Mazda 2008 Tribute HEV - Manual

Drive your new vehicle at least 500 miles (800 km) before towing atrailer. For more detailed information about towing a trailer, refer to Trailer towing in the Tires, Wheels and Loading chapter. Do not add friction modifier compounds or special break-in oils sincethese additives may prevent piston r...

Stopping: The gas engine may shut off to conserve fuel as you come to a stop. Restarting the vehicle is not required. Simply step on theaccelerator when you are ready to drive. Transmission Operation: Due to the technologically advanced, electronically controlled Continuously Variable Transaxle (eCV...

Driving to optimize fuel economy Your fuel economy should improve throughout your hybrid’s break-inperiod. As with any vehicle, fuel economy can be significantly impactedby your driving habits and accessory usage. For best results, keep inmind these tips: Tire Inflation: Keep tires properly inflated...

Frequently asked questions Question Answer What is the pumping sound I hearwhen I unlock or enter the vehicle,and the venting sound a fewminutes after shutting off myvehicle? This is the hydraulic portion ofyour regenerative braking systempressurizing and depressurizing.You may also hear it occasion...

Question Answer Can you charge the battery with aplug into an A/C outlet? There are no provisions forcharging the high voltage batteryfrom a power supply external tothe vehicle. What is the purpose of the ECONbutton? ECON mode may provideimproved fuel economy bypreventing the gasoline enginefrom run...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. WARNING: Please read the section Airbag supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructionscould result in ...

To access this information, special equipment must be directly connectedto the recording modules. Mazda Motor Corporation and Mazda Canadado not access event data recorder information without obtaining consent,unless pursuant to court order or where required by law enforcement,other government autho...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Manual Protecting theEnvironment Fasten Seat Belt Airbag - Front Airbag - Side Passenger Airbag Off Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Parking B...

Vehicle Symbol Glossary Rear WindowDefrost/Demist Power Windows Power Window Lockout Personal Alarm SystemFeature Engine Oil Engine Coolant Engine CoolantTemperature Do Not Open When Hot Battery Avoid Smoking, Flames,or Sparks Battery Acid Explosive Gas Fan Warning Power Steering Fluid Maintain Corr...

Multi-function lever (pg. 58) Instrument cluster (pg. 20) Hazard flasher control (pg. 202) Headlamp control (pg. 47) Parking brake release (pg. 189) Speed controls* (pg. 69) Hood release (pg. 249) Steering wheel controls* (pg. 72) * if equipped 2008 Tribute Hybrid (thv) Owners Guide (post-2002-fmt)U...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a safety hazard or a vehiclecondition that may become serious enough to cause extensive repairs. Awarning light may illuminate when a problem exists with one of yourvehicle’s functions. Many lights will illuminate when you start yo...

WARNING: Under engine misfire conditions, excessive exhausttemperatures could damage the catalytic converter, the fuelsystem, interior floor coverings or other vehicle components,possibly causing a fire. Check fuel cap: Illuminates when the fuel cap may not be properlyinstalled. Continued driving wi...

Airbag readiness: If this light fails to illuminate when the ignition isturned to RUN, continues to flash orremains on, have the systemserviced immediately by your authorized dealer. A chime will also soundwhen a malfunction in the supplemental restraint system has beendetected. Seat belt: Reminds y...

Engine oil pressure: Illuminates when the oil pressure falls below thenormal range, refer to Engine oil in the Maintenance and Specifications chapter. Engine or motor electroniccoolant temperature: Illuminates when the coolant temperatureexceeds the threshold. When the light is flashing or remains o...

Low fuel: Illuminates when the fuel level in the fuel tank is at or nearempty (refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is engaged. Turnsoff when the speed control systemis disengaged. Anti-theft system: Flashes when the SecuriLock™ Passive Anti-theftSy...

Transmission not in park chime: Sounds when the PRNDL is not in P (Park) position, the driver’s door is ajar and the ignition is in the RUNposition. HEV Engine off Reminder Chime: Sounds for 10 seconds when the PRNDL is in the P (Park) position and the Driver’s door is ajar (open)while ignition is i...

AUDIO SYSTEMS AM/FM/single CD/in-dash CD6/MP3 satellite compatible soundsystem Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches, radio and moon roof (if equipped)may be used for up to ten minutes after the ignition is turned off or untileither fr...

For a CD6 system, press EJECT and select the desired CD slot by pressing the corresponding memory preset #. The display will readEJECTING #. When the system has ejected the CD, the display willread REMOVE CD #. Remove the CD. If you do not remove the CDthe system will reload the disc. To auto eject ...

stations without losing your original manually set preset stations forAM/FM1/FM2. To activate the autoset feature, toggle AUTOSET to ON,and either wait five seconds for the search to initiate or press OK toimmediately initiate the search. (If you press another control withinthose five seconds, the s...

