Page 2 - Safety precaution
1-2 KS-FX725R ! Burrs formed during molding may be left over on some parts of the chassis. Therefore, pay attention to such burrs in the case of preforming repair of this system. Safety precaution
Page 3 - Disassembly method; Joint
1-3 KS-FX725R Press the eject button in the lower right part of the front panel. Remove the front panel assembly from the body. 1. Removing the front panel assembly (See Fig.1) Prior to performing the following procedure, remove the front panel assembly. Release the four joints a on both sides of th...
Page 4 - Removing the bottom cover
1-4 KS-FX725R Remove the three screws A on the left side of the body. 1. Removing the heat sink (See Fig.4) Prior to performing the following procedure, remove the front panel assembly, the front chassis assembly and the heat sink. Turn over the body and unjoint the five joints b with the bottom cov...
Page 6 - Removing the control switch board
1-6 KS-FX725R Prior to performing the following procedure, remove the front panel assembly. Remove the four screws G attaching the rear cover on the back of the front panel assembly. Unjoint the ten joints d with the front panel and the rear cover. Remove the control switch board on the back of the ...
Page 7 - Removing the reinforce bracket
1-7 KS-FX725R Remove the screw A attaching the reinforce bracket on the bottom of the body. To release joint a, turn and detach the reinforce bracket from the side bracket assembly as shown in Fig.2 1. 2. Removing the reinforce bracket (See Fig.1 and 2) Turn the mode gear to set to RVS play or subse...
Page 8 - Remove the E-washer attaching the load arm.
1-8 KS-FX725R Check the mode is set to EJECT. Push down the front part of the cassette holder and move in the direction of the arrow to release the joint f. Move the rear part of the cassette hanger assembly in the direction of the arrow to release it from the two joint bosses g. Release the holder ...
Page 9 - Removing the side bracket assembly
1-9 KS-FX725R Remove the screw C attaching the side bracket assembly. Detach the front side of the side bracket assembly upward and pull out forward to release the joint l and m in the rear. 1. 2. Removing the side bracket assembly (See Fig.10 to 12) When reassembling, make sure that the boss n of t...
Page 10 - Removing the slide chassis assembly
1-10 KS-FX725R Remove the polywasher and pull out the pinch arm (F) assembly. Remove the compulsion spring. 1. 2. Removing the pinch arm (F) assembly (See Fig.13 and 14) Remove the polywasher and pull out the pinch arm (R) assembly. 1. Removing the pinch arm (R) assembly (See Fig.13 and 15) Move the...
Page 11 - Removing the head / tape guide
1-11 KS-FX725R Remove the band attaching the wire to the head. Remove the two screws D, the head and the head support spring. Remove the pinch arm spring from the tape guide. Remove the tape guide and the pinch spring arm. 1. 2. 3. 4. Removing the head / tape guide (See Fig.18 and 19) Remove the bel...
Page 12 - Remove the two screws E attaching the reel board.; Unsolder the wires if necessary.; Removing the reel board
1-12 KS-FX725R Push and turn counterclockwise the spring holder (F) to release the three joints s on the bottom of the flywheel. The spring holder (F), the TU spring and the friction gear play come off. Remove the polywasher and felt. 1. 2. 3. Disassembling the flywheel assembly (F) (See Fig.22 and ...
Page 13 - Move the gear base arm in the direction of the arrow.; Removing the FFC pad
1-13 KS-FX725R Move the gear base arm in the direction of the arrow. Insert a slotted screwdriver to the gear base spring under the gear base arm, and release the gear base arm upward from the boss on the gear base assembly. Remove the gear base arm from the main chassis while releasing the two join...
Page 14 - Remove the polywasher attaching the direction link.; Removing the mode switch actuator
1-14 KS-FX725R Remove the polywasher on the bottom and pull out the mode gear. 1. Removing the mode gear (See Fig.30 and 33) Move the mode rack assembly in the direction of the arrow to release the two joints k’ and the joint l’. 1. Removing the mode rack assembly (See Fig.31 and 32) Remove the poly...
Page 15 - Removing the reel driver / reel spindle
1-15 KS-FX725R Push in the pin e’ of the gear base assembly on the upper side of the body and move the reflector gear toward the bottom, then pull out. Remove the polywasher on the bottom and pull out the take up gear. Move the gear base assembly in the direction of the arrow to release it from the ...
Page 16 - Remove the eject cam plate spring.
1-16 KS-FX725R Remove the eject cam plate spring. Push the joint g‘ through the slot to remove the load rack downward. Move the eject cam limiter in the direction of the arrow to release it from the boss h’ of the side bracket assembly and from the two joints i’. Move the eject cam plate in the dire...
