KTI Networks KPOE-800-1P – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Table of Contents:
Page 2 – without permission from KTI Networks Inc.; United States; BOX; International
Page 4 – Table of Contents
Page 7 – Model Definition
Page 10 – Mounting the Injector; Desktop Mounting; Use the bracket set1 and follow the steps shown below:
Page 11 – Mounting two units in a rack
Page 12 – Mount two device units as one in a 19” rack.; Installing Power Module; connections before making any connections.
Page 13 – Screw the module in the injector securely.; Applying AC Power; Specifications
Page 14 – Making LAN Connections; Making Switch Port Connections; Port Configuration; Enable or disable; Network Cables; To make a switch port connection, the steps are:
Page 15 – Making Powered Device Connections
Loading the manual
Modular 8-Port Mid-span
Power over Ethernet Injector
KPOE-800-1P KPOE-800-2P
Installation Guide
1
DOC.090201
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Page 2 - without permission from KTI Networks Inc.; United States; BOX; International
(C) 2008 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form or by any means or used to make any directive work (such as translation or transformation) without permission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documen...
Page 4 - Table of Contents
Table of Contents 1. Introduction ................................................................................................................................5 1.1 Features.................................................................................................................5 1.2 Produ...
Page 7 - Model Definition
1.4 Model Definition KPOE-800-1P 1 Power Model The injector unit with one pre-installed power module KPOE-800-2P 2 Power Model The injector unit with two pre-installed power modules KPOE-800P60W Power Module PoE 60W Power Module KPOE-800BSET1 BRACKET SET1 The bracket set for mounting one unit in a 1...
Page 10 - Mounting the Injector; Desktop Mounting; Use the bracket set1 and follow the steps shown below:
2.3 Mounting the Injector Desktop Mounting The injector can be mounted on a desktop or shelf. Make sure there is proper heat dissipation from and adequate ventilation around the device. Do not place heavy objects on the device. Rack Mounting The following brackets are designed for use to mount the d...
Page 11 - Mounting two units in a rack
2. Install the long bracket to the other side of the device. 3. Mount the device in a 19” rack. Mounting two units in a rack Use the bracket set 2 and follow the steps shown below: Short bracket x 4 Joint bracket x 1 1. Install two short brackets to both sides of each device. 2. Joint two units toge...
Page 12 - Mount two device units as one in a 19” rack.; Installing Power Module; connections before making any connections.
3. Mount two device units as one in a 19” rack. 2.4 Installing Power Module If you purchased 2 Power Model, you may skip this section. 1 Power Model can deliver total up to 60W for consuming by all eight ports. Calculate the total power budget required for your PD connections before making any conne...
Page 13 - Screw the module in the injector securely.; Applying AC Power; Specifications
3. Install the power module into the slot until it is seated properly. 4. Screw the module in the injector securely. 2.5 Applying AC Power One AC power cord, which meets the specification of your country of origin was supplied with the device unit. The device supports wide range of AC power input sp...
Page 14 - Making LAN Connections; Making Switch Port Connections; Port Configuration; Enable or disable; Network Cables; To make a switch port connection, the steps are:
3. Making LAN Connections 3.1 Making Switch Port Connections The mid-span injector is designed to support the following PoE incapable switch port types and the PoE function is transparent and independent to the following port configuration: IEEE 802.3 std. 10BASE-T 100BASE-TX 1000BASE-T Port Configu...
Page 15 - Making Powered Device Connections
3.2 Making Powered Device Connections The mid-span injector supports connection to IEEE 802.3af compliant PoE PD (Powered Device). The Ethernet port of the PD can be Ethernet, Fast Ethernet or Gigabit Ethernet. The injector’s PoE OUT port delivers power together with network signal to a connected po...