Page 2 - Introduction; Pulsar EX; Pulsar EX
Page 2 - 51031998EN/AA Introduction Thank you for selecting an MGE UPS SYSTEMS product to protect your electrical equipment. The Pulsar EX treme range has been designed with the utmost care. We recommend that you take the time to read this manual to take full advantage of the many features of your U...
Page 3 - Safety; Safety of persons; Safety rules; Product safety; Special precautions
51031998EN/AA - Page 3 Safety Safety of persons Safety rules When the batteries are connected to the UPS, the outlets may be energised even if the UPS is disconnected from the ACinput source. Dangerous voltage levels are present within the UPS. It should be opened exclusively by qualified serviceper...
Page 4 - Foreword; Using this document; Pictograms
Page 4 - 51031998EN/AA Foreword Using this document Important instructions that must always be followed. Information, advice, help. Visual indication. Action. Audio indication. In the illustrations on the following pages, the symbols below are used: LED off. LED on. LED flashing. Information may be ...
Page 5 - Contents; Presentation; Installation; Connection to the RS 232 or USB communications port; Operation; Operation on battery power
51031998EN/AA - Page 5 Contents 1. Presentation 1.1 Pulsar EX treme range ................................................................................................................. 7 Tower model .....................................................................................................
Page 6 - Personalisation; Maintenance
Page 6 - 51031998EN/AA Contents 3.4 Personalisation (optional) ........................................................................................................... 22 Function ........................................................................................................................
Page 7 - range; Tower model
51031998EN/AA - Page 7 1. Presentation 1.1 Pulsar EX treme range Tower model Rack model EX1000 Rack Dimensions in mm (H x W x D) 235.5 x 145 x 505 Weight in kg 9.5 Dimensions in mm (H x W x D) 88 (2U) x 482.6 x 493 Weight in kg 12.5
Page 9 - Rack model
51031998EN/AA - Page 9 1. Presentation Rack model slot for communications-card option. RS232 communications port. USB communications port. four outlets for direct connection ofprotected equipment. input circuit breaker. socket for connection to AC-powersource. 1 2 3 4 6 7 8 10 9 11 connector for bat...
Page 10 - Alarms
Page 10 - 51031998EN/AA 100% 80% 50% 20% test % % 1 2 bypass 1.3 Control panel Alarms UPS overload. electronics fault. battery fault. hold down to display percent load: - lamp test or buzzer OFF.- forced transfer to bypass and backby pressing button 3 times in less than5 seconds. status of programma...
Page 11 - Unpacking and checks
51031998EN/AA - Page 11 2. Installation 2.1 Unpacking and checks two cords for connection of the protected equipment. RS 232 communications cable. USB communications cable. "UPS Driver" diskette for UPS personalisation. "Solution Pac" CD ROM. documentation. ␣ box for battery connecti...
Page 13 - Installation of the rack version; Rack mounting diagram with rails.
51031998EN/AA - Page 13 2.2 Installation of the rack version 2. Installation Rack mounting diagram with rails. The rails and the necessary mounting hardware are supplied by MGE UPS SYSTEMS. 1 2 3 3 3 3 4 EX1000 Rack
Page 14 - Connection to the RS 232 or USB communications port
Page 14 - 51031998EN/AA 2. Installation 2.3 Connection to the RS 232 or USB communications port (optional) 1 - Connect the RS 232 25 or USB 26 communications cable to the serial port orthe USB port on the computer. 2 - Connect the other end of thecommunications cable 25 or 26 to the RS 232 2 or USB ...
Page 15 - Installation of the communications-card option
51031998EN/AA - Page 15 RS232 USB 1 2 2.4 Installation of the communications-card option It is not necessary to shut down the UPS toinstall the communications card: 1 - Remove the slot 1 cover secured by two screws. 2 - Insert the card in the slot. 3 - Secure the card with the two screws. Tower mode...
Page 16 - Battery connection; Warning
Page 16 - 51031998EN/AA 2. Installation 2.5 Battery connection Warning The batteries should be connected only by qualified electrical installation specialists.The work involved in connecting the batteries must be carried out in accordance with all applicable rules and regulations,respecting all safe...
Page 19 - The installation is now configured.; UPS connection and settings
51031998EN/AA - Page 19 2. Installation Connecting the UPS to the AC-input source 1 - Remove the power cord supplying theequipment.Check cord characteristics (> 250 V, 10 A,see the technical sheet).2 - Connect the cord to the AC-power socket ␣ ␣ 7 on the UPS, then to the AC-power wall outlet. Set...
Page 20 - All connected equipment is energised.; Bargraph indications; LEDs 12 to 15 provide three different indications:
Page 20 - 51031998EN/AA 3. Operation 3.1 Start-up 100% 80% 50% 20% test % % 1 2 bypass The protected equipment connected to the UPS can be energised, whether AC input power is available or not. 12 13 14 23 Caution: the AC input power source must be present when energising forthe first time.Press the...
Page 21 - Operation on battery power; Transfer to battery power; The equipment connected to the UPS is supplied by the battery.; Threshold for the low-battery warning; End of backup time; The equipment is no longer supplied with power.
51031998EN/AA - Page 21 3. Operation 3.3 Operation on battery power (following failure of AC input power) 1 2 bypass 1 2 bypass test % 1 2 bypass 22 Transfer to battery power The AC-power source is outside tolerances, LED 23 is ON, the buzzer beeps three times. The equipment connected to the UPS is ...
Page 22 - Function
Page 22 - 51031998EN/AA 3. Operation 3.4 Personalisation (optional) Function Personalisable function Automatic start Cold start (battery power) Forced shutdown Sleep mode UPS ON / OFF via software Default setting Enabled Enabled Enabled Disabled Enabled Personalisation parameters can be set and modi...
Page 25 - Troubleshooting requiring MGE UPS SYSTEMS after-sales support; Indication; Signification; Correction
51031998EN/AA - Page 25 Troubleshooting requiring MGE UPS SYSTEMS after-sales support Indication LED 13 flashes and the buzzer soundscontinuously. Signification UPS electronics have detected a UPS fault.Depending on the UPS personalisation parameters(see section 3.4), there are two possibilities: ◗ ...
Page 26 - This product has been designed to respect the environment:; UPS recycling at the end of service life:
Page 26 - 51031998EN/AA 5. Environment This product has been designed to respect the environment: It does not contain CFCs or HCFCs. UPS recycling at the end of service life: MGE UPS SYSTEMS undertakes to recycle, by certified companies and in compliance with all applicable regulations, allUPS produ...
Page 27 - Technical characteristics; Operating conditions; Input voltage and frequency
51031998EN/AA - Page 27 6. Appendices 6.1 Technical characteristics Operating conditions Relative humidity: 20 to 90 % without condensation.Temperature: 0 to 40 ° C. Simplified diagram Input voltage and frequency 160 V to 276 V +/- 5 % (at rated power) 50 Hz or 60 Hz +/- 5 % Output voltage and frequ...