Page 18 - Adjustment method; Test instruments reqired for adjustment
1-18 KS-FX725R Adjustment method Test instruments reqired for adjustment 1. Digital osclloscope(100MHz) 2. Frequency Counter meter 3. Electric voltmeter 4. Wow & flutter meter 5. Test tapes VT724 ....................... ................... for DOLBY level measurement VT739 ............ For playb...
Page 19 - Arrangement of adjusting & test points
1-19 KS-FX725R Head section view Cassette mechanism (Surface) Arrangement of adjusting & test points Motor assembly Tape speed adjust Playback head Azimuth screw B (Reverse) Azimuth screw B (Reverse) Azimuth screw A (Forward) Azimuth screw A (Forward) Playback Head
Page 20 - Arrangment of adjusting; Information f; or using a car audio service jig
1-20 KS-FX725R C401 C402 C403 C404 C405 C406 C407 C408 C409 C410 C411 C412 C413 C414 C416 C417 C418 C419 C421 C422 C423 C424 C425 CJ401 B405 B403 D401 D402 IC402 Q401 Q402 Q403 R401 R402 R403 R404 R405 R406 R407 R408 R410 R411 R412 R413 R414 R415 R416 R417 R418 R420 B413 R422 R423 R424 R425 R426 VR4...
Page 22 - Description of major ICs
1-22 KS-FX725R Description of major ICs UPD178018AGC584(IC701) : System controller micon 24 – 1 41 – 64 25 40 80 65 1.Terminal Layout 2.Description – – 1 KEY0 I Key input 0 2 KEY1 I Key input 1 3 KEY2 I Key input 2 4 LEVEL I Level meter input 5 SM I Signal meter input 6 SQ I Signal quality input 7 L...
Page 24 - CXA2559Q(IC401):Playback equalizer amplifier with music sensor
1-24 KS-FX725R 1.Pin layout 2.Blockdiagram 40 31 11 20 1 10 30 21 PBFB2 PBRIN2 PNGND PNFIN2 VCT PBREF PBFIN1 PBGND PBRIN1 PBFB1 MSMODE DRSW TAPESW MUTESW NC NC MSOUT MSTC G1FB G2FB PBTC2 PBOUT2 OUTREF2 T APEIN2 GND DIREF LINEOUT2 NC NC MSSW PBTC1 PBOUT1 OUTREF1 T APEIN1 NC NC LINEOUT1 NC NC MSLPF 31...
Page 28 - Pin
1-28 KS-FX725R 123456789 10111213141516 32313029282726252423222120191817 SDA GND OUTLR OUTLF TL B2LB1L IVL ILL QSL IDL MUTE ICL IMD IBLIAL SCLVCCOUTRROUTRFTRB2RB1RIVRILRQSRIDRVrefICRCAPIBRIAR CD-CH TAPE TUNER POWER SUPPLY SOURCE SELECTOR VOLUME 1 +20 to -31 dB LOUDNESS LEFT BASS LEFT +15 dB TREBLE L...
Page 31 - AB; Block diagram
AB C 1 2 3 4 5 KS-FX725R 2-1 Block diagram IC801 BUFFER HD74HC126FP-X HEAD IC401 PB EQ CXA2559Q IC301 POWER AMP. LA4743K IC161 E.VOLUME TEA6320T-X IC701 UPD178018AGC623 MAIN SYSTEM CONTROL CPU TU1 AM/FM TUNER PACK QAU0260-001 SUB MOTOR IC402 DC MOTOR DRIVER LB1641 LCD1 QLD0158-002 IC651 LCD DRIVER L...
Page 33 - Standard schematic diagrams; Receiver & System control section
Standard schematic diagrams Receiver & System control section FM Radio signal / Radio main signal AM Radio signal CD signal Cassette signal Front signal Rear signal Parts are safety assurance parts.When replacing those parts makesure to use the specified one. A B C D E F G 1 2 3 4 5 2-3 KS-FX725...
Page 34 - Mecha control circuit section; Cassette signal
Mecha control circuit section Cassette signal H A B C D E F G 1 2 3 4 5 KS-FX725R KS-FX725R 2-4 C410 CJ401 C409 C411 R416 C422 Q402 Q403 IC402 C425 C424 CJ402 R401 R418 IC401 CJ403 C416 C413 C412 D401 VR401 R408 C414 R409 C419 C415 C418 R410 R414 C406 C421 R415 R406 R407 R405 C404 R404 C403 C402 R41...
Page 35 - LCD driver & Operation switch section
LCD driver & Operation switch section A B C D E F G 1 2 3 4 5 2-5 KS-FX725R R652 IC651 C653 C651 C652 D655 D654 R602 D653 R651 S601 S603 S602 S612 S611 S608 R609 S619 S609 S610 S615 S616 S617 S618 S614 R603 IC652 R607 R608 R613 R614 R615 S607 LCD1 R606 CP701 D652 S606 D601 S604 R601 S620 S613 S6...
