Page 3 - CONTENTS; - READ ALL INSTRUCTIONS CAREFULLY BEFORE STARTING -
- READ AND SAVE THESE INSTRUCTIONS - CONTENTS IMPORTANT SAFETY INSTRUCTIONS.................................................................................... 1 COMPONENTS OF PACKAGE ................................................................................................. 3 INSTALLATION ......
Page 4 - WARNING; : TO REDUCE THE RISK OF PERSONAL INJURY IN THE EVENT OF A RANGE
1 IMPORTANT SAFETY INSTRUCTIONS - PLEASE READ THIS SECTION CAREFULLY BEFORE INSTALLATION - WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, OBSERVE THE FOLLOWING: 1) Installation and electrical wiring must be done by qualified professionals and in accordance with all applicabl...
Page 5 - CAUTION
2 What to Do In The Event Of a Range Top Grease Fire • SMOTHER FLAMES with a close fitting lid, cookie sheet, or metal tray, and then turn off the burner. KEEP FLAMMABLE OR COMBUSTIBLE MATERIAL AWAY FROM FLAMES. If the flames do not go out immediately, EVACUATE THE AREA AND CALL THE FIRE DEPARTMENT ...
Page 6 - COMPONENTS OF PACKAGE; (Must keep all material for returns or refunds); R ANG E HO O D BO X
3 COMPONENTS OF PACKAGE (Must keep all material for returns or refunds) O P T I O NA L R E CI RC U LA T I NG K I T A LS O A V A I LA B LE . F O R M O RE I NF O RM A T I O N, P LE A S E V I S I T O UR W E B S I T E W W W . KO BE R AN G E HO O DS . CO M O R CO NT A CT K O B E RA NG E HO O DS A T ( 62 ...
Page 7 - INSTALLATION; PLEASE READ ENTIRE INSTRUCTION BEFORE PROCEEDING; C = Height of Counter Top to Hood Bottom
4 INSTALLATION PLEASE READ ENTIRE INSTRUCTION BEFORE PROCEEDING Calculation before Installation To calculate installation, please refer to Table 1. (All calculation in inches.) - FOR UNDER THE CABINET - TABLE 1 A = Height of Floor to Ceiling B = Height of Floor to Counter Top (Standard: 36”) C = Hei...
Page 9 - Figure 3
6 UNDER THE CABINET INSTALLATION Preparation Before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the hood to the outside. Refer to Figure 1. • A straight, short vent run will allow the hood to perform m...
Page 10 - S A F E T Y W A R N I N G; DONE; Final Assembly; Figure 5
7 Ductwork Installation 8. Use 8” round steel pipe (follow building codes in your area) to connect the ducting transition on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer to Figure 5. Wiring to Power Supply S A F E T Y W A R N I N G RISK OF ELECTRICAL S...
Page 11 - Turn power ON in control panel. Check all lights and
8 14. Turn power ON in control panel. Check all lights and fan operation. 15. Make sure to leave this manual for the homeowner Figure 8
Page 12 - Figure 10
9 WALL MOUNT INSTALLATION ***F ollow these installations only if installing with an optional duct cover: Preparation Before Installation NOTE: TO AVOID DAMAGE TO YOUR HOOD, PREVENT DEBRIS FROM ENTERING THE VENT OPENING. • Decide the location of the venting pipe from the hood to the outside. Refer to...
Page 13 - Align hood-mounting bracket to the two screws; CAUTION: MAKE SURE HOOD IS SECURE; W i ri ng t o Po we r S up p l y; SAFETY WARNING; ACCORDANCE; . Co n ne ct th e e le ct rica l wire s.
10 mark the leveling point of the hood. Position two mounting screws (not included) on the wall, leaving 1/8” away from the wall. Refer to Figure 13 2. Align hood-mounting bracket to the two screws on the wall and hook hood into place. Tighten screws to secure hood to the wall. 3. For safety purpose...
Page 14 - Duct Cover Installation; Use duct tape
11 Duct Cover Installation 5. Use 8” round steel pipe (follow building codes in your area) to connect the ducting transition on the hood to the ductwork above. Use duct tape to make all joints secure and air tight. Refer Figure 15. Slide the duct cover onto the hood. 6. Use 3/16” x 3/8” screws (incl...
Page 15 - OPERATING INSTRUCTIONS; Press Speed Control A button to cycle from Low, QuietMode
12 OPERATING INSTRUCTIONS This KOBE hood is equipped with four electronic controls with a 10-second standby startup & 30-second delay shutoff, powerful centrifugal squirrel cage with baffle filters, bright 12-volt 20-watt halogen lights, and heating lamp sockets (lamps not included). The four el...
