Makita EH7500S - Manual
Makita EH7500S – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – epair
- Page 3 – Note
- Page 4 – Caution
- Page 9 – Plug Cap
- Page 10 – Spark Plug
- Page 11 – Ignition Coil
- Page 12 – clockwise
- Page 13 – Fly Wheel
- Page 14 – DISASSEMBLING
- Page 15 – ASSEMBLING; Spiral spring
- Page 18 – Push
- Page 20 – ON
- Page 21 – TUBING
- Page 22 – and Muffler gasket from Muffler.
PRODUCT
P 1/ 25
EH7500S
Petrol Hedge Trimmer
Model EH7500S is a 22.2cm³ 2-stroke petrol hedge trimmer
with single-sided blade in compliance with all known exhaust
emission regulations, featuring extra light design with further
improvements in noise, vibration and handling compared with
our current models.
Especially, the lightweight design is outstanding.
4.7kg (10.4lbs) dry weight is the world’s lightest among all petrol
hedge trimmers in compliance with any exhaust emission regulation
as of February, 2010.
323 (12-3/4)
Dimensions: mm (")
Width (W)
Height (H)
Length (L)
1,150 (45-1/4)
212 (8-3/8)
T
ECHNICAL INFORMATION
Model No.
Description
C
ONCEPT AND MAIN APPLICATIONS
S
pecification
S
tandard equipment
Note:
The standard equipment for the tool
shown above may vary by country.
O
ptional accessories
Blade cover .................... 1
Socket wrench ................ 1
Hex wrench .................... 1
Chip receiver set
35 (1-3/8)
4,390
22.2
Stroke rate at No load: min.
ˉ
¹ = spm
(stroke pre minute)
0.4 (13.5)
Fuel tank capacity: L (US oz)
Engine
Displacement: cm³
Fuel
2-stroke
Mixed gasoline
Specifications
Model
Type
Blade
Net weight
*2
: kg (lbs)
Max. torque: N.m
Carburetor
0.9 [at 6,000 min.
ˉ
¹]
EH7500S
750 (29-1/2)
2.3 (3/32)
Yes
Diaphragm
Max. cutting capacity: mm (")
728 (25-5/8)
Recoil starter
Starting system
Yes
Primer pump
Rotation limiter
Yes
Clutch
Yes
Max. output power: kW (PS)
0.68 (1.0) [at 7,500 min.
ˉ
¹]
Length: mm (")
Thickness: mm (")
Blade drive mechanism
Type
Tooth spacing: mm (")
Max. branch diameter
*1
: mm (")
Single-sided
with 3 sharpened edges
21.5 (7/8)
4.7 (10.4)
In compliance with main exhaust emission regulations;
CARB Tier 3, EPA Phase 2, EU Stage 2
Connecting rod drive
*1:
Indicates maximum diameter of the branch that can be received
between adjacent two blade teeth. (See the figure on right.)
*2:
Dry weight
Cutting teeth
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
R epair Apply Makita Grease N. No.2 to Spiral spring for recoil starter (approx. 2g) and Gear room (approx. 40g). [1] NECESSARY REPAIRING TOOLS < Note in repair> * Repair the tool always with gloved hand * Blades must be covered by Blade cover * Cool down the engin first before repairing to av...
R epair [3] DISASSEMBLY/ASSEMBLY [3] -1. Engine section Fig. 3 (1) Disconnect Bullet terminal from the Lead wire of Ignition coil. ( Fig. 1 ) (2) Remove Air cleaner cover and disconnect control cable from the swivel of carburetor. Remove Control cable from cable bracket. ( Fig. 2 ) (3) Remove three ...
P 4/ 25 R epair [3] DISASSEMBLY/ASSEMBLY [3] -2. Clutch Section Fig. 5 By using impact driver, Clutch can be loosened without holding Piston by utilizing air pressure in the cylinder. In order to utilize this air pressure resistant, do not remove Spark plug in this step. (1) Separate Engine section ...