Page 36 - Printed circuit boards; Main board
H A B C D E F G 1 2 3 4 5 KS-FX725R KS-FX725R 2-6 Printed circuit boards Main board Front board(Forward side) Front board(Reverse side) C1 C2 C3 C4 C5 C6 C7 C8 C9 C31 C32 C33 C41 C42 C43 C51 C52 C53 C54 C55 C71 C72 C73 C74 C75 C76 C77 C81 C82 C83 C84 C161 C162 C163 C164 C165 C166 C167 C168 C169 C170...
Page 37 - PARTS LIST; Area suffix
KS-FX725R 3-1 PARTS LIST * All printed circuit boards and its assemblies are not available as service parts. - Contents - Exploded view of general assembly and parts list (Block No.M1) Cassette mechanism assembly and parts list (Block No.MP) Electrical parts list (Block No.01~03) Packing materials a...
Page 38 - Exploded view of general assembly and parts list
KS-FX725R 3-2 Exploded view of general assembly and parts list Block No. M M M 1 F ront board Mecha control board A B Main board B A 7 3 11 11 2 6 5 9 4 11 11 6 6 1 8 6 12 13 10 13 12 14 14 18 17 16 19 51 22 50 20 42 38 34 35 28 23 24 32 25 29 30 33 40 39 26 36 42 45 47 44 48 43 46 49 53 54 21 41 31...
Page 41 - Cassette mechanism assembly and parts list
KS-FX725R 3-5 Cassette mechanism assembly and parts list Block No. M M M P CDS-802JE1 86 82 84 83 87 85 22 13 74 49 48 72 12 71 2 41 60 51 31 47 21 43 10 11 7 44 37 45 40 42 61 1 6 35 26 50 23 63 67 73 91 25 4 97 98 99 27 24 59 28 17 94 64 30 34 46 3 39 66 66 38 38 32 5 62 75 93 65 33 16 116 108 104...
Page 52 - Packing materials and accessories parts list
KS-FX725R 3-16 Packing materials and accessories parts list Block No. M M M 3 Block No. M M M 5 A1~A4 P1 P6 P7 P5 A5 A12 A14 A13 P4 P7 A11 P3 KIT:A6~A10 P2
Page 54 - CASSETTE RECEIVER; РЕСИВЕР С КАССЕТНЫМ ПРОИГРЫВАТЕЛЕМ; ENGLISH; INSTRUCTIONS; ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ
GET0057-001A [EE] CASSETTE RECEIVER РЕСИВЕР С КАССЕТНЫМ ПРОИГРЫВАТЕЛЕМ ENGLISH Р УССКИЙ INSTRUCTIONS ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ KS-FX725R/KS-F525 В соответствии с Законом Российской Федерации “О защите прав потребителей” срок службы (г одности) данного товара “по истечениикоторого он может представл...
Page 55 - УССКИЙ; ОСНОВНЫЕ ОПЕРАЦИИ С; СОДЕРЖАНИЕ; Как перенастроить Ваше устройство
2 Р УССКИЙ Благодарим Вас за приобретение изделия JVC. Перед тем, как приступать к эксплуатации, пожалуйста, внимательно прочитайте все инструкции с тем, чтобы полностью изучить и обеспечить оптимальную работу этого устройства. Как перенастроить Ваше устройство .... 2 РАСПОЛОЖЕНИЕ КНОПОК ..............
Page 56 - a s; РАСПОЛОЖЕНИЕ КНОПОК; Панель управления—; Окно на экране дисплея
3 Р УССКИЙ MO 8 9 10 11 12 7 1 3 2 4 5 w 7 8 9 p y u r e t q 6 TP RDS PTY DISP DAB a s d k l g f ; o i h j РАСПОЛОЖЕНИЕ КНОПОК Панель управления— KS-FX725R 1 Кнопка (резервный/включение/ аттенюатор) 2 Диск управления 3 Кнопка DISP (дисплей) 4 Кнопка TP (программа движения транспорта)Кнопка RDS (сист...
Page 58 - ОСНОВНЫЕ ОПЕРАЦИИ; Включение; Выберите источник сигнала.; Чтобы выключить устройство
5 Р УССКИЙ ОСНОВНЫЕ ОПЕРАЦИИ Включение 1 Включите устройство. Примечания в отношении управленияв одно касание: Когда Вы выбираете источник сигнала впункте 2 ниже, устройство автоматическивключается. Вам не нужно нажимать этукнопку для того, чтобы включитьустройство. 2 Выберите источник сигнала. О то...