Page 16 - MAINTENANCE; To Clean Hood Surface; Caution: Do not leave on too long as this may cause damage; installation in reverse.
13 MAINTENANCE SAFETY WARNING NEVER PUT YOUR HAND INTO AREA HOUSING THE FAN WHILE THE FAN IS OPERATING. For optimal operation, clean range hood and all baffle/spacer/filter/oil tunnel/oil container regularly. To Clean Hood Surface CAUTION : NEVER USE ABRASIVE CLEANERS, PADS, OR CLOTHS. *** Regular c...
Page 17 - To Replace Light Bulb; HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL.; to remove cover
14 To Replace Light Bulb CAUTION : HALOGEN LIGHT UNIT MAY BE HOT! WAIT UNTIL UNIT IS COOL. 1. Make sure all controls are off, and range hood is unplugged. 2. Place a flat-head screwdriver between light cover and housing to remove cover . 3. Gently pull defective bulb straight out and discard. Light ...
Page 18 - SPECIFICATIONS
15 SPECIFICATIONS CH0030SQB / 30“ CH0036SQB / 36“ CH0042SQB / 42“ MODEL / SIZE CH0048SQB / 48“ COLOR #304 Commercial Grade Stainless Steel CONSUMPTION / AMPERE 900W / 8A VOLTAGE 120V 60Hz NUMBER OF MOTORS 1 DESIGN 18 Gauge Seamless / Satin Finish FAN TYPE: CENTRIFUGAL Squirrel Cage EXHAUST Top Trans...
Page 19 - MEASUREMENTS & DIAGRAMS; - F O R U N D E R T H E C A B I N E T -
16 MEASUREMENTS & DIAGRAMS All ( ) are in millimeter. All inch measurements are converted from millimeters. Inch measurements are estimated. - F O R U N D E R T H E C A B I N E T - MODEL NO: CH0030SQB CH0036SQB CH0042SQB CH0048SQB
Page 25 - PARTS LIST
22 PARTS LIST MODEL NO: CH0030SQB CH0036SQB CH0042SQB CH0048SQB BODY COMPONENTS NO. DESCRIPTION MODEL/SIZE PART NO. 1 Hood Casing CH100-1 2 Ducting Transition CH100-2 3 Screws (3/16” x 3/8”) CH100-3 4 Blower Assembly CH100-4 5 Wiring Box Cover CH100-5 6 Wiring Box CH100-6 7 Heat Lamp Socket CH100-7 ...
Page 29 - CIRCUIT DIAGRAM; PROCESSOR BOARD
26 CIRCUIT DIAGRAM MODEL NO.: CH0030SQB CH0036SQB MOTOR CAPACITOR 10uF/450V TRANSFORMER PROCESSOR BOARD CONTROL BOARD HALOGEN LIGHT RED BLACK WH IT E Y E L L O W G R E E N B R O WN R E D G R E E N WH IT E R E D B L A C K B L A C K WH IT E R E D 120V 60Hz
Page 31 - DISCLAIMER; DAMAGES CAUSED DURING TRANSIT ARE NOT COVERED UNDER OUR WARRANTY.
28 DISCLAIMER 1. CAREFULLY INSPECT ALL ITEMS FOR DAMAGES BEFORE ACCEPTING DELIVERY. NOTE ANY DAMAGES ON THE FREIGHT BILL OR EXPRESS RECEIPT. REQUEST NAME AND SIGNATURE OF THE CARRIER’S AGENT AND KEEP COPY TO SUPPORT YOUR CLAIM. Upon acceptance of items, owner assumes responsibility for its safe arri...
Page 32 - WARRANTY; WARRANTY CERTIFICATE; for failure of light bulbs or heat lamps
29 WARRANTY WARRANTY CERTIFICATE KOBE Range Hoods, Inc. warrants all products manufactured or supplied by it to be free from defects in workmanship and materials. Its obligations pursuant to this warranty are limited to a period of two years from the date of purchase and to the repair or replacement...
Page 34 - PRODUCT REGISTRATION
31 PRODUCT REGISTRATION Register Your Product! Any covered failure occurring within two years of original purchase arising from defective workmanship or material in manufacture will be repaired or at our option the unit will be replaced free of charge by an authorized KOBE Range Hoods Agent or KOBE ...
Page 36 - KOBE Range Hoods; Using a KOBE
KOBE Range Hoods 10505 Valley Blvd Suite # 302 El Monte, CA 91731 USA http://www.KOBERangeHoods.com This KOBE hood is manufactured for use in the USA and CANADA only. We do not recommend using this hood overseas as the power supply may not be compatible and may violate the electrical code of that co...