In MP3 mode, press FOLD and then press / to access the previous/next folder. In satellite radio mode (early availability — if equipped), use to select from various satellite radio categories. To change categories insatellite radio mode, press CAT/FOLD. The active category will appear inthe display. ...

For a CDX6 system, the system will shuffle between all loaded discs. The disc # will appear in the top left hand corner of the display. 16. SCAN: In radio mode, press for a brief sampling of all strongradio stations. In CD/MP3 mode, press for a brief sampling of all tracks on the current disc or fol...

will prompt you to load discs for the remaining available slots. Insertthe discs, one at a time, label side up, when prompted. Once loaded,the disc in preset #1 will begin to play. 19. CD slot: For a single CDsystem, insert a CD/MP3, label side up. For a CD6 system, press LOAD and select a CD slot u...

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors:...

CD units are designed to play commercially pressed 4.75 in(12 cm) audio compact discs only. Due to technicalincompatibility, certain recordable and re-recordable compactdiscs may not function correctly when used in Mazda CD players. Do not use any irregular shapedCDs or discs with a scratchprotectio...

• Antenna obstructions: For optimal reception performance, keep theantenna clear of snow and ice build-up and keep luggage and othermaterial as far away from the antenna as possible. • Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage...

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly. NO TEXT Category information not available. Category information not available at this time on this channel. The sy...

DUAL AUTOMATIC TEMPERATURE CONTROL 1. AUTO/Driver temperature: Press to engage full automatic operation. The system will automatically determine fan speed, airflowdistribution, A/C on or off, and outside or recirculated air, to heat orcool the vehicle to reach the desired temperature. Turn toincreas...

4. Defrost/Floor: Distributes air through the windshield defroster vents, demister vents, floor vents and rear seat floor vents. Thesystem will automatically provide outside air to reduce windowfogging. On days where the outside temperature is approximatelyfreezing or higher, the engine will run con...

REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel andworks to clear the rear window of fog and thin ice. The ignition must be in the 3 (RUN) position to operate the rear windowdefroster. Press R to turn the rear window defroster on. An indicator light on the ...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the h...

High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. Daytime running lamps (DRL) (if equipped) Turns the lowbeam headlamps on with a reduced output. To activate: • the i...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle duringheadlamp and parklamp operation. Move the control to the full uprightposition, past detent, to turn on theinterior lamps. Rotate to full down position (pastdetent) to prevent inte...

3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover the left-hand headlamp with an opaquecloth. 4. On the wall or screen you will observe a light pattern with adistinct horizontal edge of highintensity light towards the right.If this edge is not at thehorizont...

Cargo and dome lamp Rear cargo lamp equipped with anON/OFF/DOOR control will lightwhen: • the doors are closed and thecontrol is in the ON position. • the control is in the DOORposition and any door is open. When the control is in the OFF position, it will not illuminate when youopen the doors. Inte...

Function Number of bulbs Trade number Backup lamp 2 921 Foglamp (front) 2 9145 Center High-mountstop lamp 5 W5WL Rear license platelamp 2 168 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your authorized dealer Replacing the interior bulbs ...

5. Disconnect the electrical connector from the bulb. WARNING: Children andHalogen Bulbs: Playing with ahalogen bulb is dangerous.Serious injuries could becaused by dropping a halogenbulb or breaking in some otherway. Always keep halogen bulbsout of the reach of children. 6. Connect the electrical c...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: INT 2 — Normal speed operation ofrear wiper. INT 1 — Intermittent operation ofrear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold a...

WARNING: Adjusting the steering wheel while the vehicle ismoving is dangerous. Moving it can very easily cause the driverto abruptly turn to the left or right. This can lead to loss ofcontrol or an accident. Never adjust the steering wheel whilethe vehicle is moving. CENTER CONSOLE Your vehicle is e...

Indicator light Code Green light is On — Power point is ready to supply power Green light is Off — Power point power supply is off. Ignition is not inRUN position Green light is blinking — Power point is in fault mode POWER WINDOWS WARNING: Do not leave children unattended in the vehicle anddo not l...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controls(except for the driver’s) press theright side of the control. Press theleft side to restore the windowcontrols. Accessory delay With accessory delay, the window switches, moon ro...

EXTERIOR MIRRORS Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror androtate the controlcounterclockwise to adjust theleft mirror. 2. Move the control in the direction you wish to tilt themirror. 3. Return to the center position to lock mirror...

CRUISE CONTROL/SPEED CONTROL (IF EQUIPPED) With cruise control/speed control set, you can maintain a set speedwithout keeping your foot on the accelerator pedal. WARNING: Using cruise control in the following conditionscould cause you to lose control of the vehicle: • Heavy or unsteady traffic • Sli...

