Linear AUJ-S - Manual

ITEM # PART# DESCRIPTION QUAN. 1 Operator Power Head 1 2 005031 3 Button St ation 1 3 30 Tooth Sprocket, 1” Bore, 1/4 Key 1 4 20 Tooth Sprocket, 1” Bore, 1/4 key 1 5 105193 Release/Hand Chain Wall Bracket 1 —— AR - As Required ITEM # PART# DESCRIPTION QUAN 6 100413 1/4” Square Key 2 7 006119 5/16-18...

F igure 4, page 8 illustrates several positions suitable for mounting the operator; right hand or left hand, either wall mount or ceiling mount and center mount with direct coupling to the torsion shaft. Direct coupling may also be used in a side mount installation. Operators intended for direct cou...

DIRECT COUPLING MOUNTING F igure 4, page 8 illustrates several positions suitable for mounting the operator including center mount with direct coupling to the torsion shaft. Direct coupling may also be used in a side mount installation. Operators intended for direct coupling require an internal spee...

Figure 4 100719 Right Side Mount Ceiling Mount Left Side Mount Ceiling Mount Center Mount Direct Couple Wall Mount Wall Mount 8 FIGURE 4 - OPERATOR MOUNTING POSITIONS

107173 Figure 5 NOTE: Dimensions for Model AUJ-S are similar to above, Model AUJ-S is not provided with a chain hoist. 9 FIGURE 5 - OPERATOR DIMENSIONS - MODEL AUH-S 7.75

10 FIGURE 6 - OPERATOR DIMENSIONS - MODEL AUJ-S 107173 Figure 6 NOTE: Dimensions for Model AUH-S are similar to above, Model AUH-S is provided with a chain hoist. 15 7.75

4) Depress the limit nut retaining Plate (D) so it disengages from the slots in the limit nuts. Turn the OPEN limit nut (E) on the shaft until it engages the Open Limit Switch (A). You will need to listen for an audible click. Release the retaining plate and be sure that it engages in slots of both ...

RISK OF ENTRAPMENT THAT MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DISCONNECT POWER TO THE OPENER BEFORE AND DURING INSTALLATION OF AN ACCESSORY REVERSING DOOR EDGE OR PHOTOELECTRIC DEVICE. DO NOT RECONNECT POWER TO OPENER UNTIL INSTRUCTED TO DO SO. ENSURE DOORWAY IS CLEAR BEFORE STARTING TESTI...

9. See Figure 9 for connecting the photoelectric device to the operator. See Page 17 for proper setting of the selector switches. These switches must be properly set and an approved photoelectric device or approved door edge device connected to the operator to obtain B2 Mode of Operation, Momentary ...

MOTOR CONTROL BOARD Figure 9 OP E N TB1 STOP CLOSE OPEN CO M CLOS E STO P NO RE V NC R E V PHOT O CO M SIN G L E ILO C K 24 V A C CO M SAFE FINISH PHOTOBEAM 3-WIRE PHOTOBEAM Door Edge and Photoelectric Wiring INSTALLATION INSTRUCTIONS 14 After properly connecting an approved Entrapment Protection De...

15 NOTE: It is now necessary to turn on the power in order to change the Operating Mode (if applicable), program any changes desired to the operator’s other settings, check for proper performance of all the operator’s features to include the brake (if applicable) and clutch (adjusting settings if ne...

Understand all of the operating features of your door control system at the time of its installation. Your installing dealer will demonstrate them for you. NEVER let children operate or play with door controls. Keep the Remote Control (where provided) away from children. Personnel should keep away f...

Changing the Switch Selectable Operation Modes The following modes are selected by setting the on-board dip switches, Figure 20 at right shows where the switches are located on the operator control board. For each Operational Mode, the switches are set to either ON or OFF according to the table at r...

Mid-Stop : Activation stops an opening door; momentary contact of open button at mid stop will restart door to full open position; if door is moving open, constant pressure on open button will bypass mid-stop. Auto Close Timer : N/A TS Operation Open Button : Momentary activation; open override of c...

The solenoid operated brake may require occasional adjustment. Adjustment is necessary if door tends to drift downward after reaching the open limit. Follow the instructions below and use Figure 14 as a guide. (1) Loosen shoe adjusting screw and bottom bracket arm of solenoid. (2) Move tab until dru...

CLUTCH ADJUSTMENT The clutch serves to protect the door, the electric operator and other equipment from undue stress or damage caused by starting forces and/or an obstruction to the door. It should be set no tighter than is necessary to smoothly and consistently move the door throughout its full ran...

Normally, very little maintenance is required. A monthly visual inspection must be made for loose or missing hardware and for excessive slack in the V-Belt and jackshaft chain. The clutch must be tested periodically and adjustments made if necessary (see page 20). The brake is adjusted at the factor...

WIRING DIAGRAM/SCHEMATIC - SINGLE PHASE 23 575 VOLTS, 3 PHASE SINGLE VOLTAGE MOTOR BL/BLK BL/BLK TO REVERSE MOTOR, SWITCH LEADS 1 & 3 L1 4 L2 YELLOW WHITE BLACK ORANGE BLUE RED Wire Nut Connection 3 BLUE (T,J,H) YELLOW BLUE RED BLACK A.O. SMITH SINGLE VOLTAGE - 115 VAC, 1P MOTOR RED (AU) YELLOW ...

WIRING DIAGRAM/SCHEMATIC - THREE PHASE 24 575 VOLTS, 3 PHASE SINGLE VOLTAGE MOTOR BL/BLK BL/BLK TO REVERSE MOTOR, SWITCH LEADS 1 & 3 L1 4 L2 YELLOW WHITE BLACK ORANGE BLUE RED Wire Nut Connection 3 BLUE (T,J,H) YELLOW BLUE RED BLACK A.O. SMITH SINGLE VOLTAGE - 115 VAC, 1P MOTOR RED (AU) YELLOW 3...

PARTS IDENTIFICATION 25 Ref Part# Description Assemblies A 109351 Frame Assembly w/Shafts. AUJ 109358 Frame Assembly w/Shafts, AUH C 110076 Clutch Shaft Assembly, AUJ 110077 Clutch Shaft Assembly w/Hoist, AUH E 109848 Secondary Shaft Assembly, AUJ / H (1/3 HP) 109274 Secondary Shaft Assembly, AUJ / ...

26 SPECIFICATIONS MODEL : AUJ_ _ _ _S HP:_____ VOLTS : _____ PHASE : _____ * UL AND CANADIAN UL LISTED* HIGH STARTING TORQUE, CONTINUOUS DUTY MOTOR* MOTOR OVERLOAD PROTECTION* CLASS 2 (24 VOLT) CONTROL CIRCUIT* SOLENOID BRAKE* SOLID STATE MOTOR CONTROL CIRCUITRY WITH * THREE BUTTON CONTROL: OPEN, CL...