Page 2 - Contents; Language
Contents 2 Warning and safety instructions ................................................................................ 6 Notes on the operating instructions ......................................................................... 14 Notes on the layout.............................................
Page 3 - Caring for the environment
Contents 3 Remote Update .............................................................................................................. 38 SmartStart....................................................................................................................... 39 EcoStart ......................
Page 4 - Timer
Contents 4 Manual detergent dispensing ....................................................................................... 70 Dispensing detergent ............................................................................................... 70 Adding detergent ....................................
Page 5 - Service
Contents 5 Water drainage fault ....................................................................................................... 105 Fault in the AutoDos (automatic dispensing)............................................................. 106 Spray arm fault.......................................
Page 6 - Warning and safety instructions; Appropriate use
Warning and safety instructions 6 This dishwasher conforms to current safety requirements.Inappropriate use can, however, lead to personal injury andmaterial damage.Please observe the installation sheet and read the operatinginstructions carefully before setting up the dishwasher and using itfor the...
Page 7 - Technical safety
Warning and safety instructions 7 Children aged 8 and older may only use the dishwasher without supervision if they have been shown how to use it in a safe manner.Children must be able to understand and recognise the possibledangers caused by incorrect operation. Children must not be allowed to ...
Page 8 - Temporary or permanent operation on an autonomous power
Warning and safety instructions 8 Temporary or permanent operation on an autonomous power supply system or a power supply system that is not synchronisedwith the mains power supply (e.g. island networks, back-up systems)is possible. A prerequisite for operation is that the power supplysystem compl...
Page 10 - Correct installation
Warning and safety instructions 10 The water-connection pressure needs to be between 50 and 1,000 kPa. A damaged dishwasher could be dangerous. If the dishwasher gets damaged, switch it off at the mains immediately and call your Mieledealer or Miele Service. While the appliance is under warran...
Page 11 - Correct use
Warning and safety instructions 11 If the dishwasher is being used behind closed furniture fronts (e.g. doors), ensure that the automatic door opening mechanism is notblocked. The housing units used must be sufficiently resistant to moisture. The installation space must be well ventilated. The d...
Page 12 - Accessories and spare parts
Warning and safety instructions 12 Crockery may be very hot at the end of the programme. Allow the dishes to cool until they are comfortable enough to handle beforeunloading them. Only use detergent and rinse aid formulated for domestic dishwashers. Do not use washing-up liquid. Do not use any...
Page 13 - Miele will guarantee to supply functional spare parts for a; Transport; Damage to the dishwasher can compromise your safety. Before
Warning and safety instructions 13 Miele will guarantee to supply functional spare parts for a minimum of 10 years and up to 15 years following the discontinuationof your dishwasher. Transport Damage to the dishwasher can compromise your safety. Before using the dishwasher, check it for any visi...
Page 14 - Notes on the operating instructions; Notes on the layout; Warnings; Information which is important; Notes; Select the desired setting and press; Display
Notes on the operating instructions 14 These operating instructions apply toseveral different dishwasher models ofdifferent heights. The different dishwasher models will benamed as follows: normal = dishwasher measuring80.5 cm high (built-in appliance) or84.5 cm high (freestanding appliance) XXL = d...
Page 15 - Scope
Scope 15 The appliance is supplied with: - Dishwasher- Operating instructions for operating the dishwasher - Installation sheet for installing the dishwasher - Other installation accessories for installing the dishwasher (seeinstallation sheet) - Funnel for filling the dishwasher salt- Door opening ...
Page 16 - Guide to the appliance; Appliance overview
Guide to the appliance 16 Appliance overview a Door locking pins b Top spray arm c 3D MultiFlex cutlery tray d Upper basket (depending on model) e Middle spray arm f Aeration valve g Bottom spray arm h Filter combination i Salt reservoir j Data plate k Rinse aid reservoir l Detergent compartment m A...
Page 17 - Lower basket; Glass holder
Guide to the appliance 17 Lower basket a Glass holder b FlexCare Glass & Bottle c MultiClip d XL-Assist e Hinged spikes f StrawClean
Page 18 - Control panel; sensor control
Guide to the appliance 18 Control panel a Optical in-operation indicator lightFor indicating an ongoing washprogramme when the door is closed. b On/Off sensor control For switching the dishwasher on andoff. c MobileStart sensor control for activating /deactivating theMobileStart option d T...
Page 19 - Display functions; OK
Guide to the appliance 19 Display functions The display is used to select or set thefollowing: - The programme- Options- The timer- The Settings The display can show the following: - The programme name- The programme stage- The estimated time left for the programme to run - The energy and water cons...