STEERING WHEEL CONTROLS (IF EQUIPPED) WARNING: Driving while distracted can result in loss ofvehicle control, accident and injury. Mazda stronglyrecommends that drivers use extreme caution when using anydevice that may take their focus off the road. The driversprimary responsibility is the safe oper...

If you open and close the moon roof repeatedly, the moon roof motormay overheat and shut down for 45 seconds while the motor cools. MESSAGE CENTER (IF EQUIPPED) With the ignition in the RUNposition, the message center,located on your instrument cluster,displays important vehicleinformation through a...

Language 1. Select this function from the SETUP menu for the currentlanguage to be displayed. 2. Waiting 4 seconds or pressing the RESET control cycles themessage center through each of the language choices. Selectable languages are English, Spanish, or French. 3. Press and hold the RESET control fo...

Warnings Status Stop safely now Warning returns after 10 minutes ifcondition still exists High engine temperature High motor temperature Park brake engaged XXX miles (km) to empty fuellevel low Liftgate/Glass ajar Warning returns after the ignition keyis turned from OFF to RUN. Service brake system ...

Understanding Your Tire Pressure Monitoring System in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, have the system inspected by your authorized dealer XX% OIL LIFE CHANGE SOON/OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 10% or less....

CARGO AREA FEATURES Cargo shade (if equipped) If your vehicle has a cargo shade, you can use it to cover items in thecargo area of your vehicle. To install the shade: • Insert the ends of the cargoshade into the mounting featureslocated behind the rear seat onthe rear trim panels. To operate the sha...

LUGGAGE RACK Your vehicle is equipped with a roofrack. The maximum load for theroof rack is 100 lbs (44 kg), evenlydistributed on the cross-bars. If it isnot possible to evenly distribute theload, position it in the center or asfar forward on the cross-bars aspossible. Do not use the vehicle’s doorh...

2. Slide the cross-bar to the end of the rail. 3. Use a long, flat object to depress the tongue in theendcaps on both sides of thecross-bar. 4. Slide the cross-bar assembly off the end of the rail. To reinstall the cross-bar assembly (if equipped) to the roof rackside rails: 1. Ensure that both cros...

KEYS Your vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The IKT functions as both aprogrammed ignition key thatoperates all the locks and starts thevehicle, and a remote keyless entrytransmitter. Your IKTs are programmed to your vehicle; using a non-programmed keywill not permit...

POWER DOOR LOCKS • Press the control to unlock all doors. • Press the control to lock all doors. Door key unlocking/locking Unlocking the doors Turn the key in the door cylinder to unlock the driver’s door only. Allother doors will remain locked. Locking the doors Turn the key in the door cylinder t...

2. Press and release again within three seconds to unlock the passenger doors, the liftgate and liftgate glass. The battery saver feature will turn off the interior lamps 10 minutes afterthe ignition is turned to the 1 (OFF/LOCK) position. One step door unlocking If the one step door unlocking featu...

Replacing lost Integrated Keyhead Transmitters (IKTs) If you would like to have your Integrated Keyhead Transmittersreprogrammed because you lost one, or would like to buy additionalIKTs, you can either reprogram them yourself, or take all IKTs to your authorized dealer for reprogramming. How to rep...

• Tail lamps The lamps will automatically turn off: • if the ignition switch is turned to the 3 (RUN) position, or • the IKT (lock) control is pressed, or • after 25 seconds of illumination. Note: On some vehicles, the perimeter lamps illuminated entry feature will not activate in daylight condition...

8. Turn the ignition to the 1 (LOCK) position to exit the procedure. Note: The horn will chirp once to confirm the procedure is complete. SECURILOCK™ PASSIVE ANTI-THEFT SYSTEM SecuriLock™ passive anti-theft system is an engine immobilizationsystem. This system is designed to help prevent the engine ...

If a problem occurs with the SecuriLock™ system, the indicator will flashrapidly or glow steadily when the ignition is in the 3 (RUN) position. Ifthis occurs, the vehicle will not start and should be taken to anauthorized dealer for service. Automatic arming The vehicle is armed immediately after sw...

8. Turn the ignition from the 1 (LOCK) position to the 3 (RUN) position. Keep the ignition in the 3 (RUN) position for at least sixseconds. 9. Remove the newly programmed coded key from the ignition. If the key has been successfully programmed it will start the vehicle’sengine and will operate the r...

Push side control and push down onhead restraint to lower it. Adjusting the front manual seat (if equipped) Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. 2008 Tribute Hybrid (thv) Owners Guide (post-2002-fmt)USA (fus) Seating and Safety Restraints 98

Adjusting the front power seat (if equipped) WARNING: Never adjust the driver’s seat or seatback when thevehicle is moving. You could move out of position to control thevehicle. Then a serious accident could occur. Sudden braking ora collision could cause serious injury. Adjust the seat only whenthe...

