Lux 3M-22 - Manual

Lux 3M-22

Lux 3M-22 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
Page: / 14

Table of Contents:

  • Page 2 – mount the new thermostat in place of the old one.; Good
  • Page 3 – then proceed with the; Caution; Trim
  • Page 4 – D o n o t a l l o w w i r e s t o t o u c h e a c h o t h e r o r p a r t s o n t h e r m o s t a t .; What wires do you have?
  • Page 5 – If you combination of wires is not above you can use the; Find the set-up diagram for your system; or
  • Page 6 – Install AAA Batteries; AAA
  • Page 7 – Check Unit; (If you connected the
  • Page 8 – Power Options; of actual; To change the calibration:; Calibration; Calibrate button
  • Page 9 – WIRE HEAT; NOTE: Wires marked with; Wire Heat; RH; terminal; Please Go To Page 9
  • Page 10 – W Y RH G; W Y RH RC G
  • Page 11 – O Y R G; Wire Heat Pump w/o Aux; O W2 Y RH G
  • Page 12 – W2 W Y Y2 RH RC G; Stage Heat and Cool
  • Page 13 – Wire Reference; Your Wires; SEE NOTE; B and O
  • Page 14 – Printed in China; Wire Reference cont; Jumper Reference; Configuration jumpers allow your
Loading the manual

• Your thermostat is a precise instrument, handle it with care.
• Turn off electricity to the appliance before installing or
servicing thermostat or any part of the system.
• Do not turn electricity back on until work is completed.
• Do not short (jumper) across electric terminals at control on
furnace or air conditioner to test the system. This will damage
the thermostat and void your warranty.
• All wiring must conform to local codes and ordinances.
• This thermostat is designed for use with 24 volt AC and
millivolt systems. The thermostat should be limited to a
maximum of 1.0 amps; higher amperage may cause damage
to the thermostat.

Caution

Install guide 3M-22

ENGLISH

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - mount the new thermostat in place of the old one.; Good

Location Caution Tools To avoid electrical shock and to prevent damage to the furnace, air conditioner, and thermostat, disconnect the power supply before beginning work. This can be done at the circuit breaker, or at the appliance. Replacement installations - mount the new thermostat in place of th...

Page 3 - then proceed with the; Caution; Trim

Remove old unit Prepare wires IMPORTANT : LABEL ALL WIRES BEFORE DISCONNECTING THEM! • Switch electricity to the furnace and air conditioner OFF ; then proceed with the following steps.• Remove cover from old thermostat. Most are snap-on types and simply pull off. Some have locking screws on the sid...

Page 4 - D o n o t a l l o w w i r e s t o t o u c h e a c h o t h e r o r p a r t s o n t h e r m o s t a t .; What wires do you have?

Before you Connect Wires Caution D o n o t a l l o w w i r e s t o t o u c h e a c h o t h e r o r p a r t s o n t h e r m o s t a t . Please follow these guidelines for safe and secure wire connections.• Easy Terminals do not require stripping the wire.• Clip any bare wire from previous installatio...

Other Lux Models

All Lux Other