Page 20 - Main menu; Lists; Auto; Numerical values; Use the
Guide to the appliance 20 Examples of how to operate theappliance Main menu Use the Back sensor control to switch from the Programme menu tothe main menu.In the main menu, you can selectbetween the Programmes, Settings andInformation menus.In the Programmes menu, you canselect the programmes.You ...
Page 21 - Disposing of your old appliance
Caring for the environment 21 Disposing of the packagingmaterial The packaging material is used forhandling and protects the appliancefrom transport damage. The packagingmaterial used is selected from materialswhich are environmentally friendly fordisposal and can generally be recycled.Recycling the...
Page 22 - Before using for the first time; Opening the door; The door will open a little.
Before using for the first time 22 Every dishwasher is tested at thefactory. There will be residual water inthe appliance from this test. It is notan indication that the dishwasher hasbeen used previously. Opening the door In some programmes the doorautomatically opens slightly to assistthe drying p...
Page 23 - Door opening mechanism
Before using for the first time 23 Door opening mechanism If the door will not open when knockedor if there is a power failure, the doorcan be opened manually with the dooropening mechanism supplied with thedishwasher. 1 2 Push the door opening mechanisminto the gap between the dishwasherfront and...
Page 24 - In order to use it you will need:; Availability of the WiFi connection; or from the Google Play StoreTM.
Before using for the first time 24 Miele@home Your dishwasher is equipped with anintegrated WiFi module. In order to use it you will need: - A WiFi network- The Miele app- A Miele user account The user account can be created via the Mieleapp. The Miele app will guide you as youconnect your dishwashe...
Page 25 - Basic settings; Switching on the dishwasher; Setting the time of day; Setting the water hardness level
Before using for the first time 25 Basic settings Switching on the dishwasher Open the door. Switch the dishwasher on usingthe sensor control. The welcome screen will appear whenthe dishwasher is switched on and thewelcome melody will sound. For further information about thedisplay functional...
Page 26 - Activating AutoDos; and; Select
Before using for the first time 26 The dishwasher is programmed at thefactory for a water hardness level of2.5 mmol/l (14 °dH – German scale). Set the water hardness level in yourarea and confirm using OK . See the “Settings” chapter, “Waterhardness” section for moreinformation. Activating AutoDos...
Page 27 - Dishwasher salt; not; Damage to the water softener
Before using for the first time 27 Dishwasher salt In order to achieve good cleaningresults, the dishwasher needs tooperate with soft water. Hard waterresults in the build-up of calciumdeposits on crockery and on the washcabinet walls. Mains water with a water hardness levelhigher than 0.9 mmol/l (5...
Page 28 - Filling the salt reservoir; Risk of corrosion due to saline; programme without load items in
Before using for the first time 28 Filling the salt reservoir Before filling the salt reservoir for thefirst time, you must fill it withapprox. 1.5 l of water to enable the saltto dissolve.Once the dishwasher has beencommissioned, there is alwayssufficient water in the salt reservoir. Remove the l...
Page 29 - Refilling salt; When the refill reminder; Confirm with
Before using for the first time 29 Refilling salt When the refill reminder Add salt and run the “Rinse salt” programme appears in the display, wait until theend of the programme and then refillthe salt reservoir. Confirm with OK . The salt refill indicator will go out. Risk of corrosion du...
Page 30 - Rinse aid; Washing-up liquid or detergent
Before using for the first time 30 Rinse aid Rinse aid is necessary to ensure thatwater does not cling and leave marks oncrockery during the drying phase, andhelps crockery dry faster after it hasbeen washed. Rinse aid is poured into the containerand the amount set is dispensedautomatically. Washi...
Page 31 - Adding rinse aid
Before using for the first time 31 Adding rinse aid Press the yellow button on the lid of the rinse aid reservoir. The lid will spring open. Fill with rinse aid until the filling levelindicator (arrow) changes to a darkcolour while the door is horizontallyopen. The rinse aid reservoir holdsap...
Page 32 - Opening the settings menu; Changing settings; Closing the settings menu
Settings 32 You can alter the dishwasher ’s controlsto suit changing requirements byadjusting the settings.The settings can be altered at anytime. Opening the settings menu Switch the dishwasher on using the sensor control. The Programmes menu will appear inthe display. For further information ...
Page 33 - The flag after the word; Time; Setting the clock format; You can set the current time of day.
Settings 33 Language The display can be set to appear in oneof several different languages.You can change the language used inthe display and also the country via the Language sub-menu. The flag after the word Language serves as a guide if a language that youdo not understand has been set.I...