REAR SEATS Head restraints The purpose of these head restraints is to help limit head motion in theevent of a rear collision. To properly adjust your head restraints, lift thehead restraint so that it is located directly behind your head or as closeto that position as possible. The head restraints c...

WARNING: Remove the headrestraint stored under thefront set and return it to theoriginal position on theseatback. Failure to do socould result in personal injury. 3. Unsnap the seat belt webbing from the quarter trim panel. To remove the rear cushion 1. Lift the yellow tab to release the hinges. 2. ...

technology, parents are STRONGLY encouraged to always properly restrain children in the rear seat. The sensor also turns off the passengerfront airbag and seat-mounted side airbag (if equipped) when thepassenger seat is empty to prevent unnecessary replacement of airbag(s)after a collision. When the...

seat belt pretensioners, front seat belt buckle sensors, driver seatposition sensor, and front passenger sensing system. In addition, theRCM also monitors the restraints warning light in the instrument cluster.A difficulty with the system is indicated by one or more of the following. • The warning l...

WARNING: In a rollover crash, an unbelted person issignificantly more likely to die or be seriously injured than aperson wearing a seat belt. WARNING: Each seating position in your vehicle has a specificseat belt assembly which is made up of one buckle and onetongue that are designed to be used as a...

2. To unfasten, push the release button and remove the tonguefrom the buckle. Energy Management Feature • This vehicle has a seat belt system with an energy managementfeature at the front outboard seating positions to help further reducethe risk of injury in the event of a head-on collision. • The f...

WARNING: The driver and front passenger seat belt system(including retractors, buckles and height adjusters) must bereplaced if the vehicle is involved in a collision that results indeployment of front airbags, seat-mounted side airbags andSafety Canopy™, and seat belt pretensioners. WARNING: Failur...

WARNING: Failure to inspect and if necessary replace the seatbelt assembly under the above conditions could result in severepersonal injuries in the event of a collision. For proper care of soiled seat belts, refer to Interior in the Cleaning chapter. Seat belt warning light and indicator chime The ...

The following are reasons most often given for not wearing seat belts(All statistics based on U.S. data): Reasons given... Consider... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day. The more we drive, the more we are exposed to ⬙ rare ⬙ events, even for good drivers. 1 in 4 of us will be...

WARNING: Do not sit on top of a buckled seat belt or insert alatchplate into the buckle to avoid the Belt-Minder 威 chime. To do so may adversely affect the performance of the vehicle’s airbag system One time disable If at any time the driver/front passenger quickly buckles then unbucklesthe seat bel...

WARNING: If the airbag has deployed, the airbag will notfunction again and must be replaced immediately. If the airbagis not replaced, the unrepaired area will increase the risk ofinjury in a collision. Front passenger sensing system The front passenger sensing system is designed to meet the regulat...

Note : The indicator lamp will illuminate for a short period of time when the ignition is turned to the ON position to confirm it is functional. When the front passenger seat is not occupied (empty seat) or in theevent that the front passenger frontal airbag is enabled (may inflate), theindicator la...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

A difficulty with the system is indicated by one or more of the following: • The readiness light (same light as for front airbag system) will eitherflash or stay lit. • The readiness light will not illuminate immediately after ignition isturned on. • A series of five beep sounds will be heard. The t...

Children and seat belts If the child is the proper size, restrain the child in a safety seat. Childrenwho are too large for child safety seats (as specified by your child safetyseat manufacturer) should always wear seat belts. Follow all the important safety restraint and airbag precautions thatappl...

• Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? Typ...

Children and booster seats vary widely in size and shape. Choose abooster that keeps the lap belt low and snug across the hips, never upacross the stomach, and lets you adjust the shoulder belt to cross thechest and rest snugly near the center of the shoulder. The drawingsbelow compare the ideal fit...

WARNING: Never use pillows, books, or towels to boost achild. They can slide around and increase the likelihood ofinjury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully foll...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Every day before you drive, check your tires. If one looks lower than theothers, use a tire gauge to check pressure of all tires and adjust ifrequired. At least once a month and before long trips, inspect each tire and checkthe tire pressure with a tire gauge (including spare, if equipped). Inflatea...

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressure, etc.) the tires experience throughout theirlives.In general, tires should be replaced after 6 years regardless oftread wear. However, heat caused b...

Important: Remember to replace the valve stems when the road tires are replaced on your vehicle. Note: The use of a different tire can effect the fuel economy of your vehicle. The tire pressure monitoring sensors mounted in the wheels (originallyinstalled on your vehicle) are not designed to be used...

