Lennox 506033-34 - Manual
Lennox 506033-34 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Figure 2; WOODSTOVES WITh PEDESTAL BASE; Leg based units, see instructions on; INSTALLATION INSTRUCTIONS; Install Blower Assembly; Figure 3; Back View of Pedestal
- Page 3 – Step 5. With the snap switch bracket in place, using a 9/16” wrench or; Step 6. Locate the 3/8” diameter x 1/2” long bolt on the bottom of the; Figure 8; Step 7. Locate front slot on the Control Box as shown in; Figure 7
- Page 4 – Figures; Step 2. Plug the power cord into a grounded 120 VAC receptacle. Do
- Page 5 – Step 7. Plug the power cord into grounded 120 VAC receptacle. Do
- Page 6 – Blower Operation Guidelines; Figure 22 - Wiring Schematic; Blower Speed Control
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
BLOWER KITS
COUNTRY COLLECTION™ WOODSTOVES
P/N 506033-34
Rev. NC, /2009
HEARTH PRODUCTS
KITS AND ACCESSORIES
KIT CONTENTS
1 ea. Blower Assembly (item #1)
1 ea. Snap Switch and Control Panel Housings (item #2)
1 ea. Instruction Sheet
TOOLS NEEDED
5/32 Allen Wrench Or T Handle Wrench
9/16” Socket Wrench
9/16” Open End Wrench
Large Flat Head Screwdriver
FPO
INSTALLATION INSTRUCTIONS FOR INSTALLING BLOWER
KITS FOR USE WITh COUNTRY COLLECTION™ MODELS S60, SA60, SS20,
ST20, S260 AND ST30 FREESTANDING WOODSTOVES
WARNINGS
The blower must be plugged directly into a properly
grounded three-prong receptacle, 20 VAC, 60 hz, single
phase. Do not cut or remove the grounding prong from
this plug. Do not route power cord under or in front of
appliance.
Installation must be in accordance with National Elec-
trical Code, ANSI/NFPA 70 - latest edition. In Canada,
the current CSA C22- Canadian Electrical Code - latest
edition.
DANGER: Disconnect power before servicing blower.
In the event that you remove the blower for any reason,
make sure a cover plate (available from Lennox hearth
Products) is installed before using the heater. Excessive
rear wall temperatures will result if the stove is burned
without the cover plate. The cover plate is not necessary
if a blower has never been installed because a knock-out
will be in place to act as the cover.
ThERMALLY ACTIVATED BLOWER KIT
Cat. No.
Model
Description
h797
BLWR-FSB700-SS
Blower Kit, FS Woodstoves
Figure 1 - Kit Contents
GENERAL INFORMATION
This optional blower kit can be installed to improve hot air distribution
throughout the room. The 700-CFM room air circulation blower kit comes
with a variable speed control (rheostat) and an snap switch which will
provide automatic thermal activation of the blower, when desired (see
Blower Operation on Page 6)
.
If you encounter any problems, need clarification of these instructions or
are not qualified to properly install this kit, contact your local distributor
or dealer.
Read this instruction sheet in its entirety before beginning the installa-
tion.
ALL WARNINGS AND PRECAUTIONS IN ThE INSTALLATION AND
OPERATION MANUAL PROVIDED WITh ThE APPLIANCE APPLY TO
ThESE INSTRUCTIONS.
ShUT DOWN ThE STOVE AND ALLOW IT TO COMPLETELY COOL BEFORE
PROCEEDING.
2
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Figure 2 WOODSTOVES WITh PEDESTAL BASE Leg based units, see instructions on Page 4 . Step . From rear of stove, using a 9/16” wrench or socket, loosen both left and right pedestal mounting bolts but do not fully remove the bolts from threaded ho...
3 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Step 5. With the snap switch bracket in place, using a 9/16” wrench or socket wrench you can now tighten down both left and right side pedestal bolts. See Figure 7 . Step 6. Locate the 3/8” diameter x 1/2” long bolt on the bottom of the firebox ...
4 WOODSTOVES WITh LEG BASE Step . Using a 9/16” wrench or socket loosen the left heat shield bolt. This bolt is located on the bottom side of the leg heatshield as shown. See Figure 14 . Figure 14 Step 2. Insert snap switch bracket between the heatshield and the bottom of firebox making sure entire ...
