Lincoln Electric IM602-A - Manual

Lincoln Electric IM602-A

Lincoln Electric IM602-A – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
Page: / 49

Table of Contents:

  • Page 2 – SAFETY; WARNING; CALIFORNIA PROPOSITION 65 WARNINGS; The Above For Diesel Engines
  • Page 3 – ii
  • Page 4 – iii; Refer to
  • Page 5 – iv; PRÉCAUTIONS DE SÛRETÉ
  • Page 6 – b) radio and television transmitters and receivers
  • Page 7 – Methods of Reducing Emissions
  • Page 8 – Thank You; Please Examine Carton and Equipment For Damage Immediately
  • Page 9 – TABLE OF CONTENTS; PAGE
  • Page 10 – INSTALLATION; TECHNICAL SPECIFICATIONS – DC-655; See the OPERATION section; INPUT - THREE PHASE ONLY
  • Page 11 – CE; NRTL
  • Page 12 – SAFETY PRECAUTIONS; STACKING; ELECTRICAL INPUT CONNECTIONS; FUSE AND WIRE SIZES; Technical; GROUND CONNECTION; Technical Specifications; ELECTRIC SHOCK can kill.; FIGURE A.1 ELECTRICAL INPUT CONNECTIONS
  • Page 13 – INPUT POWER SUPPLY CONNECTIONS; Follow all national and local electrical codes.; RECONNECT PROCEDURE; Electric Shock Can Kill; • Disconnect input power before perform-; CAUTION; FIGURE A.2 Dual Voltage Machine Reconnection Procedure
  • Page 14 – OUTPUT CONNECTIONS; ELECTRODE AND WORK CABLES; LOW INDUCTANCE TERMINAL; FIGURE A.3 Output Connections
  • Page 15 – PIN; AUXILIARY POWER TABLE; 4 PIN MS TYPE RECEPTACLE
  • Page 16 – TERMINAL STRIPS
  • Page 17 – OPERATION; GENERAL DESCRIPTION; GENERAL WARNINGS
  • Page 18 – DESIGN FEATURES AND ADVANTAGES; WELDING CAPABILITY
  • Page 19 – Machine Shutdown section; CONTROLS AND SETTINGS; FIGURE B.1 CONTROL PANEL CONTROLS
  • Page 20 – Welding Performance Section; T H E R M A L P R O T E C T I O N L I G H T -; I f t h e; 15VAC DUPLEX RECEPTACLE (Domestic and; This receptacle provides up to; FIGURE B.2 LOWER CASE FRONT CONTROLS & CONNECTIONS
  • Page 21 – MS Type Receptacle; CASE BACK CONNECTIONS; 2 0 VA C A U X I L I A RY R E C E P TA C L E; AUXILIARY POWER; MACHINE PROTECTION; THERMAL FAN CONTROL
  • Page 22 – THERMAL SHUTDOWN; Average Current Shutdown; IDLE SHUT DOWN TIMER; WELDING PERFORMANCE
  • Page 23 – CV MODE CURRENT-LIMITING; Machine Protection; CC MODE ARC FORCE; DC-655 Control PC Board
  • Page 24 – ACCESSORIES; SEMI-AUTOMATIC WIRE FEEDERS
  • Page 25 – Provides interconnection of
  • Page 26 – MAINTENANCE; GENERAL MAINTENANCE; The fan motor has sealed bearings which require
  • Page 27 – TROUBLESHOOTING; Local Lincoln Authorized Field Service Facility; for technical troubleshooting assistance before you proceed.; Step 3. RECOMMENDED COURSE OF ACTION; HOW TO USE TROUBLESHOOTING GUIDE
  • Page 28 – PROBLEMS; Local Lincoln Authorized
  • Page 31 – Machine
  • Page 35 – Remote Control Leads Fault Protection Shutdown
  • Page 36 – Observe all Safety Guidelines detailed throughout this manual; BOARD; Fan will run for minimum of 5 minutes once fan turns on.
  • Page 37 – DIAGRAMS; OR
  • Page 42 – particular code is pasted
  • Page 43 – particular code is pasted inside
Loading the manual

DC-655

OPERATOR’S MANUAL

IM602-A

February, 2009

Safety Depends on You

Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thought-
f u l o p e r a t i o n o n y o u r p a r t .

D O

N O T I N S T A L L , O P E R A T E O R
R E P A I R T H I S E Q U I P M E N T
W I T H O U T

R E A D I N G

T H I S

M A N U A L A N D T H E S A F E T Y
P R E C A U T I O N S C O N T A I N E D
T H R O U G H O U T .

A n d ,

m o s t

importantly, think before you act
and be careful.

For use with machine Code Number 10501 thru 10510, 11324

• Sales and Service through Subsidiaries and Distributors Worldwide •

Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEB SITE: www.lincolnelectric.com

• World's Leader in Welding and Cutting Products •

Copyright © Lincoln Global Inc.

RETURN TO MAIN MENU

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - SAFETY; WARNING; CALIFORNIA PROPOSITION 65 WARNINGS; The Above For Diesel Engines

FOR ENGINEpowered equipment. 1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running. ____________________________________________________ 1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumesoutdoors. ...

Page 3 - ii

ii SAFETY ii ARC RAYS can burn. 4.a. Use a shield with the proper filter and cover plates to protect your eyes from sparks andthe rays of the arc when welding or observingopen arc welding. Headshield and filter lensshould conform to ANSI Z87. I standards. 4.b. Use suitable clothing made from durable...

Page 4 - iii; Refer to

iii SAFETY iii FOR ELECTRICALLYpowered equipment. 8.a. Turn off input power using the disconnect switch at the fuse box before working onthe equipment. 8.b. Install equipment in accordance with the U.S. National Electrical Code, all local codes and the manufacturer’srecommendations. 8.c. Ground the ...

Other Lincoln Electric Models

All Lincoln Electric Other