KTI Networks 10BASE-T - Manual

Ó 1998 KTI Networks Inc. All rights reserved. No part of this docu- mentation may be reproduced in any form or by any means or used tomake any directive work (such as translation or transformation) withoutpermission from KTI Networks Inc. KTI Networks Inc. reserves the right to revise this documenta...

Page 3 - Installation Guide

8-Port Dual-SpeedEthernet/Fast Ethernet Hub Installation Guide DOC.980330-KF8D-NK P/N: 750-0109-002

Page 4 - CE

The information contained in this document is subject to change without prior no-tice. Copyright Ó KTI. All Rights Reserved. TRADEMARKS Ethernet is a registered trademark of Xerox Corp. WARNING: This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant ...

Page 7 - Features

Features • Complies with IEEE 802.3 and IEEE 802.3u standard for Ethernet/Class II Fast Ethernet repeater • Provides a configuration switch (10M/100M/AUTO) to set all 8 TP ports as 10BASE-T ports, 100BASE-TX ports or 10/100auto-sensing ports. • In AUTO mode, each TP port can support either an Ethern...

Page 8 - Dual-speed Hub Technology

Dual-speed Hub Technology Dual-speed hub is designed to support connections with differentspeeds in the same hub. It makes a network planning simpler, espe-cially when an environment is containing 10Mbps Ethernet and100Mbps Fast Ethernet technologies. It also allows a smooth mi-gration from an Ether...

Page 9 - Unpacking; • The hub unit; Checking AC Power

2. Installation Unpacking Check to see that you have everything before you start the installation.• Installation guide • The hub unit • One AC power adapter for the hub • One wall mount kit Checking AC Power Before you begin the installation, check the AC voltage of your area.The AC power adapter wh...

Page 10 - Mounting the Hub; Using the slot bracket and two washer-head screws in the wall

The power socket for the AC power adapter is located on the rear ofthe hub as shown below: Mounting the Hub The hub can be placed on a desktop as a stand-alone unit. It also canbe mounted on a wall. The following procedure describes how tomount the hub onto a wallboard or wood (a stud, heavy woodenp...

Page 12 - Making Network Connections; Network Connectors and Rear Switch

3. Making Network Connections Network Connectors and Rear Switch The hub provides 8 dual-speed TP ports. Each can support one con-nection to either a 10BASE-T Ethernet device or a 100BASE-TX FastEthernet device using 2-pair UTP cable. One configuration switch islocated on the rear panel. The switch ...

Page 13 - UTP Cables

RJ-45 Connectors Each of Port #1 to Port #7 provides one RJ-45 connector, which areimplemented as MDI-X jack. An MDI-X jack is designed withinternal crossover function. The function allows a connection to acomputer using straight-through UTP cable. The Port #8 providesone MDI-X RJ-45 connector and o...

Page 15 - Connecting to Hubs; Between any two end-nodes in a collision domain, there may be

Connecting to Hubs The following table lists the types and the maximum number of hubconnections depending on the configuration switch setting: Configuration Types of hubs C o n n e c t i o n s 10M mode 10BASE-T hubs up to 8 100M mode 100BASE-TX Class II hub one 100M mode Dual-speed Class II hub one ...

Page 17 - Interpreting LED Indicators; The following figure shows the locations of the LED indicators:; Power LED: indicates the status of the repeater power source.

4. Interpreting LED Indicators The following figure shows the locations of the LED indicators: Power LED: indicates the status of the repeater power source. State Indication Interpretation On Normal The power of the hub is on. O f f Problem No power is being supplied to the hub. Collision LED: indic...

KTI Networks 10BASE-T - Manual

Table of Contents:

Summary

Other KTI Networks Models