Page 34 - Water hardness; Setting the Dosage amount
Settings 34 Water hardness Your dishwasher is fitted with a watersoftener. - You should programme the dishwasher to the correct waterhardness for your area. - Your local water authority will be able to advise you of the water hardnesslevel in your area. - Where the water hardness fluctuates e.g. bet...
Page 35 - ECO
Settings 35 Rinse aid You can adjust the rinse aid dosage forbest results. The rinse aid dosage can be set from 0to 6 ml. 3 ml is the factory default setting.The rinse aid dosage can turn out to behigher than the set value due to theautomatic adjustment of theprogramme.If spots appear on crockery an...
Page 36 - Performing Scan & Connect
Settings 36 Miele@home Your dishwasher is equipped with anintegrated WiFi module.You can connect your dishwasher toyour WiFi network. This will increase the energyconsumption, even when thedishwasher is switched off.The “Settings” and “Miele@homesettings” menus will be added asadditional menu option...
Page 38 - MobileStart; Remote Update; Activating /deactivating
Settings 38 personal data has been removed andthe previous owner will no longer beable to access the dishwasher. Select the Reset network configuration? menu option. Select the Yes option. Remote control This menu option will only bedisplayed if you have connected yourdishwasher to your WiFi ne...
Page 39 - Running a RemoteUpdate
Settings 39 Running a RemoteUpdate Information about the content andscope of a RemoteUpdate will beprovided in the Miele app. A message will appear in yourdishwasher display if a software updateis available.You can install the update immediatelyor postpone it until later. When theappliance is switch...
Page 40 - Setting the energy tariff times
Settings 40 EcoStart In order to run your dishwasher in themost economical way, you can use the EcoStart option to take advantage of your electricity supplier ’s cheaperenergy tariffs (see “Options” chapter,“Timer ” section). With this option selected, yourdishwasher will start automatically atyour...
Page 41 - Changing the energy tariff times; Deleting the energy tariff times; Temperature
Settings 41 Changing the energy tariff times You can change the start, end or priorityof an energy tariff time. Select an energy tariff time to changefrom T1 to T3. Select the setting you want tochange. Change the setting and confirm with OK . The selected settings are displayed.The change wil...
Page 42 - Volume; Buzzer in the event of a fault; Off; Welcome melody; Refill reminders
Settings 42 Volume A buzzer sequence will sound at the endof a programme or if there is a fault aslong as the buzzers are activated. Buzzer in the event of a fault In the event of a fault, the alarm tonewill sound four times at intervals with ashort pause between each set of tones. The alarm tone th...
Page 43 - AutoOpen; Risk of injury due to door opening; nd interim rinse; Knock2open
Settings 43 AutoOpen In some programmes the doorautomatically opens slightly to assistthe drying process.This function can be deactivated if youwish. However, this negatively affectsthe drying process in most cases. Risk of injury due to door opening automatically.The door may open automatically a...
Page 44 - Hygiene cycle; Water connection; Legal information
Settings 44 Hygiene cycle If you mainly use low temperatureprogrammes (< 50 °C), there is a risk ofbacteria and unpleasant odours buildingup in the wash cabinet (see “Cleaningand care – Hygiene cycle”).If this function is switched on, amessage will be displayedrecommending the use of a hightemper...
Page 45 - in the appliance for the Open
Settings 45 Copyrights and licences foroperator and control software Miele uses their own and third partysoftware which is not subject to any so-called Open Source Licence for theoperation and control of the appliance.This software/these softwarecomponents are protected by copyright.The copyright po...
Page 46 - Showroom
Settings 46 Showroom For demonstration purposes only. The dishwasher is equipped with ademo mode for showroom use. Factory default You can reset all dishwasher settings tothe factory default settings.WiFi module settings (where applicable)have to be reset separately (see“Settings – Miele@home”). S...
Page 47 - Economical dishwashing
Caring for the environment 47 Economical dishwashing This dishwasher is exceptionallyeconomical in its use of water andelectricity. You can make the most of yourappliance by following these tips: - Washing in a dishwasher generally uses less water and energy thanwashing by hand. - There is no need t...
Page 48 - Estimated consumption; Displaying consumption
Caring for the environment 48 EcoFeedback consumptionindicator You can display information about theenergy and water consumption of yourdishwasher (see “Settings –Consumption indicator ”).The following information may appearon the display: - Estimated energy and water consumption before the programm...
Page 49 - Heat accumulator; water connection (see “Settings –; . Other functions will be
Caring for the environment 49 Heat accumulator This dishwasher is equipped with a heataccumulator, in which fresh water forthe programme is pre-heated andstored in order to save energy. The heataccumulator is refilled with fresh watertowards the end of each programme.The water is held here ready for...
