Linear 2171-4 - Manual

Encore Multi-Room Audio
Distribution System

2171-4

Single-head
IR Emitter
(4-pack)

Installation
Instructions

1. PRODUCT

DESCRIPTION

The Model 2171-4 Single-head Infrared (IR) Emitters are supplied in
a package of four and are used with the Linear Encore Multi-Room
Audio Distribution System, ENC-SIWP source input or ENC-LIWP
local input wall plates. These generic emitters can also be used
with Linear’s video hubs, 2100A and 2010 in-wall interface, or with
a 5500 series IR enabled modulator connected to a video hub.

Each emitter contains a tiny infrared LED housed in a miniature,
injection molded plastic shell. The emitters have adhesive backing
for mounting. An emitter can be installed directly on the IR sensor
window of the controlled source component or in a suitable nearby
location.

An IR emitter repeats IR remote control signals received at a room
station keypad or IR target from a handheld IR remote control.
When an IR signal is detected at a target, the signal is sent to the
IR OUT jacks on the wall plates or device. An IR emitter connected
to the IR OUT jack, repeats the same IR signal to the source
component. This allows IR remote control of source components
that are located away from the IR target.

2. EMITTER

DETAILS

3. ATTACHING EMITTER TO COMPONENT

4. CONNECTING EMITTER TO SOURCE

LIMITED WARRANTY

This Linear product is warranted against defects in material and workmanship for twenty
four (24) months.

This warranty extends only to wholesale customers

who buy direct

from Linear or through Linear’s normal distribution channels.

Linear does not warrant

this product to consumers.

Consumers should inquire from their selling dealer as to

the nature of the dealer’s warranty, if any.

There are no obligations or liabilities on the

part of Linear LLC for consequential damages arising out of or in connection with
use or performance of this product or other indirect damages with respect to loss
of property, revenue, or profi t, or cost of removal, installation, or reinstallation.

All

implied warranties, including implied warranties for merchantability and implied warranties
for fi tness, are valid only until the warranty expires.

This Linear LLC Warranty is in lieu

of all other warranties express or implied.

All products returned for warranty service require a Return Product Authorization Number
(RPA#). Contact Linear Technical Service at 1-800-421-1587 for an RPA# and other
important details.

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,2171-4 - LINEAR P/N: P691 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” x 5.500” - SCALE: 1-1

Copyright © 2009 Linear LLC

P691

Shelves

Shelves

IR Sensor

Window

IR Controlled Components

Emitter attached directly

to IR sensor window

Emitter attached to

front cabinet door directly

opposite IR sensor window

Cabinet Door

Sensor attached on shelf directly

above or below IR sensor window

> Peel off the adhesive cover and affix the emitter to the center of the IR sensor
window on the controlled component's front panel

> In some cases, it may be difficult to find the location of the IR sensor on the
component. Consult the owner's manual of the unit for the IR sensor location.

Connect IR emitter to source
input wall plate IR OUT jack
or to the IR OUT jack provided
on other sources

ENC-SIWP
Source Input
Wall Plate

To IR emitter

(

–

)

(

+

)

7 FT

3 FT

9/16"

5/16"

1/4"

Side View

Top View

NOTE: White side
stripe is positive (+)

3.5 mm mono

mini plug

Internal

IR Emitter

High

Output

Side

Low

Output

Side

Emitter

Shell

Mini-wire

Lead

Clear adhesive layer

(Replace, if necessary,

with a short piece of

2-sided supplied)

The emitter's shell, though dark in
appearance, is transparent to
infrared light. Commands from
handheld remote controls will pass
through the emitter case to the
source component.

Model 2171-4 IR Emitter

USA & Canada (800) 421-1587 & (800) 392-0123

(760) 438-7000 - Toll Free FAX (800) 468-1340

www.linearcorp.com