Page 59 - ОСНОВНЫЕ ОПЕРАЦИИ С РАДИОПРИЕМНИКОМ; Прослушивание радио; Начинайте поиск радиостанции.
6 Р УССКИЙ ОСНОВНЫЕ ОПЕРАЦИИ С РАДИОПРИЕМНИКОМ MO TP RDS PTY DISP 8 9 10 11 12 7 DAB Прослушивание радио Вы можете использовать автоматический илиручной поиск при настройке на конкретнуюрадиостанцию. Автоматический поискрадиостанции: Автоматическийпоиск 1 Выберите диапазон (FM1 – 3, AM). Примечание:...
Page 60 - Нажмите и держите кнопку
7 Р УССКИЙ MO MO RND Поиск радиостанции вручную:Ручной поиск 1 Выберите диапазон (FM1 – 3, AM). Примечание: Этот приемник работает на трехдиапазонах FM (FM1, FM2, FM3). Вы можетепользоваться любым из них для того, чтобыслушать радиовещание на частотах FM. 2 Нажмите и держите кнопку ¢ или 4 до тех по...
Page 61 - Ручное программирование
8 Р УССКИЙ Местные радиостанции FM с самым сильнымсигналом находятся и запоминаютсяавтоматически в том диапазоне, который Вывыберите (FM1, FM2 или FM3). Эти станциипрограммируются на нумерованных кнопках— от № 1 (самая низкая частота) до № 6(самая высокая частота). По завершенииавтоматического прогр...
Page 63 - ОПЕРАЦИИ С RDS; Режим
10 Р УССКИЙ ОПЕРАЦИИ С RDS Без правильного получения этих данных оттой радиостанции RDS, которую Выслушаете, функция Сеть–отслеживающийприем работать не будет. Для того, чтобы использовать Сеть–отслеживающий прием, нажмите и держите в течение более 1 секунды кнопку TP RDS(программа движения транспор...
Page 64 - Резервный прием PTY; Резервный прием ТА
11 Р УССКИЙ Если программа движения транспортаначинает передаваться при включенномрезервном режиме ТА, появляется надпись“TRAFFIC” (движение транспорта), ивоспроизводимый источник сигналапереключается на диапазон FM. Громкостьповышается до запрограммированногоуровня громкости TA (смотрите страницу 1...
Page 67 - Установка уровня громкости ТА
14 Р УССКИЙ Изменение режима работыдисплея во времяпрослушивания радиостанцииFM Вы можете изменить первоначальнуюиндикацию на экране дисплея на названиерадиостанции (PS NAME), частотурадиостанции (FREQ) или время часов(CLOCK), когда слушаете какую-либорадиостанцию FM RDS.• Смотрите также “Изменение ...
Page 69 - Прослушивание кассеты; ОПЕРАЦИИ С МАГНИТОФОНОМ
16 Р УССКИЙ Прослушивание кассеты Вы можете проигрывать магнитные лентытипа 1 (нормальные). 1 Вставьте кассету вкассетоприемник. Устройство включается, икассета начинаетвоспроизводитьсяавтоматически.Когда одна сторонакассеты достигает своегоконца во времявоспроизведения,автоматически начинаетвоспрои...
Page 71 - Нажмите кнопку
18 Р УССКИЙ Другие полезныефункции магнитофона Пропуск пустых участков накассете Вы можете пропускать пустые участки междумелодиями (Пропуск пустых участков).Когда эта функция включена, устройствопропускает пустые участки в 15 секунд иболее, ускоренно перематывает пленкувперед до следующей мелодии и...
Page 72 - НАСТРОЙКА ЗВУКА; Настройка звука; VOL
19 Р УССКИЙ 1 Выберите тот параметр, которыйВы хотите настроить. При каждом нажатии кнопкирегулируемые параметрыменяются следующимобразом: 2 Настройте уровень. Примечание: При обычной эксплуатации диск управлениявыполняет функции регулятора громкости.Поэтому Вам не требуется выбирать “VOL”(громкость...
Page 73 - BEAT
20 Р УССКИЙ Использование памятиуправления звуком Вы можете выбрать и запомнитьзапрограммированную настройку звука,подходящую для каждого источникавоспроизведения (Сложная SCM (память управления звуком)) . Выбор и запоминаниережимов звучания После того, как Вы выбрали режим звучания,он сохраняется в...
Page 76 - Установка часов; Установите систему часов.; ДРУГИЕ ГЛАВНЫЕ ФУНКЦИИ; Основная процедура; Часы
23 Р УССКИЙ Установка часов Вы можете также установить систему часовлибо на 24 часа, либо на 12 часов. 1 Нажмите и держите кнопку SEL(выбор) в течение более 2 секундс тем, чтобы на экране дисплеяпоявился один из параметровPSM. (Смотрите страницу 24). 2 Установите час. 1 Выберите “CLOCK H (час на час...