Page 50 - Loading the dishwasher; General information
Loading the dishwasher 50 General information Remove coarse food residues fromcrockery.There is no need to pre-rinse itemsunder running water. Damage can be caused by ash, sand, wax, lubricant or paint.These substances will contaminatethe dishwasher and can then nolonger be removed.Do not wash ite...
Page 51 - Items not suitable for dishwashers:
Loading the dishwasher 51 Items not suitable for dishwashers: - Wooden cutlery and crockery or items with wooden parts: these maydiscolour and fade. The glue used inthese items is not dishwasher-proofand wooden handles may come looseafter being washed in a dishwasher. - Craft items, antiques, valuab...
Page 52 - Upper basket; Loading the upper basket; Damage due to leaking water.; Loading the FlexCare cup rack; Lower the FlexCare cup rack to do so.
Loading the dishwasher 52 Upper basket See the “Loading the dishwasher ”chapter, “Loading examples” sectionfor examples of how to load crockeryand cutlery. Loading the upper basket Damage due to leaking water. If you run the dishwasher without theupper basket, water can leak out ofthe dishwasher.O...
Page 53 - Adjusting the FlexCare cup rack
Loading the dishwasher 53 Adjusting the FlexCare cup rack You can set the height and depth of thecup rack at two different levels. so thatit can accommodate larger cups and sothat taller crockery can be placedunderneath it. Pull the cup rack upwards and click itinto the desired position (see arrow...
Page 54 - Lowering the spikes; Press the yellow lever downwards
Loading the dishwasher 54 Lowering the spikes On both right-hand rows of spikes, youcan lower every other spike to make iteasier to arrange larger crockery, e.g.cereal bowls. 1 2 Press the yellow lever downwards , and then lower the dark grey spikes . Place the bowls vertically in the rowof ...
Page 55 - Adjusting the upper basket; Pull out the upper basket.; Raise the upper basket:
Loading the dishwasher 55 Adjusting the upper basket In order to gain more space for tallerpieces of crockery in the lower basket orupper basket, the upper basket can beadjusted on 3 levels with 2 cm betweeneach level.The upper basket can also be set at anangle so that water can run off freelyfrom r...
Page 56 - Loading the lower basket; When tilted, plates up to 35 cm in
Loading the dishwasher 56 Lower basket See the “Loading the dishwasher ”chapter, “Loading examples” sectionfor examples of how to load crockeryand cutlery. Loading the lower basket Place larger and heavier items such asplates, serving platters, saucepans,bowls etc., in the lower basket. Glasses, c...
Page 57 - FlexCare Glass & Bottle
Loading the dishwasher 57 FlexCare Glass & Bottle The glass and bottle holders are used towash stemware, tall glasses and bottles. Adjusting the FlexCare Glass & Bottle You can set the glass and bottle holdersat 2 different heights. Slide the glass and bottle holder tothe desired height un...
Page 58 - Loading the FlexCare Glass & Bottle; Lean the containers into the holders.
Loading the dishwasher 58 Loading the FlexCare Glass & Bottle The glass and bottle holders can beused to keep tall, narrow and hollowcontainers, e.g. beer glasses, bottles,vases, secure during a programme. The inserts in the glass and bottleholders can be raised to make moreroom for tall glass...
Page 59 - MultiClip; Secure light items to the MultiClips.; Loading the XL-Assist; Slightly lift the XL-Assist
Loading the dishwasher 59 MultiClip The MultiClips enable you to fasten lightload items such as those made fromplastic. Secure light items to the MultiClips. Make sure that crockery does notobstruct the middle spray arm. XL-Assist The XL-Assist is used to secure largeload items, e.g. pots and pans...
Page 60 - StrawClean; For the best cleaning results, use; Loading the StrawClean
Loading the dishwasher 60 StrawClean The drinking straw holder canaccommodate 5 straight or bent strawswith a maximum outer diameter of12 mm.Straws with a length of 10–25 cm areheld particularly securely.For the best cleaning results, use strawsmade of glass or plastic with an innerdiameter of more ...
Page 61 - Adjusting the StrawClean; and remove it
Loading the dishwasher 61 Adjusting the StrawClean The adjustable bracket of theStrawClean ensures that the straws areheld securely. Longer straws are heldparticularly securely. To accommodate long straws, pull upthe StrawClean bracket until it locksinto the upper position. To adjust the bracket...
Page 62 - Cutlery tray; Loading the 3D MultiFlex tray
Loading the dishwasher 62 Cutlery tray See the “Loading the dishwasher ”chapter, “Loading examples” sectionfor examples of how to load crockeryand cutlery. Load the cutlery into the 3D MultiFlextray. Loading the 3D MultiFlex tray To make unloading easier, cutlery shouldbe grouped in zones, one for...