Tire and wheel alignment A bad jolt from hitting a curb or pothole can cause the front end of yourvehicle to become misaligned or cause damage to your tires. If yourvehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel ali...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Mazda dealership to check for and correct any...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

Compliance Certification Label, which is located on the B-Pillar orthe edge of the driver’s door, for the correct tire pressure for yourvehicle. 12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested unde...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

following two conditions: (1) This device may not cause harmfulinterference, and (2) This device must accept any interference received,including interference that may cause undesired operation. WARNING: The Tire Pressure Monitoring System is NOT asubstitute for manually checking tire pressure. The t...

Low Tire PressureWarning Light Possible cause Customer Action Required Solid Warning Light Tire(s)under-inflated 1. Check your tire pressure toensure tires are properlyinflated; refer to Inflating your tires in this chapter. 2. After inflating your tires tothe manufacturer’srecommended inflationpres...

Low Tire PressureWarning Light Possible cause Customer Action Required Flashing WarningLight Spare tire in use Your temporary spare tire is in use. Repair the damaged roadwheel and re-mount it on thevehicle to restore systemfunctionality. For a descriptionof how the system functionsunder these condi...

any tire is under-inflated, carefully drive the vehicle to the nearestlocation where air can be added to the tires. Inflate all the tires to therecommended inflation pressure. SNOW TIRES AND CHAINS WARNING: Snow tires must be the same size and grade as thetires you currently have on your vehicle. Th...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your authorized dealer plus any aftermarketequipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

WARNING: Do not use replacement tires with lower loadcarrying capacities than the original tires because they maylower the vehicle’s GVWR and GAWR limitations. Replacementtires with a higher limit than the original tires do not increasethe GVWR and GAWR limitations. WARNING: Exceeding any vehicle we...

• A final example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You and one of your friends decide to pick up cementfrom the local home improvement store to finish that patio you havebeen planning for the past 2 years. Measuring the inside of the vehiclewith the rear seat fol...

4WD GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum GCWR - lb. (kg) Trailer Weight Range - lb. (kg) Maximum frontal area of trailer - ft 2 (m 2 ) 2.3L 4980 (2259) 1000 (454) 24 (2.2) Notes: For high altitude operation, reduce GCW by 2% per 1000 ft. (300 meters) elevation. For defi...

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric, manual, automatic or surge-type brakes, if compatible with thevehicle, are safe if installed properly and adjusted to the manufacturer’sspecifi...

• Do not exceed the GCWR rating or transmission damage may occur. Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance information for more information. Trailer towing tips • Practice turning, st...

Exceeding these limits may allow water to enter vehicle components: • causing internal damage to the components. • affecting driveability, emissions and reliability. Replace the rear axle lubricant any time the axle has been submerged inwater. Rear axle lubricant quantities are not to be checked or ...

STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such asthe radio to operate while thevehicle is not running. 3. RUN, all electrical circuits operational and warning lightswill illuminate. This is thepositio...

vehicle still does not start, it may require refueling, jump starting,resetting of the fuel pump/high voltage shut-off switches or service. Forinformation on jump starting the vehicle and resetting the fuelpump/high voltage shut-off switches, refer to the Jump starting your vehicle (low voltage [und...

Association (CSA). Use only an extension cord that can be usedoutdoors, in cold temperatures, and is clearly marked ⬙ Suitable for Use with Outdoor Appliances. ⬙ Never use an indoor extension cord outdoors; it could result in an electric shock or fire hazard. • Use a 16 gauge outdoor extension cord,...

Make sure system is unplugged and properly stowed before driving thevehicle. While not in use, make sure the protective cover seals theprongs of the engine block heater cord plug. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, ...

Using ABS When hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since this will reduce theeffectiveness of the ABS and will increase your vehicle’s stoppingdistance. The ABS will be activated immediately, allowing you to retainsteering control during ha...

to interact with the anti-lock brake system (ABS). Regenerative brakingis disabled when the ABS is activated or the battery is fully charged. Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAK...

WARNING: In a rollover crash, an unbelted person issignificantly more likely to die than a person wearing a seatbelt. Utility vehicles and trucks have larger tires and increased groundclearance, giving the vehicle a higher center of gravity than a passengercar. WARNING: Vehicles with a higher center...

N (Neutral) With the gearshift lever in N (Neutral), the vehicle is free to roll; holdthe brake pedal down while in this position. Because of the uniquenature of the hybrid vehicle, the engine will not start in the N (Neutral)position. The vehicle does not charge the high voltage battery in the N (N...

power distribution between the front and rear wheels. It combinestransparent all-surface operation with highly capable four-wheel drive. The 4WD system is always active and requires no driver input. It iscapable of handling all road conditions, including street and highwaydriving as well as off-road...

