KTI Networks KS-220F/C - Manual

Page 6 - Features

-2- Features Complies with IEEE 802.3u 100BASE-TX 100BASE-FX and IEEE 802.3 10BASE-T specifications 2 switched ports: Port 1 - 10/100M TP port Port 2 - configurable 10/100M TP port or 100M Fiber port The TP ports support: - auto speed sensing for 100Mbps or 10Mbps connection - auto-negotiation...

Page 7 - Specifications

-3- Specifications Standard: 10BASE-T, 100BASE-TX, and 100BASE-FX Connectors: Port 1 - 2 RJ-45 jacks Port 2 - 2 RJ-45 jacks and 1 fiber connector Cables: 10BASE-T - Cat. 3, 4, or 5 UTP cable 100BASE-TX - Cat 5 UTP cable 100BASE-FX - 62.5/125 µ m MM fiber 100BASE-FX - 9/125 µ m SM fiber LED indicator...

Page 8 - The switch can be placed on a desktop as a stand-alone unit. It also

-4- 2. Installation Unpacking Check to see that you have everything before you start the installation. Installation guide The unit One AC power adapter for the switch Installation The switch can be placed on a desktop as a stand-alone unit. It also can be mounted on a magnetic-sensitive metal su...

Page 9 - Checking AC Power

-5- Checking AC Power One AC power adapter is contained in the product package. Before you begin the installation, check the AC voltage of your area. The AC power adapter which is used to supply the DC power for the unit should have the AC voltage matching the commercial power voltage in your area. ...

Page 10 - Making Network Connections; Two Switched Ports; Two switched ports are located on the front panel.; Configuration Switches; Factory Defaults

-6- 3. Making Network Connections Two Switched Ports Two switched ports are located on the front panel. Configuration Switches On rear panel, Port 1 and Port 2 have individual configuration switches as shown below: Port 1, Port 2 SW1 O f f Auto-negotiation is enabled. On Auto-negotiation is disabled...

Page 11 - TP Ports; Jack

-7- Important Note: If any change are made to the configuration switchsettings, the power to the unit must be turned off andturned on again before the changes can take effect. The auto-negotiation mode enables the port to negotiate a common operation mode with the device connected at the remote end ...

Page 12 - UTP Connections; Compliant UTP Cables

-8- UTP Connections The following figure shows a UTP connection from TP port to another device via a straight-through UTP cable. When TP port of Port 2 is used, make sure Port 2 SW4 is set to OFF position. Depending on the configuration switch setting, the operating modes used for connecting to diff...

Page 13 - Fiber Port and Fiber Connection; Fiber Cables

-9- Fiber Port and Fiber Connection When connecting to a 100BASE-FX device using fiber cable, make sure Port 2 SW4 is set to ON position and TX-to-RX connection rule is followed. Since the fiber connector does not support auto-negotiation func- tion, it is recommended to set SW1 to ON position for t...

Page 14 - Applications

-10- MULTIMODE FIBER CABLE Connected device Duplex type Maximum length 100Base-FX NIC card Half-duplex 400 meters 100Base-FX NIC card Full-duplex 2K meters 100Base-FX hub port *1 Half-duplex 185 meters 100Base-FX hub port *2 Half-duplex 110 meters 100Base-FX switched port Half-duplex 400 meters 100B...

Page 15 - Interpreting LED Indicators; The following figure shows the locations of the LED indicators:

-11- 4. Interpreting LED Indicators The following figure shows the locations of the LED indicators: P o w e r State Indication Interpretation On Normal The power of the unit is on. O f f Problem No power is being supplied to the unit. Link/Act. (Link/Activity) State Indication Interpretation On Norm...

KTI Networks KS-220F/C - Manual

Table of Contents:

Summary

Other KTI Networks Models