Miele KM 7373 FL - User Manual

Warning and Safety instructions 8 Safety with children  Children under 8 years of age must be kept away from the hob un- less they are constantly supervised.  Children over 8 years of age may use the hob without supervision if its operation has been clearly explained to them and they are ableto us...

Warning and Safety instructions 9 Technical safety  Unauthorised installation, maintenance and repairs can cause con- siderable danger for the user. Installation, maintenance and repairsmust only be carried out by a Miele authorised technician.  Damage to the hob can compromise your safety. Check ...

Warning and Safety instructions 11 Correct use  The hob gets hot when in use and remains hot for a while after be- ing switched off. There is a danger of burning until the residual heatindicators go out.  Oil and fat can overheat and catch fire. Do not leave the hob unat- tended when cooking with ...

Warning and Safety instructions 14 Cleaning and care  Do not use a steam cleaning appliance to clean this hob. The steam could reach electrical components and cause a short cir-cuit.  If the hob is installed above a pyrolytic oven or cooker, do not use the hob during a pyrolytic cleaning programme...

Sustainability and environmental protection 15 Energy saving tips - Cook in covered pots and pans if pos- sible. This prevents heat escaping un-necessarily. - Cook with as little water as possible.- Once food has come to the boil or the pan is hot for frying, reduce the heatto a lower power level. -...

Familiarisation 16 Your hob KM 7360 FR, KM 7360 FL a Cooking zone with Booster function b Cooking zone with Booster function c Cooking zone with Booster function d Controls and indicators

Familiarisation 20 Controls and display g b d e  a b f h i k j c l m p o n a Hob On/Off sensor control b Numerical display sensor controls– To set the power level– To set the times c Flex cooking zones sensor control (depending on model)For manual connection/disconnection of Flex cooking zones d St...

Familiarisation 22 Cooking zones KM 7360 FR, KM 7360 FL Cooking zone Ø  in cm 1 Max. rating in watts for 230 V 2 Linked cooking zone 3  14–28 NormalBooster 2300 3000 -  11–22 NormalBooster 2300 3000   9–16 NormalBooster 13501850  Total 6600 1 Cookware with a base diameter within the given range...

Familiarisation 26 Power management Total power The hob has a maximum total permittedpower consumption which cannot beexceeded for safety reasons. You can re-duce the maximum total permittedpower consumption (see “Adjusting set-tings”).The higher the total permitted powerconsumption of the hob, the ...

Familiarisation 27 Operating principles Hob when switched off When the hob is switched off, you canonly see the printed symbols for thesensor controls and the numerical dis-play. More sensor controls light upwhen the hob is switched on. Operation a Sensor controls and indicators This ceramic glass h...

Familiarisation 28 Networking Your hob is equipped with an integratedWiFi module. The hob can be connectedto your home WiFi network or simply toyour Miele cooker hood. Miele@home After installing the Miele app on a mo-bile device, you can do the following: - Call up information on the operating stat...

Familiarisation 29 Functions Con@ctivity 3.0 Con@ctivity 3.0 is the direct commu-nication system between your hob and aMiele cooker hood. Communication isachieved by means of networking.Con@ctivity 3.0 enables the cookerhood to operate automatically depend-ing on the operating status of your hob.Fur...

Familiarisation 31 Safety switch-off Sensor controls are covered Your hob will switch off automatically ifone or several of the sensor controls re-main covered for longer than10 seconds, for example, by finger con-tact, food boiling over or by an object.   will appear in the timer display for a few...

Familiarisation 32 Overheating protection In order to prevent the hob from beingdamaged by excessive temperatures,the overheating protection mechanismintervenes in one of the following ways: Overheating protection measures - If the Booster function is switched on, it will stop. - The set power level...

Commissioning 33 Unpacking the hob  Please stick the data plate for the ap-pliance, supplied with this document-ation, in the space provided in the“Customer Service Department” sec-tion of this booklet.  Remove any protective foil and stick-ers. Cleaning the hob for the firsttime  Before using fo...

