Miele G7859 - Manual

Warning and safety instructions This machine conforms to currentsafety requirements. Inappropriateuse can however lead to personalinjury and damage to property. Read the operating instructionscarefully before starting to use thismachine. This way you will avoidthe risk of accidents and damage tothe ...

Caring for the environment Disposal of the packing material The transport and protective packinghas been selected from materialswhich are environmentally friendly fordisposal and can normally be recycled. Rather than just throwing these materialsaway, please ensure they are offered forrecycling. Dis...

Before using for the first time Before using for the first time pleasepay special attention to the follow-ing points: Detailed information on these pointscan be found in the relevant section ofthe Operating Instructions. Setting the water softener. The water softener unit must be set todeal with the...

Opening and closing the door Electric door lock The machine is equipped with an elec-tric door lock. The door can only be opened when: the machine is connected electrically the main switch I-0 is on. To open the door a Press the door button in fully and atthe same time pull open the door. Do not tou...

Water softener To avoid the build-up of calcium de-posits on items being cleaned and inthe machine the water needs to be soft-ened. To ensure a steady supply of soft waterthe water softener unit must always be: 1. correctly set (programmed) and 2. the salt reservoir must be filled. (If the water har...

Table of settings °d mg/l °f Setting 123456789 101112131415161718 19 *) 2021222324252627282930313233343536373839404142434445 2040507090 110130140160180200220230250270290310320340360380400410430450470490500520540560580590610630650670680700720740760770790810 24579 1113141618202223252729313234363840414...

Setting the water softener Switch the machine off. Turn the programme selector to f “STOP”. Press 4 and 6 at the same time, hold them in and whilst doing soswitch on the machine with the I-0main switch. The actual programme status “P...”appears in the display.The p / 6 indicator light illuminates. P...

Filling the salt reservoir Please only use specialised reactiva-tion salt, if possible coarse grained re-activation salt, with granules of approxi-mately 1- 4 mm. Under no circumstancesmust other salts be used, e.g. table salt,or gritting salt. These could containcomponents which are insoluble inwat...

Salt indicator When the salt reservoir is empty the k indicator light c comes on. The reser- voir should be refilled with dishwashersalt for reactivation. The reactivation programme runs auto-matically during a programme.The indicator light k b on the pro- gramme sequence display lights upduring thi...

Loading the machine Loading the machine Preparation Empty all containers before loadinginto the machine. Ensure that no acid or solventresidues, especially hydrochloricacid or chlorides access the washcabinet. Notes Load items so that water will comeinto contact with all surfaces. This ensures that ...

Adjusting the upper basket The upper basket can be adjustedabove and below the middle positionby 2.5 cm. It is set in the middle posi-tion on delivery. Depending on the position of the upperbasket plates of the following diametercan be accommodated in the baskets: Example: Upper basket O 881 Upper b...

Adding rinse aid Rinse aid is necessary to ensure thatwater does not cling and leave markson utensils during the drying phase.Rinse aid is poured into the storagereservoir and the amount set is dis-pensed automatically in the final rinse. The rinse aid reservoir holds approx.125 ml. Inadvertently fi...

Setting the dosage The dosage adjuster (see arrow) in theopening has settings adjustable from1 to 6 (1-6 ml). It is set to “3” (3 ml) atthe factory as the recommended dose. If there are flecks on utensils afterdrying use a higher setting. If clouding or smearing occurs onutensils after drying use a ...

Adding cleaning agent Only use cleaning agents formu-lated for specialist machines. Donot use detergents formulated fordomestic dishwashers. Powder cleaning agent is dispensedvia the dispenser for powder cleaningagents in the door or liquid cleaningagent via the DOS module (availableas an optional e...

Note As a chargeable optional extra this ma-chine can also be fitted with a “dispen-ser pump for liquid cleaning agent”(DOS module G 60). This is connectedexternally. See “Programming special functions”for information on venting the dispens-ing system and setting the dosage. See separate instruction...

G 7859 Warning and Safety instructions To the person responsible for this machine: Make this pull-out with the Warning and Safety instructions available to anyoperators of the machine. Place it near the machine, where it can be seen andnot removed. Ensure that operators know and understand these War...

Warning and Safety instructions Repair work may only be carriedout by an authorised Miele service technician or other suitably qualifiedand competent person. Repairs by un-qualified persons could be dangerous. Personnel operating the machineshould be trained regularly. Child- ren and untrained perso...

