Marley 761 - Manual
Marley 761 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – NEW HOME INSTALLATION; IMPORTANT: Be sure nothing obstructs the discharge of the fan.
- Page 4 – BE SURE ALL WIRING COMPLIES WITH LOCAL AND NATIONAL ELECTRICAL
- Page 5 – INSTALLATION IN EXISTING HOMES; Refer to wiring diagrams for wiring and Fig. 6 & 7 for duct work.; knockout from housing.
- Page 7 – nail all four ends of mounting brackets.; REQUIREMENTS AND ADJUSTMENTS FOR HUMIDITY SENSING UNITS ONLY; –Replace the grille and turn the unit on to check its operation.
- Page 8 – ACCESSORIES; MODEL
- Page 9 – LEA Y GUARDE ESTAS INSTRUCCIONES; VENTILADORES MODELOS; DESCRIPCION; INSTRUCCIONES IMPORTANTES DE SEGURIDAD; PARA REDUCIR EL PELIGRO DE INCENDIO,; HERRAMIENTAS
- Page 11 – INSTALACION EN UNA CASA NUEVA; Desconecte el conector macho del conector hembra del motor.
- Page 15 – tando las figuras anteriores.
- Page 16 – ACCESORIOS; MODELO
- Page 17 – LIRE ET CONSERVER CES INSTRUCTIONS; LATEURS; DESCRIPTION; INSTRUCTIONS DE SÉCURITÉ IMPORTANTES; AVERTISSEMENT; N’utilisez pas ce ventilateur avec n’importe quel dispositif de; OUTILS
- Page 19 – NOUVELLE INSTALLATION DOMESTIQUE; électrique et dégagez le trou enfonçable voulu dans le châssis.; IMPORTANT: Vérifiez bien que rien n’obstrue l’évacuation du; Installez le verre rentrant en engageant ses taquets dans les; SCHÉMA 3
- Page 21 – Ouvrez le trou enfonçable voulu dans le châssis.
- Page 23 – ANCIENNE INSTALLATION DOMESTIQUE; Découpez l’ouverture environ 6 mm plus largement que ce marquage.
- Page 24 – ACCESSOIRES; MODÈLE; SPÉCIFICATIONS; CONDUITE
READ AND SAVE THESE INSTRUCTIONS
MODELS 761, 763, 765, 7100, 7130, 7150,
8090 & 8100 FANS
MODELS 768IC, 770IC, 7100L, 7150L, 7100FL, 7150FL,
8090L & 8100L FAN/LIGHTS
MODELS 7100H, 7100FLH, 7150H & 7150FLH
FANS & FAN/LIGHTS with HUMIDITY SENSOR
DESCRIPTION
The FAN and FAN/LIGHT models listed in these instructions
are intended for use in bathrooms. However, they can also be
used in other areas where ventilation is required. These units
are approved for installation in the ceiling above a bathtub or
shower stall only when connected to a U.L. Listed GFCI pro-
tected branch circuit. ALL FAN/LIGHT models are U.L. Listed
Type I.C. (Inherently Protected) for installation in insulated ceil-
ings.
UNPACKING
Unpack carefully. If there are missing components or hidden
damage, immediately contact your distributor or the delivering
carrier concerning discrepancies.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
TO REDUCE RISK OF FIRE, ELECTRICAL SHOCK OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
1.
Do not use this fan with any Solid-State speed control
device.
2.
Use this unit only in the manner intended by the manufa-
cturer. If you have any questions, contact the
manufacturer.
3.
Before servicing or cleaning unit, switch power off at
service panel and lock service panel to prevent power
from being switched on accidentally.
4.
Installation work and electrical wiring must be done by
qualified person(s) in accordance with all applicable
codes and standards, including fire-rated construction.
5.
Sufficient air is needed for proper combustion and
exhausting of gases through the flue (chimney) of fuel
burning equipment to prevent back drafting. Follow the
heating equipment manufacturer’s guideline and safety
standards such as those published by the
National Fire Protection Association (NFPA), and the
American Society for Heating and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
6.
When cutting or drilling into wall or ceiling, do not damage
electrical wiring or other hidden utilities.
7. Ducted fans must always be vented to the outdoors.
8. If this unit is installed over a tub or shower, it must be
marked as appropriate for the application. See product
label.
9. NEVER place a switch where it can be reached from a tub
or shower.
10. CAUTION: For General Ventilation Use Only! Do not
use to exhaust hazardous or explosive materials or vapors.
11. Not for use in kitchens.
TOOLS
Installation of your Marley Engineered Products fan is easy. No
special technical knowledge is needed; only a few ordinary
tools are required:
Screwdriver
Hammer
Saber saw, Keyhole saw, or Jig saw
Electric drill with bit
Wire cutters
Wire stripper
Wire nuts and general electrical supplies
Safety glasses
Ruler and straight edge
All hand tools should be insulated. Power tools should display
the UL Listing Mark.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
NEW HOME INSTALLATION MODELS 761, 763, 765, 768IC, AND 770IC NOTE: Plastic scroll and motor assembly can be removed fromthe metal housing prior to step one if desired. Simply loosen fourmounting screws securing scroll to housing and slide it towardsthe outlet box. Carefully lift and tilt scroll, mot...
FIG. 6 FIG. 7 CAUTION! BE SURE ALL WIRING COMPLIES WITH LOCAL AND NATIONAL ELECTRICAL CODES, AND HOUSING IS PROPERLY GROUNDED. ROOF CAP WALL CAP 4” ROUND DUCT 4” ROUND DUCT ROOF OUTLET BOX RECEPTACLE WIRING DIAGRAMMODELS 768IC, 770IC LIGHT GREEN WHITE WHITE WHITE GREEN BLACK WIRING DIAGRAMMODELS 710...
INSTALLATION IN EXISTING HOMES (MODELS: 761, 763, 765, 768IC & 770IC) 1. Review the section: “New Home Installation” and follow instructions where applicable. 2. Refer to wiring diagrams for wiring and Fig. 6 & 7 for duct work. 3. Determine location of ventilator, remembering that the housin...