Page 63 - Loading examples; Dishwashers with cutlery tray
Loading the dishwasher 63 Loading examples Dishwashers with cutlery tray Upper basket Lower basket
Page 65 - Detergent; Active ingredients; Risk of damage due to unsuitable
Detergent 65 Active ingredients Risk of damage due to unsuitable detergents.Detergents that are not suitable fordomestic dishwashers can causedamage to the dishwasher or to theload items.Only use detergents formulated fordomestic dishwashers. Modern detergents contain variousactive ingredients, th...
Page 66 - Risk of chemical burns from; Detergent dosage
Detergent 66 Risk of chemical burns from detergent.Dishwasher detergents can causeburning on the skin and in the eyes,nose, mouth and throat.Avoid contact with detergents. Do not inhale powder detergents. Donot swallow dishwasher detergents.Seek medical attention immediatelyif detergent has been s...
Page 67 - Automatic dispensing /AutoDos; AutoDos; Inserting a PowerDisk
Detergent 67 Automatic dispensing /AutoDos Before you can use AutoDos, you mustinsert a PowerDisk containing powderdetergent into the PowerDiskcompartment.One PowerDisk contains enoughdetergent for approx. 20 cycles,depending on the chosen programme. PowerDisks are available to orderdirectly from th...
Page 68 - This activates the
Detergent 68 Insert the new PowerDisk and press itevenly downwards until it sits flush. Close the AutoDos lid and turn it untilthe lid handle is directly below the symbol. This activates the AutoDos function. If the PowerDisk is not in the correctstarting position, it will be rotatedautomatic...
Page 70 - Manual detergent dispensing; Dispensing detergent; QuickPowerWash; Adding detergent; Press the yellow button
Detergent 70 Manual detergent dispensing Detergent must be manually dispensedif you have deactivated automaticdispensing in a programme's Extrasmenu. Dispensing detergent The detergent compartment holds amaximum of 50 ml.There are marks in the detergentcompartment as a dispensing aid: 20,30, max. Wh...
Page 72 - Operation; Touch the; Selecting a programme; sensor control to return to the
Operation 72 Switching on the dishwasher Open the stopcock, if it is closed. Open the door. Make sure the spray arms can rotatefreely. Touch the sensor control. If the dishwasher has been switchedoff for longer than 1 minute, you willneed to hold the sensor control for a bit longer (w...
Page 73 - Display of programme duration
Operation 73 Display of programme duration The estimated duration of the selectedprogramme appears on the displaybefore the programme begins. If thedoor is opened during the programme,the time left until the end of theprogramme is displayed.The displayed duration may vary for thesame programme. It i...
Page 74 - End of the programme; programmable; Energy management; sensor control for a bit
Operation 74 End of the programme At the end of a programme, the in-operation indicator light will flash slowlywith the door shut. The buzzer mightalso sound.The in-operation indicator light will goout 10 minutes after the end of theprogramme if the door is closed.The programme has ended when thedis...
Page 75 - Switching off the dishwasher; sensor; with; Risk of damage from leaking; Unloading the dishwasher
Operation 75 Switching off the dishwasher Open the door. The dishwasher can be switched offat any time using the sensor control. Switching the dishwasher off during aprogramme stops the programme. Confirm the query Switch appliance off? with Yes . You can also do this to stop an ongoingtime...
Page 76 - Interrupting a programme
Operation 76 Interrupting a programme A programme will be interrupted assoon as the door is opened. If the door is closed again, theprogramme will continue from the pointit was at before the door was opened. Risk of scalding due to hot water. During operation, water in thedishwasher may be very ho...
Page 77 - Options; Activating the timer
Options 77 Timer The timer gives you several options for starting a programme at a later time.You can set the start time or the finishtime of a programme. You can also usethe EcoStart or SmartStart functions to benefit from cheaper energy tariffs atnight. With manual detergent dispensingthe d...
Page 78 - Setting “Start at”; Setting “Finish at”
Options 78 Setting “Start at” With the Start at function, you set the exact time you want the programme tostart at. Set the hours with the sensor controls. Touch the minute number block. Use the sensor controls to enter the minutes and confirm your entry bytouching OK . The saved star...
Page 79 - Setting EcoStart; Setting SmartStart
Options 79 Setting EcoStart You can use the EcoStart function to benefit from cheaper energy tariffs atnight. Before you can use this option,you need to set up to three electricaltariff time zones (see “Settings”chapter, “EcoStart” section). Then set the latest time by which theselected programme h...
