Lucent Technologies 308/616 - Manual

Page 3 - REPAIR INSTRUCTIONS

INTERFERENCE INFORMATION FCC REGULATIONS PERTAINING TO THIS EQUIPMENT NOTICE Federal Communications Commission (FCC) rules require that you be notified of the following: FCC (Part 15)This equipment generates, uses, and can radiate radio frequency energy and, if not installed andused in accordance wi...

Page 4 - TABLE OF CONTENTS; Customer Installation Instructions 1

TABLE OF CONTENTS Introduction 2 Overview of System 2 Step 1 Plan Your System 3 Step 2 Check Outlet Grounding 3 Step 3 Mount Controller 4 Mount Controller on Wall 4 Test the Incoming Telephone Lines 5 Connect Telephone Lines to Controller 5 Step 4 Wiring Runs 6 Business (4-pair) Wiring 7 Mount Jack ...

Page 5 - Customer Installation Instructions

Introduction This instruction manual will show you how to install your SPIRIT Communications System. Please read the instructions carefully before beginning installation. Overview of System What You Should Find in the Boxes With the Controller: controllerthree 7’ line cords system directory labelcor...

Page 6 - Step 1 Plan Your System; representative and order part number 31304.; INCOMING TELEPHONE LINES; NOTE: Be sure cords do not cross walkways. Do not run cords; Step 2 Check Outlet Grounding; Customer Installation Instructions 3

Step 1 Plan Your System Draw a floor plan of your business, showing the location of the network interface jacks,where your local telephone lines come into the building. You will want to install yourcontroller close to these jacks.Show on the floor plan the location of each telephone in your system. ...

Page 7 - Step 3 Mount Controller; Mount Controller on Wall; labels, and place it on the side of the controller.; MOUNTING TEMPLATE

Step 3 Mount Controller ■ Mount Controller on Wall Choose a location within five feet of the network interface jacks, where the localtelephone company lines enter the building, and near an AC outlet that is not controlledby a switch. Be sure the controller is in a well-ventilated area with a tempera...

Page 8 - Customer Installation Instructions 5

■ Test the Incoming Telephone Lines. TEST: If you have a standard telephone with a modular cord, plug it into each jack of thenetwork interface, or incoming telephone lines. If these jacks do not work you willrequire service by your local telephone company.When the telephone lines were installed, th...

Page 9 - Step 4 Wiring Runs

Step 4 Wiring Runs You may choose to wire your SPIRIT Communications System using 4-pair “business”wiring materials or 2-pair “customer convenience” wiring materials. While the materials are somewhat different, the procedure for labeling the wiring run is the same.Each “run” from the controller to a...

Page 10 - TELEPHONE; Customer Installation Instructions 7

Step 4A Business (4-pair) Wiring You may choose to wire your business with 4-pair “business” wiring to be ready forfuture communications systems. You will need the following materials: ❑ screwdriver (flathead) ❑ scissors ❑ drill and bits appropriate for your walls ❑ You will also need the following ...

Page 11 - Mount Jack Panel Boxes

■ Mount Jack Panel Boxes Mount the jack panel boxes near the controller, creating a “jack field.” You will need one jack panel box for every six telephones in your system. Ideally, the jack field will betwo to six inches below the controller if the controller is wall-mounted.Mounting screws for the ...

Page 12 - Run Cable To All Telephone Locations; Customer Installation Instructions 9

■ Run Cable To All Telephone Locations Select a cable extension kit with the right length of cable (100 or 200 feet) for one cable run. For runs over 200 feet, run a 200-foot cable, terminate it in a modular connectingblock, plug in another cable, and repeat, up to a maximum of 1000 feet. Select a C...

Page 13 - Install Modular Connecting Blocks; Install a modular connecting block at each telephone location; 0 Customer Installation Instructions

■ Install Modular Connecting Blocks Install a modular connecting block at each telephone location Find the modular connecting block from the Cable Extension Kit and the cable installation tool from the Wiring Installation Kit. Choose the location for the connecting block according to the figure. Cut...

Page 14 - Typical cable installation for one telephone location.; Customer Installation Instructions 11

Typical cable installation for one telephone location. Cable clip Identical labels Cable TELEPHONE LOCATION Modular connecting block Finish your installation by routing cables to all other telephone locations and installingmodular connecting blocks for each one. Be sure to label both ends of each ca...

Page 15 - Step 4B Wiring Run, Using Customer Convenience Wiring; Install Plugs; 2 Customer Installation Instructions

Step 4B Wiring Run, Using Customer Convenience Wiring Customer convenience wiring materials are available at your local phone store. Differentsituations require different materials. For instance, if a telephone location is less than 25 feet from the controller, you may choose to buy a 25’ D4BU line ...

Page 16 - Typical Installation Using Customer Convenience Wiring; Customer Installation Instructions 13

Typical Installation Using Customer Convenience Wiring Sample System Directory Label Controller 10 11 12 13 7 0 0 A 4 P L U G T e l e p h o n eL a b e l s 630B Wall Connecting Block Wire Run Greater Than 50’ Telephone Set Modular Cord (D4BU) 2 5 ’ M a x . Wire Run Less Than 50’ Telephone Set Cord (i...

Page 17 - Step 5 Install Telephone Sets; SPIRIT; bottom of the base. Swing the set into position and lock into place.; Label Intercom Extension Number; plastic hook; 4 Customer Installation Instructions

Step 5 Install Telephone Sets SPIRIT telephone sets are available in 6-Button and 24-Button models. The models are installed the same way. SPIRIT telephones are not like regular telephones and will not work ifplugged directly into the Network Interface Jacks. Regular telephones will not work if they...

Page 18 - Testing the Incoming Telephone Company Lines; telephones are being used and that all the receivers are in place.; Controller Test; All telephones in the system must be idle.; Results; there is a defect in the 308 controller.; Customer Installation Instructions 15

Step 6 Connect System To Wiring Runs Connect the controller to the wiring runs. Following the numbers on your wiring run labels, plug one end of a jumper cord into the jack panel box or wire junction (see pages 7 and 14) and the other end of the jumper cord into the appropriate station jack on the c...

Page 19 - Ignore the rest of the lights on the set.; Telephone Test; All of the indicator lights on the set should go ON.; 6 Customer Installation Instructions

3. The left INTERCOM light should be lit if there is a 616 expansion unit installedcorrectly. If there is not an expansion unit installed, and the light does light, then there isa defect in the 308 controller. If a 616 expansion unit is present, check that the connector is properly installed (see th...

Page 20 - Troubleshooting; What To Do If You Have Trouble With Your System:; Optional Accessories; music jack on the controller.; Replacement Parts; Part; Customer Installation Instructions 17

Troubleshooting What To Do If You Have Trouble With Your System: For SPIRIT Communications Systems purchased from AT&T, a customer “hotline” (1-800-628-2888) is available to help you if you have questions about or trouble with your system. If you need assistance from the hotline, please follow t...

Lucent Technologies 308/616 - Manual

Table of Contents:

Summary

Other Lucent Technologies Models