Linear CCM-2A - Manual

Copyright © 2009 Linear LLC

229333 A

CCM-2A

Color
Camera
Module

Installation Instructions

PRODUCT DESCRIPTION

Linear’s Model CCM-2A (P/N ACP00936A) CCTV camera can be installed inside the
RE-2 Residential Telephone Entry System. The camera provides a video signal for
viewing the area in front of the entry system.

The camera is continuously powered by the RE-2. Focus has been factory adjusted to
a range of three to four feet. No adjustment is needed.

The

CAMERA

connector is used to connect the camera to the RE-2. The 3-conductor

cable routes power to, and video from the camera.

The RE-2 provides a video jack for connection to a video cable with a Type “BNC”
connector. Up to 400 feet of 75-ohm RG-59 video cable can be used. Longer cable
runs may require the use of a video amplifi er.

NOTE: If camera is being installed on an existing installation, system power
should be off prior to installing the camera.

1. REMOVE THE COVER PL ATE

2. PREPARE TO MOUNT THE CAMERA

3. REMOVE THE LENS CAP

4. INSTALL THE CAMERA

5. CONNECT THE CAMERA AND VIDEO CABLE

6. TEST CAMERA

LINE AR LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twenty four
(24) months. The Warranty Expiration Date is labeled on the product.

This warranty extends

only to wholesale customers

who buy direct from Linear or through Linear’s normal distribution

channels.

Linear does not warrant this product to consumers.

Consumers should inquire from

their selling dealer as to the nature of the dealer’s warranty, if any.

There are no obligations or

liabilities on the part of Linear Corporation for consequential damages arising out of or in
connection with use or performance of this product or other indirect damages with respect
to loss of property, revenue, or profi t, or cost of removal, installation, or reinstallation.

All implied warranties, including implied warranties for merchantability and implied warranties
for fi tness, are valid only until Warranty Expiration Date as labeled on the product.

This Linear

Corporation Warranty is in lieu of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization Number (RPA#).
Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

FCC NOTICE:

This device complies with FCC Rules Part 15. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause undesired operation.

USA & Canada (800) 421-1587 & (800) 392-0123

(760) 438-7000 - Toll Free FAX (800) 468-1340

www.linearcorp.com

REMOVE THE FOUR

S

ECURITY

S

CREW

S

TO OPEN THE CA

S

E

REMOVE THE

S

IX CIRCUIT

BOARD RETAINING

S

CREW

S

AND FLIP THE CIRCUIT BOARD UP

REMOVE THE TWO RETAINING

S

CREW

S

AND BRACKET

S

REMOVE THE
BLACK DOT
ON CAMERA
GA

S

KET

CAMERA
MOUNTING
AREA

REMOVE THE LENS CAP
FROM THE CAMERA LENS

CONNECT THE VIDEO CABLE FROM
THE MONITOR OR MODULATOR TO
THE RE-2'

S

VIDEO OUTPUT CONNECTOR

CONNECT THE CAMERA'

S

CABLE TO THE RE-2'

S

CAMERA CONNECTOR

CAMERA

CONNECTOR

VIDEO

OUTPUT

CONNECTOR

APPLY POWER TO THE ACCESS SYSTEM
THEN VIEW THE VIDEO MONITOR TO TEST
THE VIDEO OUTPUT FROM THE CAMERA

SECURE THE CAMERA
WITH THE TWO RETAINING
BRACKETS AND SCREWS

PLASTIC
CAMERA
GASKET

PRINTER’S INSTR

UCTIONS:

INSTR,INSTL,CCM-2A - LINEAR P/N:

229333 A - INK:

BLA

CK - MA

TERIAL:

20 LB

. MEAD BOND - SIZE:

8.500”

X 11.000”

- SCALE:

1-1