Linear VS-GSWG - Manual

Linear VS-GSWG

Linear VS-GSWG – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
Page: / 34

Table of Contents:

  • Page 2 – Table of Contents; WARNING
  • Page 3 – Pre-installation Information; Always Check the Gate’s Action; Safety Information and Warnings; Regulatory Warnings; THE FOLLOWING FORMATS ARE USED FOR SAFETY NOTES; IMPORTANT INSTALLATION SAFETY INSTRUCTIONS; STEPS BEFORE PROCEEDING
  • Page 4 – Wiring Specifi cations; AC Power Wiring; USE COPPER WIRE ONLY!
  • Page 5 – Mounting Pad Installation; Gate Preparation; Figure 2. Mounting Pad Specifi cations; Figure 1. Side Plate Installation
  • Page 6 – Operator Preparation; Vent Plug Installation; Gate Arm Installation; Gate Arm Assembly; Observe the way the chain threads around the sprockets for; Figure 3. Vent Plug Installation
  • Page 7 – Operator Setup; Controller Access; is not
  • Page 8 – Open and Close Limit Adjustment; REMOVE THE CARDBOARD FILLER; limit switches are the ones closer to the bottom; Limit Nuts Rough Adjustment; Before running the operator, set the limit nuts as follows:; Limit Nuts Fine Adjustment; Figure 9. Setting the Limits; IN; CAUTION
  • Page 9 – Torque Limiter Adjustment; The open and close current sensing may need to be; To adjust the torque limiter in a Model VS-GSWG:; increase the torque
  • Page 10 – Controller Features; Figure 11. Controller Features
  • Page 11 – Indicator Descriptions
  • Page 12 – Terminal Descriptions
  • Page 13 – Operator Accessory Connections; Figure 12. Operator Accessory Connections
  • Page 14 – Basic Controller Programming; The Mid-travel Stop feature is disabled when dual gate
  • Page 15 – Run Alarm and Pre-start Alarm; OPEN; Maximum Close Direction Current Setting; while this function is; CLOSE; MAX CLOSE; RUN ALARM
  • Page 16 – Advanced Controller Programming; Entering Advanced Programming Mode; The factory default sets the; input terminal so successive inputs; SINGLE; input can be set to cause the gate to OPEN; Stagger Mode; This function is used in dual gate installations only.; COMM LINK; Stagger Delay Time; This function is used in dual gate installations only.; The factory
  • Page 17 – Auxiliary Relay Mode; If a button is set for constant pressure, and it is released; Shadow Loop Open Prevention; closing; AUXILIARY; BRAKE
  • Page 18 – Reset Cycle Count; Maintenance Alert Trigger; MAINT ALERT; Mid-travel Stop Position; still fully open; Radio Enable; ANTENNA
  • Page 19 – The Controller can be reset with this function.; ALL PROGRAMMED; , and the factory defaults will be loaded. This
  • Page 20 – Loop Layout Illustration
  • Page 21 – Safety Edge Layout Illustration; ARNING
  • Page 22 – Photoeye Installation Illustration
  • Page 23 – Dual Gate Installations; The shield wire should be connected COMM LINK terminal; • Dual Gate Enable; Optional In-Cabinet Heater; Figure 13. COMM LINK Wiring
  • Page 24 – Gate Operation; Operation Indications; • Stop is displayed as; St; • Full Close is displayed as; FC; • Full Open is displayed as; FO; • Entrapment is displayed as
  • Page 25 – Error Indications; Entrapment; after the gate stops.; Maximum Run Time Exceeded
  • Page 26 – Troubleshooting; fr
  • Page 27 – Preventative Maintenance; General; Bearings; -Month Preventative Maintenance; If the solenoid emits a loud; FCC Notice
  • Page 28 – Model VS-GSWG Exploded View
  • Page 30 – Controller Parts List
  • Page 31 – Variable Speed Drive Programming; Programming the Hitachi Inverter; must have this switch in
  • Page 32 – Gate Arm Assembly Parts List
  • Page 33 – This page left blank intentionally.
  • Page 34 – Gate Operator Installation Checklist; OR
Loading the manual

VS-GSWG

Swing Gate Operator

Installation Guide

USA & Canada (800) 421-1587 & (800) 392-0123

(760) 438-7000 - Toll Free FAX (800) 468-1340

www.linearcorp.com

Operator models contained in this manual

conform to UL325 standard for use in

Class I, II, III, and IV applications

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Table of Contents; WARNING

VS-GSWG Swing Gate Operator Installation Guide - ii - P1250 Revision X6 7-8-2011 Table of Contents Pre-installation Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Before You Begin... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Alway...

Page 3 - Pre-installation Information; Always Check the Gate’s Action; Safety Information and Warnings; Regulatory Warnings; THE FOLLOWING FORMATS ARE USED FOR SAFETY NOTES; IMPORTANT INSTALLATION SAFETY INSTRUCTIONS; STEPS BEFORE PROCEEDING

VS-GSWG Swing Gate Operator Installation Guide - 1 - P1250 Revision X6 7-8-2011 Pre-installation Information Before You Begin... Before unpacking, inspect the carton for exterior damage. If you fi nd damage, advise the delivery carrier of a potential claim. Inspect your package carefully. You can ch...

Page 4 - Wiring Specifi cations; AC Power Wiring; USE COPPER WIRE ONLY!

VS-GSWG Swing Gate Operator Installation Guide - 2 - P1250 Revision X6 7-8-2011 Wiring Specifi cations Refer to the following steps for details on power and accessory wiring for the operator. AC Power Wiring 1. Find the listing on this page corresponding to the model, voltage and horsepower rating o...

Other Linear Models

All Linear Other