Kelvinator KSV35CRH - User Manual

Page 2 - Conditions of use; bed and breakfast type environments.; ENVIRONMENTAL TIPS; environment; R300 refrigerant warning; R32 refrigerant warning; Congratulations

Congratulations and thank you for choosing our Inverter split system room air conditioner. We are sure you will find your new air conditioner a pleasure to use. Before you use the air conditioner, we recommend that you read through the entire user manual, which provides the description of the air co...

Page 3 - WARNING; caution; • Contact an authorised installer for installation of this unit.; Important safety instructions

Kelvinator Air Conditioning Impor tant safety instruc tions 3 WARNING caution 1 The unit must only be installed by a qualified refrigeration mechanic and electrical work carried out by a qualified electrician according to AS/NZS 3000 electrical installation standard and in accordance with all local ...

Page 4 - Choosing a location to mount unit; Indoor unit; Model; Minimum

4 Choosing a location Kelvinator Air Conditioning Choosing a location to mount unit Indoor unit • Do not install the unit near any heat source, ammable gas or steam. • Choose a location where the air circulation is good, and where there are no obsticles blocking the air ow. • Select a place that wil...

Page 5 - Installation drawing; Air conditioner; Flare nuts; Remote controller; User manual; Remote controller holder

Kelvinator Air Conditioning Installation drawing 5 Installation drawing NOTE: Appearance of outdoor unit and indoor unit may differ from some models. The actual shape shall prevail. Air conditioner Qty. Qty. 1 Indoor unit 1 7 Battery (AAA 1.5V) 2 2 Outdoor unit 1 8 Drain elbow & seal 1 3 Indoor ...

Page 6 - Indoor unit installation; Installation plate mounting; ti

6 Indoor unit installation Kelvinator Air Conditioning Indoor unit installation Remove the installation plate from the indoor unit. The installation plate should be installed on a wall which can support the weight of the indoor unit. Model Indoor unit dimensionsW x H x D (mm) Weight (kg) KSV25CRH KS...

Page 7 - Drilling the wall; Do not put anything inside the condensate drain pan (refer to

Kelvinator Air Conditioning Indoor unit installation 7 Indoor unit installation Drilling the wall 1. Choose the hole position to be either on the left or right side of the installation plate and mark the position according to the dimensions shown in figure 2. Note most simple installation is with ho...

Page 8 - Drain piping; Connect the cable to the indoor unit; electrician

8 Indoor unit installation Kelvinator Air Conditioning Indoor unit installation Drain piping 1. Run the drain hose as shown in figure 6, ensuring it has a constant downward fall. 2. The installer must supply a suitable drain hose extension to run from the indoor unit drain hose to the desired drain ...

Page 9 - NOTE: The wire size of power supply cord and interconnected; important; NOTE: Before performing any electrical work, turn off the main; MA TION

Kelvinator Air Conditioning Indoor unit installation 9 Indoor unit installation Recommended circuit breaker rating Model Circut breaker rating (Amps) KSV25CRH, KSV25HRH, KSD25HRH KSV50HRH, KSD50HRH, KSV71CRH, KSV71HRH, KSD71HRH KSV35CRH, KSV35HRH, KSD35HRH 15 15 20 25 KSV80HRG, KSD80HRG xxA 25 KSV90...

Page 10 - Outdoor unit installation; Be sure there is no obstacle which blocks the air flow.; Location of outdoor unit; Drain elbow installation

Outdoor unit installation WARNING caution • Install the outdoor unit on a rigid base to prevent excessive noise level and vibration. • Choose an outdoor unit location where the air outlet direction is not blocked, and the clearances as per the assembly diagram (figure 1) are followed. • In the case ...

Page 11 - Refrigerant pipe connection

Kelvinator Air Conditioning Outdoor unit installation 11 Outdoor unit installation Refrigerant pipe connection NOTE: • The connectors used to join the indoor and outdoor refrigeration pipes must be located outside. They cannot be located inside or within a wall cavity where refrigerant may build up ...