Page 77 - Параметры предпочтительного режима установки (PSM)
24 Р УССКИЙ CLOCK H Настройка часа CLOCK M Настройка минуты SCM LINK Связь памятиуправления звуком 24H/12H * 24/12-часовое времяна экране дисплея AUTO ADJ * Автоматическая установка часов DISPMODE * Режим работы дисплея CH DISP * Проигрыватель-автоматна экране дисплея PTY STBY * Резервный PTY PTY SR...
Page 78 - Для отмены
25 Р УССКИЙ Для выбора приглушения звукапри телефонном звонке– TEL (телефон) Этот режим используется, когдаподсоединена система сотового телефона. Взависимости от используемой телефоннойсистемы выберите “MUTING 1” или“MUTING 2”, в зависимости от того, какой изних подавляет звук этого устройства.При ...
Page 79 - Освободите панель управления.
26 Р УССКИЙ Отсоединение панелиуправления Вы можете отсоединить панель управления,когда выходите из машины.При отсоединении или установке панелиуправления соблюдайте осторожность, чтобыне повредить разъемы на задней сторонепанели управления и на держателе панели. Как отсоединить панельуправления Пер...
Page 80 - ОПЕРАЦИИ С ПРОИГРЫВАТЕЛЕМ-
27 Р УССКИЙ Воспроизведениекомпакт-дисков Выберите проигрыватель-автоматкомпакт-дисков (CD-CH). Воспроизведение начинается спервой дорожки первого диска.Воспроизводятся все дорожкина всех дисках. • На экране дисплея показана следующая информация, в зависимости от настройки “CHDISP (проигрыватель-авт...
Page 81 - Отменено
28 Р УССКИЙ Выбор режимоввоспроизведениякомпакт-дисков Чтобы воспроизводить дорожкипроизвольно (Произвольноевоспроизведение) При каждом нажатии этой кнопкирежим произвольноговоспроизведения компакт-дисковменяется следующим образом: RND1 Светится Все дорожки (произвольно1) текущегодиска, затемдорожки...
Page 82 - ОПЕРАЦИИ С ВНЕШНИМИ КОМПОНЕНТАМИ
29 Р УССКИЙ ОПЕРАЦИИ С ВНЕШНИМИ КОМПОНЕНТАМИ Данный раздел относится только кKS-FX725R. Воспроизведение навнешнем компоненте Вы можете подключить внешний компонент кконтактному гнезду проигрывателя-автоматакомпакт-дисков на задней панели с помощьюАдаптера входной линии KS-U57 (не включенв комплект п...
Page 83 - ОПЕРАЦИИ С ТЮНЕРОМ DAB
30 Р УССКИЙ Настройка на группу иодну из служб Типичная группа состоит из 6 или болеепрограмм (служб), передаваемыходновременно. После настройки на группу Выможете выбрать ту службу, которую Выхотите слушать. Перед тем, как Вы начнете.... Нажмите и тут же отпустите кнопку DAB(FM AM), если магнитофон...
Page 84 - Начинайте поиск группы.; Чтобы восстановить тюнер FM/AM
31 Р УССКИЙ 3 Начинайте поиск группы. После того, как группа найдена, поискпрекращается. Чтобы остановить поиск до того, какбудет найдена группа, нажмите на ту же самую кнопку, которую Вынажимали, чтобы начать поиск. 4 Выберите службу, которую Выхотите слушать. время часов Название группы Название с...
Page 87 - ВЫЯВЛЕНИЕ НЕИСПРАВНОСТЕЙ; Способ устранения
34 Р УССКИЙ ВЫЯВЛЕНИЕ НЕИСПРАВНОСТЕЙ То, что может вначале показаться неисправностью, не всегда представляет собой серьезнуюпроблему. Перед тем, как обращаться в центр технического обслуживания, проверьтеследующее. Способ устранения Вставляйте кассету так,чтобы незащищеннаясторона пленки былаобращен...
Page 88 - Симптомы
35 Р УССКИЙ только в отношении KS-FX725R: Симптомы • На экране дисплея появляется надпись“NO DISC” (нет диска). • На экране дисплея появляется надпись“NO MAG”. • На экране дисплея появляется надпись“RESET 8” (“возврат висходное положение 8”). • На экране дисплея появляется надпись“RESET 1” – “RESET ...
Page 89 - ТЕХНИЧЕСКОЕ ОБСЛУЖИВАНИЕ
36 Р УССКИЙ Это устройство требует минимумобслуживания, но Вы можете продлить срокего службы, если будете следоватьприведенным ниже инструкциям. Чистка головки • Чистите головку через каждые 10 часов использования с помощью чистящейкассеты влажного типа (продаются вмагазинах звуковоспроизводящейаппа...