Page 80 - Changing and deleting the timer
Options 80 Set the latest time by which theselected programme has to be finished. Set the hours with the sensor controls. Touch the minute number block. Use the sensor controls to enter the minutes and confirm your entry bytouching OK . The message Waiting for SmartStart is displayed....
Page 81 - Activating MobileStart
Options 81 Activating MobileStart You can start your dishwasher remotelyusing the Miele app. To do this, you firstneed to install the app on your mobiledevice, connect the dishwasher to yourWiFi network (see “Settings –Miele@home”) and, if applicable,activate the “Remote control” setting(see “Set...
Page 82 - Guide for selecting a programme; Crockery
Guide for selecting a programme 82 1 Food such as potatoes, pasta, rice or stews can leave starchy deposits. Deposits containing protein can be left by food such as fried meat or fish. Mixed crockery including temperature-sensitive glasses and plastics Pots, pans, everyday crockery and cutlery Light...
Page 84 - Programme overview; Programme
Programme overview 84 Programme Programme sequence Pre-wash Main wash Interim rinse Final rinse Drying / AutoOpen °C °C ECO 1 - 43 42 / Auto 45–60 °C Variable programme sequence, sensor-controlled adjustment according to load size and level of soiling As required 45–60 55–70 / ComfortWas...
Page 86 - Further programmes; programme to clean it. The
Programme overview 86 Further programmes ComfortWash+ 55 °C Programme for cleaning a mixed load ofcrockery with normal household foodresidues. SolarSave Programme operating without heatingwhen the dishwasher is connected to ahot water supply of at least 45 °C (see“Installation – Water inlet”). Thisp...
Page 87 - Extras; Selecting extras; Quick
Extras 87 Selecting extras You can use extras to adjust theprogrammes.To do this, you can select or deselectthe extras in the Extras menu of aselected programme before starting it. Open the door. Switch the dishwasher on usingthe sensor control. Select a different programme ifrequired. All ...
Page 88 - IntenseZone; Extra clean
Extras 88 AutoDos The AutoDos extra can be used to switch automatic dispensing on or off(see “Detergent – Automaticdispensing”).This setting applies to all programmes. BottleClean You can select the BottleClean extra to increase the cleaning performance ofthe programmes for tall, narrow hollowcontai...
Page 89 - Cleaning and care; Cleaning the wash cabinet; Intensive 75 °C; Cleaning the control field; only; Cleaning the reflector panel
Cleaning and care 89 Check the condition of yourdishwasher regularly (approx. every4–6 months). In this way, faults andproblems can be avoided. Damage due to unsuitable cleaning agents.All surfaces are susceptible toscratching. Contact with unsuitablecleaning agents can alter or discolourthe exter...
Page 90 - Cleaning the appliance front; Damage due to soiling.
Cleaning and care 90 Cleaning the appliance front Damage due to soiling. Soiling that is left too long mightbecome impossible to remove andcould cause the external surfaces toalter or discolour.It is therefore best to remove anysoiling immediately. Clean the appliance front with a softsponge clo...
Page 91 - Cleaning the AutoDos
Cleaning and care 91 Cleaning the AutoDos If the Clean AutoDos message is displayed, check that the AutoDos isclean, and clean it if necessary, e.g.powder residues. This helps keep theAutoDos working properly. In order to ensure that the AutoDosfunction works at its best, check iteach time you repla...
Page 92 - and reinsert
Cleaning and care 92 1 2 Pull the yellow opening tag in thedirection of the arrow and reinsert the PowerDisk holder at the same time. To do this, the arrows in thePowerDisk holder and in the viewingwindow must point towards eachother. The holder must lie flat. The AutoDos lid must close tigh...
Page 93 - Cleaning the spray arms
Cleaning and care 93 Cleaning the spray arms Particles of food can get stuck in thespray arm nozzles and bearings. Thespray arms should therefore beinspected regularly (approx. every 2–4 months). Never run a wash programmewithout using the spray arms. Damage due to soiling entering the circulation...
Page 94 - Removing the top spray arm; Push the upper spray arm upwards; Removing the middle spray arm; above) and remove the spray arm; Removing the lower spray arm; Remove the lower basket.
Cleaning and care 94 Removing the top spray arm 2 1 Push the upper spray arm upwards to engage the inner ratchet. Thenunscrew the spray arm by rotating thescrew thread anti-clockwise (view from below). Removing the middle spray arm 2 1 Rotate the screw thread of the middlespray arm clockwi...
Page 96 - Inserting the lower spray arm; Damage due to soiling entering
Cleaning and care 96 Inserting the lower spray arm Refit the lower spray arm and ensurethat the filter combination lies flat inthe base of the wash cabinet. Rotate the screw thread of the lowerspray arm clockwise (view fromabove) until the arrow in the viewingwindow points to the lock symbol ...
