Maytag MDB4949SHZ - Manual

5 Other Parts Needed (not provided): 3 / 8 " Compression x 3 / 4 " Hose Fitting with rubber seal and 90° elbow (required to properly connect household water line to the dishwasher) (Whirlpool Part Number W10685193) Household Wiring (Metallic) Strain Relief to fi t 7 / 8 " (22   mm) hole ...

6 For Direct Wire For Power Cord Cabinet Grommet For 1 1 / 2 " (38 mm) hole in cabinet. (Whirlpool Part   Number   302797) NOTE: Required for metal cabinets Power Cord Kit Kit typically includes power cord, metallic strain relief,   grommet, and twist-on wire connectors. (Whirlpool Part Number 4...

7 Product and Cabinet Opening Dimensions 23 7 / 8 " (606 mm) 30" (762 mm) " 3 7 / 16 7 / 16 " (87 mm - 11 mm) 33 1 / 2 " (851 mm) min. with wheels removed 24 1 / 2 " (622 mm) B 3 / 4 " (19 mm) A 30" (762 mm) 3 3 / 4 " (95 mm) 21" (533 mm) C 24" (610 mm) E ...

8 ELECTRICAL REQUIREMENTS Be sure that the electrical connection and wire size are adequate   and in conformance with the National Electrical Code, ANSI/NFPA 70 - latest edition, and all local codes and   ordinances. A copy of the above code standards can be obtained from: National Fire Protection A...

9 PREPARE CABINET OPENING – NEW UTILITIES NOTE: Refer to the “Product and Cabinet Opening Dimensions” section for the correct hole placement and dimensions of the shaded area. Drill a 1 1 / 2 " (38 mm) drain hose hole in the side or rear of cabinet, depending on location of drain hose routing an...

10 Built-up fl oors: If the kitchen fl oor is higher than the cabinet opening’s fl oor - for example, the kitchen fl oor tile does not extend into the cabinet opening - add shims, as needed, in the area shown to bring the dishwasher up to 34" (864 mm) below the countertop. NOTE: Shims must be se...

11 PREPARE DISHWASHER Helpful Tip: Place cardboard under dishwasher until installed in   cabinet opening to avoid damaging fl oor covering. Using 2 or more people, grasp sides of dishwasher door frame,   and place the dishwasher on its back. Do not use the door panel as a worktable without fi rst co...

12 Measure height of cabinet opening from underside of countertop to fl oor where dishwasher will be installed. Be sure to measure the lowest point on the underside of the countertop and the highest point on the fl oor. Adjust both front leveling legs to the same height. Put the rear wheels in the c...

13 Copper tubing only: Put the tubing into the 90° elbow fi tting as far as it will go. (The copper tubing bends and kinks easily.) Slide the nut and ferrule forward and start the nut onto the elbow   threads. NOTE: To avoid vibration during operation, route the water supply line so that it does not...

14 NOTE: Route drain hose out the rear of the dishwasher. POWER CORD CONNECTION NOTE: If removing a previous dishwasher with a power cord, you will need to transfer the power cord to the new dishwasher. Use a 1 / 4 " nut driver or 1 / 4 " hex head socket wrench to remove the screw that holds...

17 Countertop Attachment: Remove the brackets from the package, and insert into the open   slots on the left- and right-hand top of the dishwasher collar   as shown. Go to Step 41. Using pliers, bend/twist tab to lock the brackets in place. Side Attachment: Break off the end of the bracket along the...

18 If door closes too quickly or falls, open and adjust spring tension. To adjust the door spring tension, remove the white plastic rope end attached to the door hinge. Using a 5 / 16 " nut driver or hex socket, remove the screw from the tensioner. The screw can be put into one of 3 holes (1, 2,...

20 DIRECT WIRE CONNECTION Use a 1 / 4 " nut driver or 1 / 4 " hex head socket wrench to remove the screw that holds the terminal box to the cross brace. Then, tilt the terminal box, free the tab, and lift the terminal box away from the crossbar. Remove the cover by sliding it up and lifting ...

22 Helpful Tip: Remove disposer knockout plug. 1. Using a hammer and screwdriver, knock plug into disposer. 2. Use needle-nose pliers to remove plug. 3. Attach drain hose to disposer inlet with large drain hose clamp (provided). Use pliers to squeeze clamp open and move into position. Option A: Wast...

24 COMPLETE INSTALLATION Check that the power supply wire or cord does not touch dishwasher motor or the lower part of the dishwasher tub. Plug into a grounded 3 prong outlet. NOTE: With the access panel off, start the dishwasher and allow it to complete the shortest wash cycle. After the fi rst 2 m...

25 Metal Panel: Place the panel against dishwasher legs. Using a Phillips screwdriver or 1 / 4 " nut driver, reinstall the   screws through the holes in the access panel. Check that the lower edge of the access panel touches the fl oor. Adjust if necessary. Tighten access panel screws. 65. Reins...

26 ADDITIONAL TIPS Expect longer wash times. Your new dishwasher will average 2-5 hours per load but use nearly 40% less energy than older models. Designed with a low wattage, low energy consumption motor, your dishwasher washes longer to ensure exceptional cleaning. Certain models are equipped with...