Page 2 - 997 KTI Networks Inc. All rights reserved. No part of this docu-; United States
Ó 1997 KTI Networks Inc. All rights reserved. No part of this docu- mentation may be reproduced in any form or by any means or used tomake any directive work (such as translation or transformation) withoutpermission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documenta...
Page 3 - Installation Guide
10/100 Fast Ethernet Switch Installation Guide DOC.971006-KS2028-NK P/N: 750-0087-002
Page 4 - CE
The information contained in this document is subject to change without prior notice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class A digital device,pursuant t...
Page 6 - Figure 1-1 Switch Unit; The key features of this switch unit are:
1. Introduction Driven by recent advances in desktop computing technology, today’snetwork applications have grown speed, power and the ability to pro-cess information. To meet the demands of these more powerful applica-tions, the switch has been developed to alleviate congestion and im-prove perform...
Page 9 - Installing the Switch; Mounting the Switch; Figure 2-1 Desktop Mounting
2. Installing the Switch The switch is designed to operate in workgroup environments without acomplicated configuration procedure. It also features an auto-select 100-240V, 50/60Hz power supply unit, which works in most countries aroundthe world. Before connecting the supplied power cord into the sw...
Page 11 - Front Panel and Rear Panel; Figure 2-4 Components on the Front and Rear Panel
2.3 Front Panel and Rear Panel Figure 2-4 Components on the Front and Rear Panel • Eight 10BASE-T switched ports (Port #1 to Port #8) Each port consists of an RJ-45 connector and is used for connec-tion to a 10BASE-T hub or node. • One 10/100BASE-TX switched port (Port #9) The port consists of an RJ...
Page 12 - Installing an Optional Port Module
• Diagnostic LED indicators The indicators provide the operating status of the hub and thenetwork ports. The status includes power, partition, duplex,activity, and collision. • Configuration switches Two configuration switch groups are located on the rear of the switchunit. The switches are used for...
Page 13 - Figure 2-7 Remove the Slot Cover; Secure it to front panel.; Figure 2-8 Insert Module into the Slot
Figure 2-6 100BASE-FX Port Module Before installing any optional modules, first turn the power to the switchoff. To install a module into the expansion port slot, follow these steps: 1. Turn off the power switch. 2. Remove the cover of the slot. Figure 2-7 Remove the Slot Cover 3. Align the connecto...
Page 14 - Setting the Configuration Switches; Figure 2-9 Configuration Switches; The following table specifies the definition of each switch:
2.5 Setting the Configuration Switches Open the configuration switch cover on the rear of the unit. There aretwo switch groups as illustrated below: Figure 2-9 Configuration Switches The following table specifies the definition of each switch: The M switch only functions for Port #9 and Port #10. Si...
Page 16 - Making Network Connections; Network Switched Ports; Figure 3-1 Network Ports
3. Making Network Connections 3.1 Network Switched Ports There are ten ports on the switch for connection to ten LAN segments.Each segment is an independent shared network in one collision-do-main. Figure 3-1 Network Ports Port #1 to Port #8 are 10Mbps-based 10BASE-T switched ports anddedicated for ...
Page 18 - The following table lists the devices to which Port #8 can connect :
The following table lists the devices to which Port #8 can connect : Device connected Crossover SW Cable used Computer 10BASE-T port X setting Cat. 3, 5 straight UTP 10BASE-T hub port (I type) X setting Cat. 3, 5 straight UTP 10BASE-T hub port (X type) I setting Cat. 3, 5 straight UTP 10BASE-T switc...
Page 19 - Cable Type and Maximum Length
3.3 10/100BASE-TX Switched Ports This section applies to the 10/100BASE-TX Port #9 and expansion slotPort #10 pre-configured with a 10/100BASE-TX port module. Use thecrossover switch to set the type of RJ-45 connector as follows: The following table lists the devices to which the ports can connect: ...
Page 20 - m fiber cable. The maximum distance between the module and the
3.4 100BASE-FX Module The 100BASE-FX port module supports a connection to a Fast Ethernetnetwork segment through a fiber optic connection. The module comeswith two ST connectors. One labeled Tx is used for transmission. Theother one labeled Rx is used for reception. Figure 3-3 100BASE-FX Port Module...
Page 21 - Figure 4-1 LED Indicators
4. LED Indicators 4.1 LED Panel The switch provides comprehensive LED indicators for diagnosing andmonitoring the operation of the unit as illustrated below: Figure 4-1 LED Indicators 4.2 Interpretation One Power LED indicates the status of the power supplied to the switch. Each port has two LEDs to...