Commissioning 34 Miele@home Installing the Miele app The ability to use the Miele app de-pends on the availability of theMiele@home service in your country.For information about availability, pleasevisit www.miele.com.The Miele app is available free of chargefrom the Apple App Store ® or from the Go...

Commissioning 35 Connecting via the Miele app - A home WiFi network is available.- The signal of your WiFi network is sufficiently strong in the placewhere your hob is installed. - There is no direct WiFi connection between the hob and a Mielecooker hood (Con@ctivity 3.0). - The Miele app is install...

Commissioning 36 Cancelling the process  Touch any sensor control. Resetting settings Reset the settings if you are disposingof your hob, selling it or putting a usedhob into operation. This is the only wayto ensure that all personal data hasbeen removed and the previous ownerwill no longer be able...

Commissioning 37 Establishing a direct connectionwith the cooker hood The hob requires max. 2 W in networkedstandby. Availability of the WiFi connection The WiFi connection shares a frequencyrange with other appliances (includingmicrowave ovens and remote controltoys). This can give rise to sporadic...

Operation 39 Safety notes for operation  Risk of fire with overheated food. Unattended food can overheat and catch alight.Do not leave the hob unattended whilst it is being used.  Risk of burning due to hot cooking zones. The cooking zones will be hot after use.Do not touch the cooking zones while...

Operation 40 Switching the hob on  Touch the   sensor control. Further sensor controls will light up. If no further entry is made, the hob willswitch itself off after a few seconds forsafety reasons. Switching off a cooking zone/the hob Switching the hob off  To switch off the hob and all the coo...

Operation 41 Power level Setting the power level Permanent pan recognition is activatedas standard (see “Adjusting settings”).When the hob is switched on and youplace an item of cookware on a cookingzone, the cooking zone indicator startsto flash.  Place the cookware on the cookingzone you want to ...

Operation 42 Booster Activating the Booster When the Booster function is activated,the settings for the linked cooking zonemay be changed, see “Familiarisation –Power management”.The Booster function can be used on amaximum of two cooking zones at thesame time.The Booster function is active for a ma...

Operation 43 Auto heat-up The heat-up time depends on whichcontinued cooking setting has beenchosen: Continued cook- ing setting* Heat-up time [min:sec] 1 Approx. 0:15 1. Approx. 0:15 2 Approx. 0:15 2. Approx. 0:15 3 Approx. 0:25 3. Approx. 0:25 4 Approx. 0:50 4. Approx. 0:50 5 Approx. 2:00 5. Appro...

Operation 44 Timer Setting timer durations A duration of between 1 minute ( : ) and 9 hours 59 minutes ( : ) can be set.Durations of up to 59 minutes areshown in minutes (00:59) and durationsof more than 60 minutes are shown inhours and minutes.Durations are entered using the numer-ical displa...

Operation 46 System lock Activating the system lock All sensor controls are locked. A setminute minder time will continue tocount down.  Touch the   sensor control for 6 seconds. The seconds can be seen countingdown in the timer display. When thistime has elapsed,   will appear in the timer dis...

Operation 47 Activating the Recall function  Switch the hob on again.  Immediately after switching the hobon, touch one of the flashing cookingzone sensor controls. Activating /deactivating theKeeping warm function The Keeping warm function cannot beused to reheat food that has gone cold.  Touch ...

Operation 48 Activating /deactivating demomode  Switch the hob on.  Press the 0 and 2 sensor controls onthe numerical display at the sametime for 6 seconds. The following will flash in the timer dis-play for a few seconds: -  alternating with  (demo mode activated) or -  alternating with ...

Setting ranges for the power levels 49 The hob is programmed with 9 power levels at the factory. If you wish to fine-tune asetting, you can extend the power level range to 17 power levels (see “Adjustingsettings”). Setting range Factory set- ting (9 power levels) Extended set- ting (17 power levels)...

Good to know 50 How induction hobs work An induction coil is located under eachinduction cooking zone. The coil createsa magnetic field that reacts directly withthe base of the pan and heats it up. Thecooking zone itself is heated up indir-ectly by the heat given off by the pan.An induction cooking ...

