Linear J-S - Manual
Linear J-S – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – WARNING; TABLE OF CONTENTS
- Page 3 – The purpose; of this booklet is to provide assembly,; PRODUCT FEATURES
- Page 4 – COMPONENT IDENTIFICATION
- Page 5 – COMPONENT IDENTIFICATION LISTING; TO REDUCE THE RISK OF SEVERE; the door manufacturer’s instruction manual for a; STRONGLY ADVISED FOR ALL; • Locate the control station:; IMPORTANT INSTALLATION INSTRUCTIONS!; READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS!
- Page 6 – Proceed to “Chain Hoist and Floor Disconnect Installation”.; Figure 2; INSTALLATION INSTRUCTIONS
- Page 7 – Figure 3
- Page 8 – Figure 6; FIGURE 4 - OPERATOR MOUNTING POSITIONS
- Page 10 – Figure 8; SETTING THE LIMIT SWITCHES; ) Manually raise the door to a fully open position.
- Page 11 – MUST BE CONNECTED; Observe local electrical codes when wiring the operator.
- Page 12 – CAUTION; Door Edge; Door Edge Installation Illustration; DOOR EDGE and PHOTOELECTRIC INSTALLATION
- Page 13 – Figure 9; Door Edge and Photoelectric Wiring; ENTRAPMENT PROTECTION DEVICES WIRING INSTRUCTIONS
- Page 14 – Before; Single 3 Button Station; Single Button and External Interlock Wiring; TURNING ON THE POWER TO THE OPERATOR; Multiple 3 Button Station; /SINGLE BUTTON STATION / INTERLOCK FIELD WIRING
- Page 15 – FAILURE TO TEST REVERSING; IMPORTANT SAFETY INSTRUCTIONS FOR OWNER; TEST THE DOOR OPENER’S; READ AND FOLLOW ALL INSTRUCTIONS!; OPERATION & ADJUSTMENT INSTRUCTIONS
- Page 16 – Changing the Switch Selectable Operation Modes; page 3 of this manual is attached to the input labeled “Photo”, it; Settable; SETTING THE SWITCH SELECTABLE OPERATING MODES
- Page 17 – TS Operation; SETUP MODES; Setup Modes; Delay on Reverse Setup; Close Limit Delay Setup; temporarily; Setup Mode
- Page 18 – BRAKE ADJUSTMENT; Mid-Stop Limit Setup; Auto Close Timer Setup; Maximum Run Time Setup
- Page 19 – CLUTCH ADJUSTMENT; Before adjustment remove power to the
- Page 21 – TESTING; ALWAYS DISCONNECT POWER TO; on page 17 for the adjustment; MAINTENANCE
- Page 22 – MOTOR WIRING CHART; BALDOR; SINGLE PHASE; SEE; only one
- Page 23 – MOTOR
- Page 24 – NOTES
- Page 25 – PARTS IDENTIFICATION
- Page 26 – SPECIFICATIONS; LINEAR LIMITED WARRANTY
I N S TA L L AT I O N A N D
O W N E R ’ S M A N U A L
As of date of manufacture,
meets all ANSI/UL 325
Safety Requirements for
Ve h i c u l a r d o o r o p e ra to rs
J-S & H-S
J & H SERIES WITH SOLID STATE CONTROL CIRCUITRY
JACKSHAFT COMMERCIAL VEHICULAR DOOR
OPERATORS
R E A D T H I S M A N U A L
C A R E F U L L Y B E F O R E
I N S T A L L A T I O N O R U S E
S A V E T H E S E I N S T R U C T I O N S !
Serial #:
Date Installed:
Your Dealer:
USA & Canada
(800) 421-1587 & (800) 392-0123
(760) 438-7000
Toll Free FAX (800) 468-1340
www.linearcorp.com
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
READ THESE STATEMENTS CAREFULLY AND FOLLOW THE INSTRUCTIONS CLOSELY. The Warning and Caution boxes throughout this manual are there to protect you and your equipment. Pay close attention to these boxes as you follow the manual. WARNING Indicates a MECHANICAL hazard of INJURY OR DEATH. Gives instruct...
The purpose of this booklet is to provide assembly, installation and operation information concerning Model J-S & H-S Commercial Vehicular Garage Door Operators and related Accessory Products. NOTICE IT IS IMPORTANT THAT THIS INSTRUCTION MANUAL BE READ AND UNDERSTOOD COMPLETELY BEFORE INSTALLATI...
Before starting the installation of the operator, the door must be in good working condition and properly counterbalanced. Inspect the door and track for loose or missing hardware. Test the door manually for balance and ease of operation. Lubricate door hinges and rollers. If necessary, employ a qua...
