Kenwood TK-8360 - Manual - manualsarea.com

Page 2 - VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER; INSTRUCTION MANUAL; ENGLISH; Firmware Copyrights

VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7360/ TK-8360 INSTRUCTION MANUAL ENGLISH Firmware Copyrights The title to and ownership of copyrights for firmware embedded in Kenwood product memories are reserved for Kenwood Corporation. NOTIFICATION This equipment complies with the essential requirements...

Page 4 - We are grateful you have chosen; Kenwood; for your personal moble applcatons.; It s mportant that the operator s aware of, and understands, hazards

T hank Y ou We are grateful you have chosen Kenwood for your personal moble applcatons. Ths nstructon manual covers only the basc operatons of your moble rado. Ask your dealer for nformaton on any customzed features they may have added to your rado. n oTices To The u ser ◆ Government law prohbts the...

Page 5 - CONTENTS; • Do not dsassemble or modfy the transcever for any reason.; and observe the vehcle regulatons n your area.

CONTENTS GeTTING STARTeD ................................................................................................1 GeTTING ACQUAINTeD .........................................................................................3 PROGRAmmAble FUNCTIONS ...............................................

Page 6 - GETTING STARTED; Power Cable Connection; power cable can be passed through.; • Place the fuse as close to the battery as possible.; Coil the surplus cable and secure it with a retaining band.; for servicing while keeping the power applied.

GETTING STARTED Note : The following instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. S upplied A cceSSorieS Carefully unpack the transceiver. We recommend that you identify the items listed below before discarding the packing material. If any ...

Page 7 - Installing the Transceiver; mounting bracket using the supplied screws.

2 n Installing the Transceiver For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set, so the transceiver will not break loose in the event of a collision. Note : Before installing the transceiver, check how far the mounting screws will extend below ...

Page 8 - GETTING ACQUAINTED; Lights blue during a specified mode, based on dealer programming.

3 GETTING ACQUAINTED F ront And r eAr V iewS ① (Power) switch Press to switch the transceiver ON or OFF. ② / keys Press to activate their programmable functions {page 5}. ③ / keys Press to activate their programmable functions {page 5}. ④ TX/RX Indicator Lights red while transmitting and green while...

Page 9 - Icon

4 d iSplAy Icon Description Displays the signal strength.Not used.Lights when the GPS position is determined.Signaling is turned off.A DTMF call is being received.The Talk Around function is on.Lights while scanning or while paused on a channel. Blinks when scan is temporarily stopped.A caller ID/me...

Page 10 - PROGRAMMABLE FUNCTIONS; keys can be programmed with the

5 PROGRAMMABLE FUNCTIONS The , , , , , S , A , , and n keys can be programmed with the functions listed below. Ask your dealer for details on these functions. • None • Auto Reply Message • Autodial • Autodial Programming • AUX • Call ~ 3 • Calling Alert • CH/GID Down • CH/GID Down (Con...

Page 11 - BASIC OPERATIONS; to confirm the password.; id

6 BASIC OPERATIONS S witching p ower on/ oFF Press to switch the transceiver ON. • A beep sounds and the display illuminates. If the Power-on tone select is set to OFF, the beep will not sound. • If the Transceiver Password function is programmed, “PASSWORD” will appear on the display. Refer to “Tra...

Page 12 - SCAN; Monitors the channels of every zone.; Scan; • “SCAN” and the icon appear on the display during scan.

t rAnSmitting / r eceiVing 1 Select your desired zone and channel. 2 Press the microphone PTT switch and speak into the microphone to transmit. Release the PTT switch to receive. • For best sound quality at the receiving station, hold the microphone approximately .5 inches (3 ~ 4 cm) from your mouth...

Page 13 - DTMF CALLS; PTT; PTT; Autodial; (if the key assignment list selection is configured as “Enabled”) or; PTT

S cAn d elete /A dd You can add and remove zones and/or channels/group IDs to and from your scan list. 1 Select your desired zone and/or channel/group ID. 2 Press the key programmed as Scan Delete/Add to remove a channel or press and hold the key for approximately second to remove a zone. • When a c...

Page 15 - SIGNALING; FleetSync Signaling:; OST; • “TONE” appears on the display, followed by the current OST number.; • You can also directly enter a number from 0 to 40 using the keypad.

0 SIGNALING Q uiet t Alk (Qt)/ d igitAl Q uiet t Alk (dQt) Your dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/code which allows you to ignore (not hear) calls from other parties who are using the same channel. o ptionAl S ignAl...

Page 16 - • You can also enter the station ID directly by using the keypad.; Call 3; my id; Selcall; FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION

2 Press the key programmed as Selcall . 3 Press / (if the key assignment list selection is configured as “Enabled”) or to select the ID of the station you want to call. • You can also enter the station ID directly by using the keypad. 4 Press the key programmed as Call 1 to Call 3 to b...

Page 17 - (if the key assignment list selection is configured as “Enabled”); • When pressing the; Status; key, the target Fleet/ ID is fixed and cannot be; (if the key assignment list selection is configured

2 n Transmitting 1 Select your desired zone and channel. 2 Press the key programmed as Selcall or Selcall + Status . 3 Press / (if the key assignment list selection is configured as “Enabled”) or to select the ID of the station you want to call. • You can also enter the station ID dire...

Page 18 - • You can also enter the status ID directly by using the keypad.; icon will flash and the calling ID or; gpS r; ADVANCED OPERATIONS; you must hold the; Emergency

3 4 Press S to enter Status mode. 5 Press / (if the key assignment list selection is configured as “Enabled”) or to select the status ID you want to transmit. • You can also enter the status ID directly by using the keypad. 6 Press the PTT switch or n to initiate the status call. n Rec...

Page 19 - Lone Worker; • The icon appears on the display while Talk Around is activated.; • The icon appears on the display while the Scrambler is activated.

4 • When the transceiver enters Emergency mode, the transceiver will change to the Emergency channel and begin transmitting based on how the transceiver is set up. 2 To exit Emergency mode, press and hold the Emergency key again. • If the Emergency mode completes the preset number of cycles, Emergen...

Page 20 - not work with transceivers set up with different scrambler codes.; Squelch Off Momentary:; Press and hold to hear background noise. Release to return

5 2 Press / (if the key assignment list selection is configured as “Enabled”) or to select your desired scrambler code. 3 Press S , , or to store the new setting. • After changing your scrambler code, be sure to inform all of your group members of the new code so they can also reset th...

Page 21 - lcd b; BACKGROUND OPERATIONS

6 p ublic A ddreSS (pA) The PA system can only be used with an external speaker. 1 Press the key programmed as Public Address to activate the Public Address function. • The icon appears on the display. 2 Press and hold the PTT switch, then speak into the microphone to make your address through the e...

Page 22 - • “BUSY” appears on the display when you press the; switch. Use a different channel; ptt id; VGS-1 OPTIONAL VOICE GUIDE & STORAGE UNIT; • The

• “BUSY” appears on the display when you press the PTT switch. Use a different channel or wait until the channel becomes free. If your dealer has programmed BCL Override for your transceiver, you can override the BCL by pressing the PTT switch again, immediately after releasing it, when the channel ...

Kenwood TK-8360 - Manual

Table of Contents:

Summary

Other Kenwood Models