Ensure that solutions or steam con-taining acid salts do not come into contact with the steel outer casing ofthe machine, to avoid any corrosiondamage. Please follow the advice on installa-tion in these instructions and in the separate Installation Instructions. In countries where there are areaswhi...

Programme selection Choose your programme according tothe type of utensil being cleaned andthe degree of soiling. The different programmes and theiruses are described overleaf in the Programme chart . Programme selection 27

Switching the machine on and off Switching on Close the door. Open the stopcocks (if turned off) . Press the I-0 button. When the programme selector is at the f “STOP” position a point lights up in the display field. Starting the programme Turn the programme selector clock-wise or anti-clockwise to ...

Changing a programme Provided the “Start” button has not yetbeen pressed, a wrongly selected pro-gramme may be changed as describedbelow, (if it has been pressed see “Can-celling a programme”): Turn the programme selector to therequired function. Select additional function 3 (DRYING) again if requir...

Cancelling a programme Once a programme is running it shouldonly be cancelled in extreme cases,e.g. when articles in the machine rattleor bump against each other and haveto be rearranged. Turn the programme selector to the f position (the programme is cancelled afterapprox. 2 secs.). Open the door a...

Programming special functions In the event of a service call at a laterdate, any changes made to the fac-tory setting should be documentedhere.Make a note of any changes made inthe “Value set: ” box. 1. Setting the cold water inlet from:“Nominal water intake” to “Nominalwater intake + 1 l”. The amou...

4. Venting and setting the dosage on“DOS module G 60 or C 60” (specialversion) Set the dosage selector on the DOSmodule to the “10” position (on DOSmodule C 60 only). Turn the programme selector to the f “STOP” position. Switch off the machine. Press 4 and 6 at the same time, hold them in and whilst...

Turn the programme selector backto the programme which needs to bechanged. The actual value appearsin the display after °C . Press 4 or hold it in, until the re- quired value appears in the display. “Final rinse” temperature holdingtime: Turn the programme selector to the f “STOP” position (the prog...

Cleaning and care Cleaning the filters in thewash cabinet The machine must not be used with-out all the filters in place. The filter combination in the base of thewash cabinet should be inspectedregularly and cleaned if necessary.Caution: Watch out for glass splinters whichcould cause injury. Cleani...

Cleaning the spray arms Waste particles can lodge in the sprayarm jets.The spray arms should be inspectedand cleaned regularly (approx. every 6 months). Use a sharp pointed object to pushparticles into the spray arm jets andrinse well under running water. Remove the spray arms as follows: Unscrew th...

Cleaning the filters in the waterinlet For the protection of the inlet valve, filters are incorporated in the screwconnection of the water inlet hose. The filters must be cleaned when dirty,otherwise insufficient water flows intothe wash cabinet. The plastic housing of the water con-nection contains...

Correcting minor faults With the aid of the following explanatorynotes, minor faults can be corrected with-out contacting the Miele Service Dept. Any work on the electrical componentsof the machine should only be carriedout by a suitably qualified and compe-tent person in accordance with localand na...

Water in the wash cabinet is notheated; the programme sequencelasts too long This machine has a resettable thermalcutont which will switch off the heatersin the case of overheating. This couldbe caused, for example, if large articlescover the heating elements or if the fil-ters in the wash cabinet a...

Installation Please refer to the installation diagram supplied with the machine. Furniture and fittings installed near themachine must be of a commercialstandard able to withstand the effectsof steam and condensed water. The machine must be installed correctly and levelled.Any uneveness in the floor...

Electrical connection All electrical connection work must becarried out by a qualified electrician incompliance with local and nationalregulations. For extra safety it is advisable to in-stall a residual current device (RCD)with a trip current of 30 mA. Technical data is available on thedata plate o...

Plumbing Connection to the water inlet Water in the machine must not beused as drinking water. The machine must be connected tothe water supply in accordance withlocal and national regulations. The machine is constructed to com-ply with Australian regulations, andmay be connected to a suitable sup-p...

Drainage The drainage system is fitted with anon-return valve which prevents dirtywater from flowing back into the machine. The machine should preferably beconnected to a separate drainagesystem on-site.If no separate drainage system isavailable, contact the Miele ServiceDepartment.The on-site drain...

Technical data Height: 85 (82) cm Width: 60 cm Depth: 60 cm Voltage: see data plate Rated load: see data plate Fuse rating: see data plate Connection cable: approx. 1.8 m Water pressure (flow pressure): 0.5 - 10 bar (50 - 1000 kPa) Cold or hot water connection: up to max. 70 °C Drainage length: max....