Page 90 - СЕКЦИЯ КАССЕТНОЙ ДЕКИ; ТЕХНИЧЕСКИЕ ХАРАКТЕРИСТИКИ; СЕКЦИЯ ТЮНЕРА
37 Р УССКИЙ [Тюнер FM] Используемая чувствительность: 11,3 дБф (1,0 мВ/75 Ω ) 50 дБ пороговая чувствительность: 16,3 дБф (1,8 мВ/75 Ω ) Избирательность обходного канала (400 кГц): 65 дБ Частотная характеристика: От 40 Гц до 15 000 Гц Стерео разделение: 30 дБКоэффициент захвата: 1,5 дБ [Тюнер MW] Чув...
Page 91 - Having TROUBLE with operation?; Refer to page of How to reset your unit; Затруднения при эксплуатации?; Для получения информации о перезагрузке Вашего устройства
EN, RU 1101KKSMDTJEIN VICTOR COMPANY OF JAPAN, LIMITED J V C Having TROUBLE with operation? Please reset your unit Refer to page of How to reset your unit Затруднения при эксплуатации? Пожалуйста, перезагрузите Ваше устройство Для получения информации о перезагрузке Вашего устройства обратитесь на с...
Page 94 - РУССКИЙ; ПРЕДОСТЕРЕЖЕНИЯ по питанию и подключению громкоговорителей:; иначе устройство будет повреждено.; PRECAUTIONS on power supply and speaker connections:; unit will be seriously damaged.; Typical Connections / Типичные подключения
3 РУССКИЙ ПРЕДОСТЕРЕЖЕНИЯ по питанию и подключению громкоговорителей: • НЕ подключайте провода громкоговорителей к аккумулятору автомобиля, иначе устройство будет повреждено. • Правильно подключите черный провод (земля), желтый провод (в аккумулятор, постоянный 12 В) и красный провод (в вспомогатель...
Page 95 - Amplifier / Усилитель; Connecting the leads / Подключение контактов; BЫЯВЛЕНИЕ НЕИСПРАВНОСТЕЙ; External component / Внешний компонент
4 INPUT R L R L LINE OUT REAR L R L R L R FRONT R L R L INPUT KS-FX725RKS-F525 B Connections Adding Other Equipment / Подключение других устройств Amplifier / Усилитель Remote leadПровод внешнего устройства Signal cord (not supplied with this unit)Кабель сигнала (не входит в комплект) Rear speakers ...
Page 97 - CONTENTS; How to reset your unit
2 ENGLISH Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. Control panel—KS-FX725R ..................... 3 LOCATION OF THE BUTTONS ............ 3 Control p...
Page 98 - LOCATION OF THE BUTTONS; Control panel—KS-FX725R; Display window
3 ENGLISH LOCATION OF THE BUTTONS Control panel—KS-FX725R 1 (standby/on/attenuator) button 2 Control dial 3 DISP (display) button 4 TP (traffic programme)RDS (radio data system) button 5 PTY (programme type) button 6 Cassette compartment 7 FM AM button • Also functions as the DAB button. 8 TAPE 23 b...
Page 99 - Control panel—KS-F525
4 ENGLISH LOCATION OF THE BUTTONS Control panel—KS-F525 1 (standby/on/attenuator) button 2 Control dial 3 LOUD (loudness) button 4 DISP (display) button 5 SCAN button 6 Cassette compar tment 7 TAPE button 8 FM button 9 0 (eject) button p ¢ / 4 buttons • Also functions as SSM buttons when pressed tog...
Page 100 - BASIC OPERATIONS; Turning on the power
5 ENGLISH 3 Adjust the volume. 4 Adjust the sound as you want.(See pages 19 – 22.) To drop the volume in a moment Press briefly while listening to any source. “ATT” starts flashing on the display, andthe volume level will drop in a moment.To resume the previous volume level, press thebutton briefly ...
Page 101 - RADIO BASIC OPERATIONS; Listening to the radio
6 ENGLISH RADIO BASIC OPERATIONS MO TP RDS PTY DISP 8 9 10 11 12 7 DAB Listening to the radio You can use either automatic searching or manualsearching to tune in to a particular station. Searching a station automatically:Auto search 1 Select the band (FM1 – 3, AM). Note: This receiver has three FM ...
Page 102 - Press and hold
7 ENGLISH Searching a station manually:Manual search 1 Select the band (FM1 – 3, AM). Note: This receiver has three FM bands (FM1, FM2,FM3). You can use any one of them to listen to anFM broadcast. 2 Press and hold ¢ or 4 until “M (manual)” starts flashing on thedisplay. Lights up when receivingan F...
