Lennox 506033-35 - Manual

Lennox 506033-35 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

Page 2 – Figure 2; INSTALLATION INSTRUCTIONS; Removing Existing Blower From Stove; allen screws from blower, and remove blower from stove. See; Figure 3; Fan nut is; Figure 4; Step 7. Strip blower wires and connect butt connectors to both. See; Figure 6
Page 3 – Step 9. Placing edge of wire loom at edge of blower cage, connect the; black blower lead wires to the wires on the blower harness, using; Figure 9; Step 0. Reconnect the new ground wire to the motor stud. See Figure; Step . Slide the heat shrink tube to the motor, covering wires and con-; Crimp on butt connectors to both wires
Page 4 – Figure 16 - This increased opening between the pedestal and; Firebox; WOODSTOVES WITh pEDESTAL BASE; Leg based units, see instructions on; Back View of Pedestal; Bolts; Step 3. Secure wires in the heat shrink tube to the fan cage using (3); Step 5. Reinstall the blower assembly as shown in Figure 2 and the; over tighten as you may strip the holes out.; Wires / heat Shrink Tube
Page 5 – This bolt was holding the stoves shipping legs
Page 6 – Left heat Shield Bolt; Step 2. Plug the power cord into a grounded 120 VAC receptacle. Do; Snap Switch Bracket
Page 8 – Figure 34 - Wiring Schematic; Blower Speed Control; Blower Operation

Loading the manual

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

FREESTANDING BLOWER SNAp SWITCh RETROFIT KIT

COUNTRY COLLECTION™ WOODSTOVES

p/N 506033-35

Rev. NC, /2009

HEARTH PRODUCTS

KITS AND ACCESSORIES

KIT CONTENTS

1 ea. Blower Wire Harness (item #1)

1 ea. Snap Switch and Control Panel Housings (item #2)

1 ea. 6” of 3/4” Heat Shrink Tube (item #3)

2 ea. Butt Connectors (item #4)

3 ea. Wire Ties (item #5)

1 ea. Instruction Sheet

TOOLS NEEDED

5/32 Allen Wrench Or T Handle Wrench

Cutting Pliers

Wire Crimpers

9/16” Socket Wrench

9/16” Open End Wrench

Crescent Wrench

3/8” End Wrench

Large Flat Head Screwdriver

FPO

INSTALLATION INSTRUCTIONS FOR INSTALLING A BLOWER SNAp SWITCh
RETROFIT KIT FOR USE WITh COUNTRY COLLECTION™ MODELS S60, SA60,
SS20, ST20, S260 AND ST30 FREESTANDING WOODSTOVES

WARNINGS

The blower must be plugged directly into a properly

grounded three-prong receptacle, 20 VAC, 60 hz, single

phase. Do not cut or remove the grounding prong from

this plug. Do not route power cord under or in front of

appliance.

Installation must be in accordance with National Elec-

trical Code, ANSI/NFpA 70 - latest edition. In Canada,

the current CSA C22- Canadian Electrical Code - latest

edition.

DANGER: Disconnect power before servicing blower.

In the event that you remove the blower for any reason,

make sure a cover plate (available from Lennox hearth

products) is installed before using the heater. Excessive

rear wall temperatures will result if the stove is burned

without the cover plate. The cover plate is not necessary

if a blower has never been installed because a knock-out

will be in place to act as the cover.

FREESTANDING BLOWER SNAp SWITCh RETROFIT KIT

Cat. No.

Model

Description

h798

SSK-BLWR-FSB700 Blower Retrofit Kit, FS Woodstoves

Figure 1 - Kit Contents

GENERAL INFORMATION

This retrofit kit works in conjunction with the optional 700-CFM room air

circulation blower kit. The kit provides a variable speed control (rheostat)

and snap switch, which will allow for the option of automatic thermal

activation of the blower, when desired and blower speed control (see

Blower Operation on

Page 8

)

If you encounter any problems, need clarification of these instructions or

are not qualified to properly install this kit, contact your local distributor

or dealer.

Read this instruction sheet in its entirety before beginning the installa-

tion.

ALL WARNINGS AND pRECAUTIONS IN ThE INSTALLATION AND

OpERATION MANUAL pROVIDED WITh ThE AppLIANCE AppLY TO

ThESE INSTRUCTIONS.

ShUT DOWN ThE STOVE AND ALLOW IT TO COMpLETELY COOL BEFORE

pROCEEDING.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Figure 2; INSTALLATION INSTRUCTIONS; Removing Existing Blower From Stove; allen screws from blower, and remove blower from stove. See; Figure 3; Fan nut is; Figure 4; Step 7. Strip blower wires and connect butt connectors to both. See; Figure 6

2 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Figure 2 Stove Back Blower INSTALLATION INSTRUCTIONS Removing Existing Blower From Stove Step . UNpLUG pOWER CORD AND ENSURE AppLIANCE IS COLD Step 2. Using a 5/32 allen wrench/T-handle, remove the blower mounting allen screws from blower, and r...

Page 3 - Step 9. Placing edge of wire loom at edge of blower cage, connect the; black blower lead wires to the wires on the blower harness, using; Figure 9; Step 0. Reconnect the new ground wire to the motor stud. See Figure; Step . Slide the heat shrink tube to the motor, covering wires and con-; Crimp on butt connectors to both wires

3 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Figure 7 Step 8. Slide the supplied 6” of 3/4” heat shrink tube over the (3) blower harness wires. See Figure 8. Figure 8 Step 9. Placing edge of wire loom at edge of blower cage, connect the black blower lead wires to the wires on the blower ha...

Page 4 - Figure 16 - This increased opening between the pedestal and; Firebox; WOODSTOVES WITh pEDESTAL BASE; Leg based units, see instructions on; Back View of Pedestal; Bolts; Step 3. Secure wires in the heat shrink tube to the fan cage using (3); Step 5. Reinstall the blower assembly as shown in Figure 2 and the; over tighten as you may strip the holes out.; Wires / heat Shrink Tube

4 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Step 3. Insert snap switch bracket mounting tabs between the pedestal and the firebox bottom. See Figure 17. Figure 16 Step 2. Insert a large flat head screwdriver or pry bar into the small open- ing between the pedestal mounting flange and the ...