• It often may be less risky to strike small objects, such as highwayreflectors, with minor damage to your vehicle rather than attempt asudden return to the pavement which could cause the vehicle to slidesideways out of control or roll over. Remember, your safety and thesafety of others should be yo...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, the vehicle may stall. Once thro...

Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally upor down a hill or steep incline, you should always try to drive straight upor straight down. Avoid driving crosswise or turning on steep slopes or hills . A danger lies in losing traction, sli...

DRIVING THROUGH WATER If driving through deep or standingwater is unavoidable, proceed veryslowly especially when the depth isnot known. Never drive throughwater that is higher than the bottomof the wheel rims (for cars) or thebottom of the hubs (for trucks). When driving through water, traction or ...

HAZARD FLASHER CONTROL The hazard flasher is located on thesteering column, just behind thesteering wheel. The hazard flasherswill operate when the ignition is inany position or if the key is not inthe ignition. Push in the flasher control and allfront and rear direction signals willflash. Press the...

If you see or smell fuel, do not reset the fuel pump shut-off or try tostart your vehicle; you could injure yourself or others. Have all thepassengers get out of the vehicle and call the local fire department or atowing service. FUSES AND RELAYS Fuses If electrical components in thevehicle are not w...

COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 70A — — Tan — Brown 80A — — Natural Black Black Passenger compartment fuse panel The fuse panel is located on theright-hand side of the centerconsole, by the instrument panel.Remove the panel cover to acc...

WARNING: To reduce risk of electrical shock, always replacethe cover to the power distribution box before reconnecting thelow voltage (underhood) battery or refilling fluid reservoirs. If the low voltage (underhood) battery has been disconnected andreconnected, refer to the Low voltage (underhood) b...

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 31C — Heater pump relay 31D — Coolant pump relay 31E — Not used 31F — Not used 32 — A/C clutch diode 33 — PCM diode 34 — Not used 35 5A* RUN/START 36 — Not used 37 — Not used * Mini fuse ** Cartridge fuse CHANGING A FLAT TIRE If ...

WARNING: The use of tire sealants may damage your TirePressure Monitoring System and should not be used. WARNING: Refer to Tire Pressure Monitoring System (TPMS) in the Tire, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomesdamaged, it will no longer f...

Use of one of the dissimilar spare tires listed above at any one wheellocation can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • Winter weather driving capability • Wet weather driving capability 3. Fu...

To remove jack from vehicle: 1. Release the thumbscrew on the bracket. 2. Release the retention clip on the upper part of the jackbracket. 3. Dislodge the jack from the bracket and carefully guide jackdown and out through trimopening, upper end out first. Remove the lug wrench from thejack in order ...

If equipped with a tether, perform the following additional steps: 4. Lift the spare tire on end to access tether attachment (1). 5. Use the lug wrench to remove the lug nut from the spare tiretether. 6. If not replacing the spare or flat tire to the underbody storagearea, raise winch up into theins...

1. Place tire on end with valve stem facing rearward, awayfrom vehicle. 2. Place tether into bolt holes in wheel and attach lug nut usinglug wrench. 3. Lay the tire on the ground with the valve stem facing down. If your vehicle is equipped with aluminum wheels, remove the wheelornament. 4. Slide the...

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 500 miles (800 km)after any wheel disturbance (tire rotation, changing a flat tire, wheelremoval, etc.). Bolt size Wheel lug nut torque* lb.ft. N • m M12 x 1.5 100 135 * Torque specifications are for nut and bolt t...

JUMP STARTING(LOW VOLTAGE [UNDERHOOD] BATTERY ONLY) Your vehicle has two separate jump starting procedures; the followingprocedure is for the low voltage (underhood) battery only. Refer to Jump starting the high voltage battery in this chapter for information on jump starting the high voltage batter...

5. Turn the heater fan on in both vehicles to protect from any electrical surges. Turn all other accessories off. Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to desi...

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’s engine, away from the battery andthe carburetor/fuel injection system. Do not use fuel lines, engine rocke...

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the...

JUMP STARTING THE HIGH VOLTAGE BATTERY Your vehicle has two separate jump starting procedures; the followingprocedure is for the cargo area high voltage battery only. Refer to the Jump starting your vehicle (Low voltage [underhood] battery only) section in this chapter for information on jump starti...

When the button is pressed, the indicator light on the button willilluminate. After eight minutes has passed, the indicator light will flashrapidly for two minutes. Turn the ignition to RUN. You may now attemptto start the engine. If you attempt to start the engine before the eight minutes passes, t...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

CUSTOMER ASSISTANCE (U.S.A. MAINLAND AND HAWAII) Your complete and permanent satisfaction is our business. We are here toserve you. All Authorized Mazda Dealers have the knowledge and thetools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvementre...