Page 12 - Flaring work; Checking flare work

12 Outdoor unit installation Kelvinator Air Conditioning Flaring work TIPS & INFORMATION important For installer It is critical that the installer follows the correct flaring procedure using the right tools to produce good quality flares in order to ensure installation without refrigerant gas le...

Page 13 - Tightening Connection; Insulating the pipes

Kelvinator Air Conditioning Outdoor unit installation 13 Outdoor unit installation Tightening Connection • Align the center of the pipes. • Sufficiently tighten the flare nut with fingers, and then tighten it with a spanner and torque wrench as shown in Fig.16 & 17. Outer diameter (mm) ø 6.35 (1...

Page 14 - Electrical connection; Wiring diagram; Installation of DRED network cable; Magnetic ring installation; Magnetic ring

14 Outdoor unit installation Kelvinator Air Conditioning Electrical connection Wiring diagram 1(L) 1(L) 2(N) 2(N) S S L N Indoor unit terminal block (3) Power supply Outdoor unit terminal block Key:1(L) = Live (Brown)2(N) = Neutral (Blue)S = Signal (White) = Earth (Yellow & Green) Installation o...

Page 15 - Test running; Air purging; NOTE: Any brazed connections must be completed before; Air purging with vacuum pump; Pipe length and refrigerant amount:; W ARNING; warning

Kelvinator Air Conditioning Test running 15 Test running Air purging Air and other foreign matter in the refrigerant circuit causes abnormal pressure rise, which may result in equipment damage and even injury. Therefore, the indoor unit and tubing between the indoor and outdoor unit must be leak tes...

Page 16 - liquid; When Using the Vacuum Pump

16 Outdoor unit installation Kelvinator Air Conditioning Outdoor unit installation • Make sure the refrigerant added into the air conditioner is liquid form. Caution in handling the service valve • To open the service valve, remove the cap then open the valve stem using an Allen key until it hits th...

Page 17 - Electrical and gas leak check; Electrical safety check

Kelvinator Air Conditioning Electrical and gas leak check 17 Electrical and gas leak check Electrical safety check Perform the electric safe check after completing installation: 1. Earth connection - Check the earth connection visually and with a multi meter following national wiring rules to confir...

Page 18 - Information servicing; Initial safety checks shall include:

18 Information servicing Kelvinator Air Conditioning Information servicing Checks to the area Prior to beginning work on systems containing flammable refrigerants, safety checks are necessary to ensure that the risk of ignition is minimised. For repair to the refrigerating system, the following prec...

Page 19 - Repairs to sealed components; NOTE: The use of silicon sealant may inhibit the effectiveness; Repair to intrinsically safe components

Kelvinator Air Conditioning Information ser vicing 19 Information servicing Repairs to sealed components 1. During repairs to sealed components, all electrical supplies shall be disconnected from the equipment being worked upon prior to any removal of sealed covers, etc. If it is absolutely necessar...

Page 20 - Charging procedures

20 Information servicing Kelvinator Air Conditioning Information servicing Charging procedures In addition to conventional charging procedures, the following requirements shall be followed: • Ensure that contamination of different refrigerants does not occur when using charging equipment. Hoses or l...

Page 21 - Notes

Page 24 - For more information on all Kelvinator

© 2018 Electrolux Home Products Pty Ltd.ABN 51 004 762 341May18_KMAN_AIRCARE_IM AUSTRALIA phone: 1300 363 640fax: 1800 350 067 email: [email protected]web: kelvinator.com.au NEW ZEALAND phone: 0800 436 245fax: 0800 225 088 email: [email protected]web: kelvinator.co.nz For more information on all Kel...

Kelvinator KSV35CRH - User Manual

Table of Contents:

Summary

Other Kelvinator Air Conditioners Models