Page 97 - Cleaning the filters
Cleaning and care 97 Checking the filters in the washcabinet The filter combination in the base of thewash cabinet retains coarse soiling fromthe suds solution. This prevents soilinggetting into the circulation system andre-entering the wash cabinet throughthe spray arms. Damage due to soiling ent...
Page 99 - Cleaning the water inlet filter; Never
Cleaning and care 99 Cleaning the water inlet filter A filter is incorporated in the screwthread to protect the water inlet valve. Ifthe filter is soiled, insufficient waterflows into the wash cabinet. Risk of electric shock from mains voltage.The plastic housing of the waterconnection contains an...
Page 100 - Cleaning the drain pump
Cleaning and care 100 Cleaning the drain pump If water remains in the wash cabinetafter the end of the programme, thewater has not been pumped away. Thedrain pump may be blocked by foreignobjects. These foreign objects are easyto remove. Disconnect the dishwasher from themains. To do this, turn of...
Page 101 - Risk of injury from glass splinters.
Cleaning and care 101 The drain pump (see arrow) isunderneath the cover. Risk of injury from glass splinters. It is especially difficult to see glasssplinters in the drain pump.Take care when cleaning the drainpump. Carefully remove all foreign objectsfrom the drain pump. Check the drainpump imp...
Page 102 - Problem solving guide; Technical problems; Problem
Problem solving guide 102 Many malfunctions and faults that can occur in daily operation can be easilyremedied. You can save time and money in many cases, as you do not need to callthe Miele Customer Service Department.Information to help you rectify faults yourself can be found at www.miele.com/ser...
Page 103 - Fault messages; Door release
Problem solving guide 103 Problem Cause and remedy After the programme hasstarted, the optical in-operation indicator lightis not visible. The reflector panel was not correctly fitted. Re-fit the reflector panel correctly (see installationsheet). Fault messages Problem Cause and remedy The optical...
Page 104 - Water inlet fault; The stopcock is closed.
Problem solving guide 104 Problem Cause and remedy Door opening fault. Switch the appliance off andback on again. Read the op-erating instruction manualfor further details. The door does not open automatically. There may be a technical fault. Open the door manually (see “Before using for thefi...
Page 105 - Water drainage fault
Problem solving guide 105 Problem Cause and remedy Insufficient water intake. Open the stopcock fully.Refer to operating instruc-tions if necessary Before rectifying the problem: Switch the dishwasher off. The water inlet is restricted. Open the stopcock fully and start the programmeagain. ...
Page 106 - Fault in the AutoDos (automatic dispensing); play
Problem solving guide 106 Fault in the AutoDos (automatic dispensing) Problem Cause and remedy The following messagewill appear on the dis-play: PowerDisk inserted? The AutoDos function is activated. There is no PowerDisk or an empty PowerDisk has been inserted. Insert a filled PowerDisk and confi...
Page 107 - function is
Problem solving guide 107 Problem Cause and remedy The in-operation indic-ator light is flashingquickly. At the end of the pro-gramme, the alarm tonemight sound and the dis-play shows the followingmessage: Fault F601: Technical fault. Switch the applianceoff and back on again. Readthe operating ...
Page 108 - Spray arm fault; General problems with the dishwasher
Problem solving guide 108 Spray arm fault Problem Cause and remedy During the programmeand at the end of theprogramme, the displayshows the followingmessage: Check spray arms The dishwasher doesnot switch off at the endof the programme. The crockery may not beclean because no deter-gent was dispense...
Page 109 - Noises
Problem solving guide 109 Problem Cause and remedy The detergent compart-ment lid cannot beclosed. Residual detergent is blocking the catch. Remove the residual detergent. At the end of a pro-gramme there is a film ofmoisture on the inside ofthe door and possibly onthe interior cabinetwalls. This ...
Page 110 - Wash items are insecure in the wash cabinet.
Problem solving guide 110 Problem Cause and remedy Rattling noise in thewash cabinet Wash items are insecure in the wash cabinet. Carefully open the door and rearrange the washitems so that they sit securely. There is a foreign object (e.g. glass shard) in the drainpump. Remove the foreign objec...
Page 111 - Unsatisfactory washing result; The crockery was not loaded correctly.
Problem solving guide 111 Unsatisfactory washing result Problem Cause and remedy The crockery is notclean. The crockery was not loaded correctly. See notes in the “Loading the dishwasher ” forexamples on how to load crockery and cutlery. The programme was not powerful enough. Select a more power...