Whatever way you contact us, please help us to serve you moreefficiently and effectively by providing the following information: 1. Your name, address, and telephone number 2. Year and model of vehicle 3. Vehicle Identification Number (17 digits, noted on your registration or title or located on the...

Provide the Department with the following information: 1. Your name, address, and telephone number 2. Year and model of vehicle 3. Vehicle Identification Number (VIN). Refer to Vehicle identification label in the Maintenance and Specifications chapter of this manual for the location of the VIN. 4. P...

CAMVAP uses the services of Provincial Administrators to assistconsumers in scheduling and preparing for their arbitration hearings.However, before you can proceed with CAMVAP you must follow yourMazda dispute resolution process as outlined previously. CAMVAP is fully implemented in all provinces an...

IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor vehicle to conform to thevehicle’s applicable express warranty after a reasonable number ofattempts, the manufacturer shall be required to either replac...

• Federal Emission Control Warranty– Emission Defect Warranty– Emission Performance Warranty • California Emission Control Warranty (if applicable) • Replacement Parts and Accessories Limited Warranty • Tire Warranty NOTE: Detailed warranty information is provided with your Mazda portfolio. Outside ...

WARNING: Add-On Electrical and Electronic Equipment:Incorrectly choosing or installing improper add-on equipment orchoosing an improper installer could be dangerous. Essentialsystems could be damaged, causing engine stalling, air-bag(SRS) activation, ABS inactivation, or a fire in the vehicle. Bever...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and spot paintedsurfaces. • Never wash a vehicle that is “hot to the touch” or dur...

PAINT CHIPS Your dealer has touch-up paint to match your vehicle’s color. Touch-uppaint can be used to repair minor scratches to painted surfaces. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always r...

• Cover the highlighted areas to prevent water damage when cleaningthe engine. Note: As with all transmissions, be especially careful as water entry into the vents can damage internal parts. • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. P...

• The wiper blades can be cleaned with isopropyl (rubbing) alcohol or awindshield washer concentrate. This washer fluid concentrate containsa special solution in addition to alcohol which helps to remove the hotwax deposited on the wiper blade and windshield from automated carwash facilities. Be sur...

SERVICE RECOMMENDATIONS To help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Information Booklet ...

1. High voltage connector shield 2. Service Disconnect 3. High voltage battery case Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpec...

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located underthe bottom of the instrumentpanel. 2. At the front of the vehicle, lift up on the auxiliary latch handlelocated in the center betweenthe hood and the grille. 3. Lift the hood open and secure it with the prop rod. 2008 ...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Motor/Electronics (M/E) coolant reservoir 3. Engine oil filler cap 4. Brake fluid reservoir 5. Power distribution box 6. Low Voltage (underhood) battery 7. Engine air filter assembly 8. Engine oil dipstick...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Mazda specifications. Do not use anyspecial washer fluid such as windshield water repellent type fluid or bugwash. They may cause ...

CHANGING THE WIPER BLADES 1. Pull the wiper blade and arm away from the glass. Turn theblade at a right angle to thearm. 2. Squeeze the locking tabs to release the blade from the armand pull the blade away fromthe arm to remove it. 3. Attach the new blade to the arm and snap it into place. Replace w...

To replace the wiper blade: 1. Grab the wiper arm just below the blade attachment and pull itas far away from the glass aspossible. Do not use excessiveforce because it can break thewiper arm at the heel. Hold itthere until the next step. 2. Grab the wiper blade with your other hand and use your fin...

5. Locate and carefully remove the engine oil level dipstick. 6. Wipe the dipstick clean. Insert the dipstick fully, then remove it again. • If the oil level is within the MIN and MAX marks or the lower andupper holes, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN ...

2. If the engine oil level is not within the normal range, add only certified engine oil of the recommended viscosity. Remove the engineoil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the FULL mark on the ...

Change your engine oil and filter according to the appropriate schedulelisted in scheduled maintenance information. When changing the oil filter on the 2.3L engine you must also replacethe filter cap O-ring. The oil filter drain plug O-ring must also bereplaced whenever the oil filter drain plug is ...

6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more torelearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is ...

Checking engine coolant The concentration and level ofengine coolant should be checked atthe intervals listed in scheduled maintenance information . The coolant concentration should bemaintained at 50/50 coolant anddistilled water, which equates to afreeze point of -34°F (-36°C).Coolant concentratio...

Checking motor/electronics (M/E) coolant The M/E coolant reservoir is locatedbehind the engine coolant reservoir.Refer to the following enginecoolant sections for all information,instructions and warnings related tocooling systems. The two systemsuse the same coolant and operatesimilarly, with the M...

If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not u...

Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage). Recycled engine coolant Mazda Motor Corporation does NOT recommend the use of recycledengine coolant in vehicles originally equipped with Mazda Premium Gol...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

WARNING: Gasoline may contain benzene, which is acancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforerefueling your vehicle. • Always turn off the vehicle beforerefueling. • Automotive fuels can be harmfulo...

