

Table of Contents:

  • Page 2 – LIMITED WARRANTY
  • Page 3 – ERRATA SHEET; AMENDMENT TO SECTION 2— INSTALLATION; Do not touch live electrical parts.; Connections; in this installation. Retain cord for future use.
  • Page 5 – Add Figure 2-4. Arc Failure Light Connections; Figure 2-4. Arc Failure Light Connections; Add the following Step to Section 5-1
  • Page 8 – Circuit Diagram
  • Page 9 – ir
  • Page 11 – AMENDMENT TO PARTS LIST; Amend Parts List as follows:; Ti; warning general precautionary; ii
  • Page 12 – Parts Lists Continued; Added; reed relay; ~First digit represents page no; digits following; dash represent item no.
  • Page 13 – TABLE OF CONTENTS; General Information And Safety
  • Page 14 – Model; Figure 1
  • Page 15 – SECTION 2; The location should allow room to open and remove
  • Page 16 – disconnect switch in open position, removing fuses; from fuse; Lockout/tagging procedures consist of padlocking line
  • Page 17 – four-socket Amphenol plug; into matching receptacle on computer interface,; Connect the twistlock receptacles to the mat-; from fuse box, or shutting off and red-tagging circuit; breaker or; other disconnecting device.
  • Page 18 – Locate terminal strip 2T.; IMPORTANT: The Inductance control is disabled; SECTION 3; Figure 3
  • Page 19 – Fuse Protection; The interface is protected from damage due to an inter-; SECTION 4; Figure 4
  • Page 20 – weld is completed, the wire stick check is performed to; SECTION 5; INSPECTION AND UPKEEP
  • Page 22 – Figure 5
  • Page 25 – USE OF INDICATOR LIGHTS FOR TROUBLESHOOTING; IF; IF; IF; Arc Failure Indicator Ligl~; Check display board PC4.
  • Page 32 – Yay; PARTS
  • Page 34 – Item; Figure A; Part; Description; Control Box; HEAT SINK; Quantity
  • Page 36 – II liD Ii LI; LID Ii II Dli; COMPONENTS TO BE REPLACED; Figure B
  • Page 39 – Figure Cl
  • Page 40 – BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN
  • Page 41 – Figure C2
  • Page 43 – Al; Cl; III; Figure C3
  • Page 44 – ASSEMBLY; LU; COMPONENTS TO BE REPLACED BY; Figure C4
  • Page 45 – mtg hole; Figure D
  • Page 46 – appearing later in this manual.; WARNING: ELECTRIC SHOCK; ging procedures before making interconnections.; disconnecting device.; The Inductance control; is disabled when operating in the CC (constant current) mode.
  • Page 47 – unit
  • Page 48 – AMENDMENT TO SECTION 5- MAINTENANCE & TROUBLESHOOTING; Amend Figure 5-3. Circuit Diagram For Computer interface; DALE
  • Page 49 – Amend Figure 5-6. Circuit Diagram For Interface Board PC3
  • Page 50 – uu
  • Page 51 – amp
Loading the manual

Y8y7?~i

Read and understand the entire

contents of both this manual and the power source
manual used with this unit, with special eutiphasis
on the safety material throughout both manuals,
before installing, operating, or maintaining this
equipment. This unit and these instructions are for

use only by persons trained and experienced in the

safe operation of welding equipment. Do not allow

untrained persons to install, operate, or maintain
this unit. Contact your distributor if you do not fully
understand these instructions.

OWN ER’S

MANUAL

Effe~ti.

E

With SanE I Fic.

..

H1:33:~’ I

MODEL

MR-5/ARC PAKTM 350

COMPUTER INTERFACE

GAS/CURRENT SENSING

CONTROL

+5

millER

MILLER ELECTRIC MFG. Co.

718 S BOUNDS ST, P 0 Box 1079

APPLETON, WI 54912 USA

ADDITIONAL COPY PRICE 95 CENTS

NWSA CODE NO. 4579

PRINTED IN U S A

IMPORTANT:

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - LIMITED WARRANTY

LIMITED WARRANTY 4; 4; 4; 4! 4; 4; ~Ji 4~ 1. 2. < 3. 4. ~ 7. This warranty supersedes all previous MILLER warranties and is exclusive with no other guarantees or warranties expressed or implied LIMITED WARRANTY Subject to the terms and condi- tions hereof, Miller Electric Mfg. Co., Appleton, Wisc...

Page 3 - ERRATA SHEET; AMENDMENT TO SECTION 2— INSTALLATION; Do not touch live electrical parts.; Connections; in this installation. Retain cord for future use.

ERRATA SHEET AMENDMENT TO SECTION 2— INSTALLATION A WARNING: ELECTRIC SHOCK can kill. 0 Do not touch live electrical parts. A. CVICC Connections A 1. Locate terminal Strip 2T. May 31,1990 ~OM.882j After this manual was printed, refinements In equipment design occurred. This sheet lists exceptionsto ...

Page 5 - Add Figure 2-4. Arc Failure Light Connections; Figure 2-4. Arc Failure Light Connections; Add the following Step to Section 5-1

Add Figure 2-4. Arc Failure Light Connections Jig Terminal Strip 2 Common Robot control Unit weld Alarm Robot Control Unit Computer Interface 2TF +24VDC 2TG 2TL Arc Failure Indicator Light To Voltage Source (115VAC, 24VAC, 24VDC) -rj 2TF ~— Arc Failure Indicalor Light TA-il 5 648 Figure 2-4. Arc Fai...

Other Miller Models

All Miller Other