Linear RE-BWC1 - Manual

Copyright © 2007 Linear Corporation

227793 A

RE-BWC1

Black & White

CCTV Camera

Installation Instructions

PRODUCT DESCRIPTION

Linear’s Model RE-BWC1 (P/N ACP00886A) CCTV camera can be installed inside
the RE-1 Entry System. The camera provides a video signal for viewing the area in
front of the entry system
The camera is continuously powered by the RE-1. The camera’s infrared light emitters
illuminate the area directly on front of the entry system for nighttime or low light
operation.
The camera focus has been factory adjusted to a range of three to four feet.
The RE -1

CAMERA

jack is used to connect the camera to the main circuit board with

the single-ended modular cable supplied with the camera. This cable routes power to,
and video from the camera.
The RE-1

VIDEO

jack is for connection to a video cable with a Type “BNC” connector. Up

to 300 feet of 75-ohm RG-59 video cable can be used. Longer cable runs may require the
use of a video amplifi er.

NOTE: If camera is being installed on an existing installation, power must be off
prior to removing circuit board.

1. REMOVE CIRCUIT BOARD

2. MOUNT THE CAMERA

3. CONNECT LIGHTING POWER

4. REPLACE CIRCUIT BOARD

5. CONNECT CAMERA CABLE

6. CONNECT VIDEO CABLE

LINEAR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship
for twenty four (24) months. The Warranty Expiration Date is labeled on the
product. This warranty extends only to wholesale customers who buy direct from
Linear or through Linear’s normal distribution channels. Linear does not warrant
this product to consumers. Consumers should inquire from their selling dealer
as to the nature of the dealer’s warranty, if any.

There are no obligations or

liabilities on the part of Linear LLC for consequential damages arising
out of or in connection with use or performance of this product or other
indirect damages with respect to loss of property, revenue, or profi t, or
cost of removal, installation, or reinstallation.

All implied warranties, including

implied warranties for merchantability and implied warranties for fi tness, are valid
only until Warranty Expiration Date as labeled on the product.

This Linear LLC

Warranty is in lieu of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an
RPA# and other important details.

DI

S

CONNECT THE

S

E

TWO CONNECTOR

S

REMOVE THE

S

E

4

S

CREW

S

REMOVE
CIRCUIT
BOARD

S

ECURE THE CAMERA A

SS

EMBLY

WITH TWO

S

CREW

S

IMPORTANT!

TO PREVENT INTERNAL
INFRARED LIGHT FROM
ENTERING THE CAMERA,
BE SURE THE FOAM GASKET
AROUND THE CAMERA'S
LENS PRESSES FIRMLY AGAINST
THE RE-1'S FACEPLATE

IN

S

ERT WIRING

HARNE

SS

PLUG

INTO THE 2-PIN
LIGHTING
CONNECTOR

PLUG THE CAMERA CABLE
INTO THE CAMERA'

S

JACK

AND THE RE-1'

S

CAMERA JACK

RE-1

CAMERA

JACK

CAMERA
CABLE FROM
CAMERA'

S

JACK

CONNECT THE VIDEO CABLE FOR THE MONITOR
TO THE RE-1'

S

VIDEO OUTPUT CONNECTOR

RECONNECT THE

S

E

TWO CONNECTOR

S

S

ECURE WITH

4

S

CREW

S

REPLACE
CIRCUIT
BOARD

PRINTER’

S

IN

S

TR

UCTION

S

:

INSTR,INSTL,RE-BWC1 - LINEAR P/N:

227793 A - INK:

BLA

CK - MA

TERIAL:

20 LB

. MEAD BOND - SIZE:

8.500”

X 11.000”

- SCALE:

1-1

(760) 438-7000

USA & Canada (800) 421-1587 & (800) 392-0123

Toll Free FAX (800) 468-1340

www.linearcorp.com