Page 103 - Manual preset; Storing stations in memory; FM station automatic preset: SSM
8 ENGLISH Local FM stations with the strongest signals aresearched and stored automatically in the bandnumber you have selected (FM1, FM2 or FM3).These stations are preset in the number buttons —No.1 (lowest frequency) to No.6 (highest frequency).When automatic preset is over, the station storedin n...
Page 104 - Tuning in to a preset station
9 ENGLISH Tuning in to a preset station You can easily tune in to a preset station.Remember that you must store stations first. If youhave not stored them yet, see “Storing stations inmemory” on pages 8 and 9. 1 Select the band (FM1 – 3, AM). 2 Select the number (1 – 6) for the presetstation you wan...
Page 105 - RDS OPERATIONS; What you can do with RDS
10 ENGLISH RDS OPERATIONS To use Network-Tracking Reception, press andhold TP RDS (Traffic Programme/Radio DataSystem) for more than 1 second. Each time youpress and hold the button, Networ k-TrackingReception modes change as follows: Mode 1The AF indicator lights up but the REG indicatordoes not.Ne...
Page 106 - Using Standby Reception; TA Standby Reception
11 ENGLISH PTY Standby Reception When you press PTY while listeningto an FM station, the PTY indicator islit during reception of a PTY stationand the PTY standby mode isengaged. The selected PTY namestored on page 12 flashes for 5seconds. • When the station being received is not a PTY station, the P...
Page 107 - Searching your favorite programme; To store your favorite programme types
12 ENGLISH Selecting your favorite programme forPTY Standby Reception You can select your favorite programme for PTYStandby Reception to store in memory.When shipped from the factory, “NEWS” is storedas the programme type for PTY Standby Reception. 1 Press and hold SEL (select) for morethan 2 second...
Page 109 - Setting the TA volume level; Station name
14 ENGLISH Changing the display mode whilelistening to an FM station You can change the initial indication on the displayto station name (PS NAME), station frequency(FREQ) or clock time (CLOCK), while listening toan FM RDS station.• See also “Changing the general settings (PSM)” on pages 23 and 24. ...
Page 111 - Listening to a cassette; Select the tape direction.; TAPE OPERATIONS; To stop play and eject the cassette
16 ENGLISH Listening to a cassette You can play back type 1 (normal) tapes. 1 Insert a cassette into the cassettecompartment. The unit turns on and tapeplay starts automatically.When one side of the tapereaches its end during play,the other side of the tapeautomatically starts playing(Auto Reverse)....
Page 112 - Prohibiting cassette ejection; Finding the beginning of a tune
17 ENGLISH Prohibiting cassette ejection You can prohibit cassette ejection and can “lock”a cassette in the cassette compar tment.Press and hold TAPE 23 and 0 for more than 2 seconds. “NO EJECT” flashes on the display forabout 5 seconds, and the cassette is “locked.” To cancel the prohibition and “u...
Page 113 - Other convenient tape functions; Skipping the blank portions on the tape; Playing the current tune repeatedly
18 ENGLISH Other convenient tape functions Skipping the blank portions on the tape You can skip blank portions between the tunes(Blank Skip).When this function is on, the unit skips blankportions of 15 seconds or more, fast-forwards tothe next tune, then starts playing it.• See also “Changing the ge...
Page 114 - Select the item you want to adjust.; SOUND ADJUSTMENTS; Adjusting the sound
19 ENGLISH 1 Select the item you want to adjust. Each time you press the button,the adjustable items change asfollows: SOUND ADJUSTMENTS Adjusting the sound You can adjust the sound characteristics to yourpreference. Indication To do: Range BAS Adjust the bass. –06 (min.) |+06 (max.) TRE Adjust the ...
Page 115 - Using the sound control memory; Selecting and storing the sound modes; Select the sound mode you want.
20 ENGLISH Turning on/off the loudnessfunction (only for KS-F525) The human ear is less sensitive to low and highfrequencies at low volumes.The loudness function can boost thesefrequencies to produce a well-balanced sound atlow volume levels.Each time you press LOUD, the loudnessfunction turns on an...
Page 116 - Recalling the sound modes
21 ENGLISH • When “SCM LINK” is set to “LINK ON,” the selected sound mode can be stored in memoryfor the current source and the effect applies onlyto the current source. • When “SCM LINK” is set to “LINK OFF,” the selected sound mode effect applies to any source. Recalling the sound modes When “SCM ...
Page 117 - To reset to the factory settings
22 ENGLISH Storing your own soundadjustments You can adjust the sound modes (BEAT, SOFT,POP) to your preference and store your ownadjustments in memory.• There is a time limit in doing the following procedure. If the setting is canceled before youfinish, start from step 1 again. 1 Call up the sound ...