Good to know 51 Pans Suitable cookware - Stainless steel cookware with a mag- netic base - Enamelled steel cookware- Cast iron Please be aware that the properties ofthe cookware base can affect the even-ness with which the food heats up (e.g.when making pancakes). The base ofthe pan must be able to ...

Adjusting settings 52 Accessing programming mode The hob is switched off.  Touch and hold the  and   sensor controls until the + sensor control lights up and   appears in the timer display. After a few seconds :  (Programme 01) will flash alternately with :  (Code) in the timer display. S...

Cleaning and care 55 Safety notes on cleaning and care  Risk of burns due to hot surfaces. All parts of the hob may be hot after use.Switch the hob off.Allow the hob to cool down before cleaning it. All surfaces could be discoloured or damaged if unsuitable cleaningagents are used or if residues fr...

Cleaning and care 56 When to clean  Clean the hob after every use. Removing light soiling  Clean the entire ceramic surface ofthe hob with a damp, soft cloth and asolution of water and a little washing-up liquid. Please follow the cleaningagent manufacturer ’s instructions. Removing stubborn soili...

Troubleshooting 57 Messages in the display Problem Cause and remedy The  symbol lights up or flashes alternately withthe set power level or  in one of the cookingzone indicators. No cookware is present on the cooking zone. Unsuitable cookware is present on the cooking zone. The diameter of the bas...

Troubleshooting 58 Problem Cause and remedy   will flash alternately with   ,  or   in the timer display. The fan is blocked or defective.  Make sure it has not been blocked by an object.  Remove the obstruction.  If this fault message continues to appear in the dis-play, contact the ...

Troubleshooting 59 Unexpected behaviour Problem Cause and remedy Power level 9 is auto-matically reduced if youalso set power level 9 forthe connected cookingzone. Operating both zones at power level 9 exceeds thepermitted maximum power for the two zones.  Use a different cooking zone. A cooking zo...

Troubleshooting 60 Unsatisfactory results Problem Cause and remedy The food in the pan doesnot heat up when theAuto heat-up function isswitched on. A large amount of food is being heated up.  Start cooking at the highest power level and thenturn down to a lower one manually later on. The pan is not...

After sales service 61 Information to help you rectify faults yourself and about Miele spare parts can befound at www.miele.com/service. Contact in the event of a fault In the event of a fault which you cannot remedy yourself, please contact your Mieledealer or Miele Customer Service. You can book a...

After sales service 62 Note for test institutes Test food acc. to EN 60350-2 9 power levels are programmed at the factory.For testing in accordance with the above standard, programme the hob to the ex-tended power level setting (see “Adjusting settings”). Test food  Pan base (mm) Lid Power level Pr...

Optional accessories 63 Cookware Miele offers a wide range of cookware.These have all been optimised for Mieleappliances in terms of functionality anddimensions. Detailed information isprovided on the Miele website. Cleaning and care products Ceramic and stainless steel hobcleaner 250 ml Removes hea...

Installation *INSTALLATION* 64 Safety notes for installation  Risk of damage from incorrect installation. Incorrect installation can cause damage to the hob.The hob must only be installed by a qualified specialist.  Risk of electric shock from mains voltage. Incorrect connection to the mains suppl...

Installation *INSTALLATION* 65 Additional safety notes for surface-mounted installation  Damage caused by incorrect installation. Using sealant under the hob could result in damage to the hob andthe worktop if the hob ever needs to be removed.Do not use sealant between the hob and the worktop.The s...

Installation *INSTALLATION* 66 Additional safety notes for flush-fit installation  Damage from unsuitable sealant. Unsuitable sealant can damage natural stone.For natural stone worktops and natural stone tiles, only use siliconesealant that is specially formulated for natural stone. Follow themanuf...

Installation *INSTALLATION* 67 Safety distances Safety distance above the hob The following must be ensured betweenthe hob and the cooker hood above it: - The safety distance specified by the manufacturer of the cooker hood mustbe maintained. - When two or more appliances which have different safety...

Installation *INSTALLATION* 68 Safety distance behind and to the sideof the hob The minimum safety distances shownbelow must be maintained between theappliance and a tall unit or wall: - Between the back    of the worktop cut-out and the rear edge of the work-top:50 mm and - On the right side    b...