WARNING: The flow of fuel through a fuel pump nozzle canproduce static electricity, which can cause a fire if fuel ispumped into an ungrounded fuel container. Refueling WARNING: Fuel vapor burns violently and a fuel fire can causesevere injuries. To help avoid injuries to you and others: • Read and ...

If the check fuel cap lamp or a “check fuel cap” message come on, the fuel filler cap may not be properly installed. The lamp or messagecan come on after several driving events after you’ve refueled yourvehicle. At the next opportunity, safely pull off of the road, remove the fuel fillercap, align t...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” thatare sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes kno...

If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling to allow the fuel system to pump the fuel from the tank tothe engine. On restarting, cranking time will take a few seconds longerthan normal. • Normally, adding 1 gallon (3.8L) of fuel is en...

2. Each time you fill the tank, record the amount of fuel added (in gallons or liters). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading. 5. Follow one of the simple ...

• Minimize temperature extremes when the vehicle is parked, forexample by storing in a garage to avoid extreme cold in winter andextreme sun loads in summer. The high voltage battery operates moreefficiently in moderate temperatures. • Combine errands. Your vehicle is more fuel efficient when the en...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

Note: The brake system on this vehicle can only be bled at a authorized dealer. TRANSMISSION FLUID Checking electronically controlled continuously variabletransmission (eCVT) Refer to your scheduled maintenance information chapter for scheduled intervals for fluid checks and changes. Your transaxle ...

7. The fluid level should be within 1/4 inch (6 mm) of the plugthreads. 8. Replace the check plug. Adjusting eCVT fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is indicated in the Maintenance product specifications and capacities section in this chap...

Changing the air filter element 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halves of the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to remove any dirt or debris an...

Changing the high voltage battery air filter element 1. Remove access panel located in the rear cargo area on thedriver’s side trim panel toexpose the filter cover. 2. Push the tabs (located on each side of filter cover) while pullinggently to remove filter cover. 3. Install new filter and filter co...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross Vehicle Weight Rating (GVWR) /Restraint System 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence n...

CELL PHONES Use of cell phones and other devices by driver: WARNING: Use of any electrical devices such as cell phones,computers, portable radios, vehicle navigation or other devicesby the driver while the vehicle is moving is dangerous. Dialing anumber on a cell phone while driving also ties-up the...

GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for yourvehicle. Carefully following this schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay also help to increase the value of ...

Genuine Mazda Parts and Service When planning your maintenance services, consider your Mazdadealership for all your vehicle’s needs. Get the most from your service and maintenance visits There are a lot of reasons why visiting your Mazda Dealership for allyour service needs is a great way to help ke...

WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW? Owner Checks and Services Refer to Mileage Intervals for Additional Checks and Services Certain basic maintenance checks and inspections should be performedby the owner or a service technician at the intervals indicated. Serviceinformation and supporting...

Multi-point Inspection In order to keep your vehicle running right, it is important that you havethe systems on your vehicle checked regularly. This can help identify anypotential issue before there are any problems. Mazda Motor Corporationsuggests the following multi-point inspection to be performe...

SPECIAL OPERATING CONDITIONS Towing a trailer or using a camper or car-top carrier Every 5,000 miles, 6 months or 200 hours of engine operation (whichever comes first) Change engine oil and replace filter Every 5,000 miles Inspect tires and rotate Extensive Idling and/or Low Speed Driving for Long D...

Special Operating Conditions Log D EALER V ALIDATION : RO#: P&A C ODE : D ATE : M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE : M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE : M ILEAGE : D EALER V ALIDATION : RO#: P&A C ODE : D ATE : M ILEAGE : D EALER V ALIDATION...

MAZDA PREMIUM GOLD ENGINE COOLANT CHANGE RECORD Current mileage goes here => Add 50,000 miles to the current miles + 50,000 Next change due at this mileage => Or Today’s date goes here => Add 3 years + 00 / 00 / 03 Date of next change => whichever comes first Dealer Stamp P & A CODER...

A Accessory delay ..........................65 Air cleaner filter ...............278–280 Air conditioning automatic temperaturecontrol system ..........................42 Airbag supplemental restraintsystem ........................120, 129, 131 and child safety seats ............122description ........

doors ..........................................87 Lubricant specifications ...........281 Lug nuts ....................................221 Luggage rack ...............................84 M Manual transmission fluid capacities ........................281lubricant specifications ..........281 Message ...

V Vehicle Identification Number(VIN) ..........................................284 Vehicle loading ..........................170 Ventilating your vehicle ...........185 W Warning lights (see Lights) .......20 Washer fluid ..............................251 Water, Driving through .............201 Wind...