Page 113 - Unsuitable combination detergents were used.
Problem solving guide 113 Problem Cause and remedy Fill the salt reservoir (see “Before using for the firsttime – Dishwasher salt”). The salt reservoir cap has not been screwed oncorrectly. Replace the cap, making sure that it screws back oncorrectly. Unsuitable combination detergents were used....
Page 114 - The affected items are not corrosion-resistant.; programme without load items in the
Problem solving guide 114 Problem Cause and remedy There are rust stains oncutlery. The affected items are not corrosion-resistant. No remedy.Purchase cutlery that is dishwasher-proof. A programme was not run after dishwasher salt wasadded. Traces of salt have got into the normal washcycle. Imme...
Page 115 - Contact in the event of a fault
Service 115 Information to help you rectify faultsyourself and about Miele spare partscan be found at www.miele.com/service. Contact in the event of a fault In the event of any faults which youcannot remedy yourself, please contactyour Miele dealer or the MieleCustomer Service Department. You can bo...
Page 116 - EPREL database; Warranty; “Comparison
Service 116 EPREL database From 1 March 2021, information onenergy labelling and ecodesignrequirements will be available in theEuropean Product Database (EPREL).You can find the product database atthe following link https://eprel.ec.europa.eu/. You will be asked toenter the model identifier.The mode...
Page 117 - Optional accessories; PowerDisk
Optional accessories 117 Dishwasher detergent, rinse aid andcleaning and care products are availablefor this dishwasher, as are optionalaccessories. All the products have been designed forMiele appliances.These and many other products can beordered from the Miele webshop, theMiele Customer Service D...
Page 118 - Appliance care; Dishwasher cleaner; Descaling agent
Optional accessories 118 Appliance care Miele cleaning and care productsprovide optimum care for your Mieledishwasher. Dishwasher cleaner - For use with the Maintenance programme without detergent dispensing - Cleans the dishwasher effectively and thoroughly - Removes grease, bacteria, and associat...
Page 119 - Installation; The Miele Waterproof system; Health risk due to wash water.
Installation *INSTALLATION* 119 The Miele Waterproof system Provided that your dishwasher has beeninstalled correctly, the Miele Waterproofsystem will protect you from waterdamage throughout its lifetime. Water inlet Health risk due to wash water. Water in the dishwasher is notdrinking water.Do no...
Page 121 - Water drainage; Venting the water drain; Open the dishwasher door fully.
Installation *INSTALLATION* 121 Water drainage The dishwasher ’s drainage system isfitted with a non-return valve, whichprevents dirty water from flowing backinto the appliance via the drain hose.The dishwasher is supplied withapprox. 1.5 m of flexible drain hose withan internal diameter of 22 mm.Th...
Page 122 - Electrical connection; Risk of fire from overheating.
Installation *INSTALLATION* 122 Electrical connection The dishwasher is “connector-ready” asstandard for connection to an earthedsocket.The socket must be easily accessibleafter the dishwasher has been installed.If that is not possible, ensure that asuitable means of disconnection isprovided on the ...
Page 123 - Technical data; Dishwasher model
Technical data 123 Technical data Dishwasher model Normal XXL Height 80.5 cm(adjustable by+6.5 cm) 84.5 cm(adjustable by+6.5 cm) Height of building-in niche Min. 80.5 cm(+6.5 cm) Min. 84.5 cm(+6.5 cm) Width 59.8 cm 59.8 cm Width of building-in niche 60 cm 60 cm Depth 55 cm 55 cm Weight Max. 47 kg Ma...
Page 124 - EU Conformity declaration
Technical data 124 Dishwasher model Normal XXL Off mode Maximum 0.50 W* Standby mode Maximum 0.50 W* Delay start Maximum 4.00 W* Networked standby Maximum 2.00 W* Frequency range of the WiFimodule 2.4000–2.4835 GHz Maximum transmission powerof the WiFi module < 100 mW * see product data sheet for...
Page 125 - This; Statement of Compliance; confirms this Miele product fully complies with the; Paul Wright
Technical data 125 This Statement of Compliance confirms this Miele product fully complies with the Product Security and Telecommunications Infrastructure (Security Requirementsfor Relevant Connectable Products) Regulations 2023. 1) Household Appliance – 2) Manufactured by: Miele & Cie KG, Carl ...
Page 127 - United Kingdom
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TWTel: 0330 160 6600, Internet: www.miele.co.uk, E-mail: [email protected] Australia Miele Australia Pty. Ltd.ACN 005 635 398ABN 96 005 635 398Level 4, 141 Camberwell RoadHawthorn East, VIC 3123Tel: 1300 464 353E-mail: [em...