Installation *INSTALLATION* 69 Safety distance underneath the hob To install the hob while maintaining thesafety distances, you can choose from3 variants: 1. Without intermediate shelf or base panel 2. With intermediate shelf3. With an air intake-optimised base panel Further instructions are describ...

Installation *INSTALLATION* 70 1. Without intermediate shelf or base panel To ensure sufficient ventilation to the hob, a minimum safety distance must be leftbetween the underside of the hob and any drawer or oven.The minimum safety distance between the underside 1 of the hob and: - Upper edge of dr...

Installation *INSTALLATION* 71 3. Air intake-optimised base panel The performance of the hob depends on the ventilation.The air intake-optimised base panel has openings where the fans are positioned.This section contains instructions for creating an air intake-optimised base panel. ≤ 40 mm ≥ 45 mm ≥...

Installation *INSTALLATION* 72 Positions and cut-outs of the ventilation openings Y1.1 X1.1 X2.1 Y2.1 Not to scale. View from above. Surface-mounted cut-out shown.Also applies to flush-fit installation. a Middle of the cut-out height b Middle of the cut-out width c Cut-out for fan, round (Ø 55–70 mm...

Installation *INSTALLATION* 73 Safety distance from the niche cladding If niche cladding is installed, a minimum safety distance must be maintainedbetween the worktop cut-out and the cladding. High temperatures can alter ordamage these materials. Flush-fit installation Surface-mounted installation a...

Installation *INSTALLATION* 74 Building-in dimensions for surface-mounted installation KM 7360 FR, KM 7361 FR All dimensions are given in mm. a Front b Mains connection boxThe mains connection cable (L = 1440 mm) is supplied loose

Installation *INSTALLATION* 80 Installation dimensions for flush-fit installation KM 7360 FL, KM 7361 FL All dimensions are given in mm. a Front b Mains connection boxThe mains connection cable (L = 1440 mm) is supplied loose c Stepped cut-out, natural stone worktop d Wooden batten 12 mm (not suppli...

Installation *INSTALLATION* 83 Installing a surface-mountedhob  Create the worktop cut-out. Remem-ber to maintain the minimum safetydistances (see “Installation – Safetydistances”).  Seal any cut surfaces on wooden worktops with a special varnish, silic- one sealant or resin to prevent thewood fro...

Installation *INSTALLATION* 85 Electrical connection  Risk of damage from incorrect connection.Unauthorised installation, mainten-ance and repairs can cause consider-able danger for the user.Miele cannot be held liable for dam-age or injury caused by unauthorisedinstallation, maintenance or repairw...

Installation *INSTALLATION* 86 Disconnecting from the mains  Risk of electric shock. There is a risk of electric shock if theappliance is connected to the mainssupply during repair or service work.After disconnection, ensure the appli-ance cannot be switched back on bymistake. To disconnect the app...

Installation *INSTALLATION* 87 Wiring diagram Some connection methods are notpermitted in all installation locations.Ensure compliance with national reg-ulations and any additional regula-tions issued by the local electricityprovider. The maximum load per connected liveconductor is 3650 W.The first ...

Installation *INSTALLATION* 88 Product data sheets The following data sheets apply to the models described in this operating instruc-tion manual. Information for domestic electric hobs In acc. with regulation (EU) No. 66/2014 MIELE Model name/identifier KM 7360 FR, KM 7360 FL Number of cooking zones...

Installation *INSTALLATION* 90 EU Conformity declaration Miele hereby declares that this ceramic induction hob complies with Directive2014/53/EU. The complete text of the EU declaration of conformity is available from one of thefollowing internet addresses: - Products, Download from www.miele.ie- Fo...

United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TWTel: 0330 160 6600, Internet: www.miele.co.uk, E-mail: [email protected] Australia Miele Australia Pty. Ltd.ACN 005 635 398ABN 96 005 635 398Level 4, 141 Camberwell RoadHawthorn East, VIC 3123Tel: 1300 464 353E-mail: [em...