Page 118 - Setting the clock; Set the clock system.; OTHER MAIN FUNCTIONS; Basic Procedure; Clock
23 ENGLISH Setting the clock You can also set the clock system to either 24 hoursor 12 hours. 1 Press and hold SEL (select) for morethan 2 seconds so that one of the PSMitems appears on the display.(See page 24.) 2 Set the hour. 1 Select “CLOCK H (hour)” if not shown onthe display. 2 Adjust the hour...
Page 119 - Adjust the PSM item selected.
24 ENGLISH LINK ON 24H 24H 12H ON 23 LINK ON Advance Advance ON Seepage Factory-presetsettings 2 1 3 Clockwise Set. OFF Back Back LINK OFF 14 Counter-clockwise Select. Hold. CLOCK PS NAME FREQ PS NAME DISC 25 3 Adjust the PSM item selected. 4 Repeat steps 2 and 3 to adjust theother PSM items if nece...
Page 120 - TEL; To cancel Advanced SCM –; SCM LINK; To select the changer display –; CH DISP; To select the level meter –; LEVEL
25 ENGLISH To select the telephone muting – TEL This mode is used when a cellular phone system isconnected. Depending on the phone system used,select either “MUTING 1” or “MUTING 2,” whichevermutes the sounds from this unit.When shipped from the factor y, this mode isdeactivated. • MUTING 1: Select ...
Page 121 - Detaching the control panel; Unlock the control panel.; Attaching the control panel
26 ENGLISH Detaching the control panel You can detach the contol panel when leaving thecar.When detaching or attaching the control panel,be careful not to damage the connectors on theback of the control panel and on the panel holder. Detaching the control panel Before detaching the control panel, be...
Page 122 - Playing CDs; To fast-forward or reverse the track; CD CHANGER OPERATIONS
27 ENGLISH Playing CDs Select the CD automatic changer (CD-CH). Playback starts from the first trackof the first disc.All tracks of all discs are played back. • The display shows the following infor mation, depending on the “CH DISP (CD changer display)”setting (see page 25.) • When “DISC” is select...
Page 123 - Selecting CD playback modes; To play back tracks at random (Random Play); Canceled
28 ENGLISH Selecting CD playback modes To play back tracks at random (Random Play) Each time you press the button, CDrandom play mode changes asfollows: RND1 Lights All tracks of the current (random1) disc, then the tracks ofthe next disc, and so on. RND2 Flashes All tracks of all discs (random2) in...
Page 124 - EXTERNAL COMPONENT OPERATIONS; Playing an external component
ENGLISH 29 EXTERNAL COMPONENT OPERATIONS 2 Turn on the connected componentand start playing the source. 3 Adjust the volume. 4 Adjust the sound characteristicsyou want. (See page 19.) This section is only for KS-FX725R. Playing an external component You can connect the external component to theCD ch...
Page 125 - Select the DAB tuner.; DAB TUNER OPERATIONS
ENGLISH 30 This section is only for KS-FX725R. We recommend that you use DAB (Digital AudioBroadcasting) tuner KT-DB1500 with your unit.If you have another DAB tuner, consult your JVCIN-CAR ENTERTAINMENT dealer.• Refer also to the Instructions supplied with your DAB tuner. What is DAB system? DAB is...
Page 126 - Clock time; To restore the FM/AM tuner; Start searching an ensemble.
ENGLISH 31 Clock time Service name Ensemble name Band/Preset number Frequency Channel number To change the display information whiletuning in to an ensemble Normally service name is shown on the display.If you want to change the display information, pressDISP (display).Each time you press the button...
Page 129 - TROUBLESHOOTING; Remedies
34 ENGLISH TROUBLESHOOTING What appears to be trouble is not always serious. Check the following points before calling a servicecenter. Remedies Insert the cassette with theexposed tape facing right. Press and hold TAPE 23 and 0 for more than two seconds. Clean it with a head cleaningtape. Check the...
Page 131 - MAINTENANCE
36 ENGLISH This unit requires very little attention, but you willbe able to extend the life of the unit if you followthe instructions below. To clean the head • Clean the head after every 10 hours of use using a wet-type head cleaning tape (available at anaudio store).When the head becomes dir ty, y...
Page 132 - SPECIFICATIONS; AUDIO AMPLIFIER SECTION
37 ENGLISH SPECIFICATIONS AUDIO AMPLIFIER SECTION Maximum Power Output: KS-FX725R: Front: 45 W per channel Rear: 45 W per channel KS-F525: Front: 40 W per channel Rear: 40 W per channel Continuous Power Output (RMS): KS-FX725R: Front: 17 W per channel into 4 Ω , 40 Hz to 20 000 Hz at no more than0.8...